Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > TERMINALS OF ECM

for Preparation Click here



A107881E94

Measure the voltage according to the value(s) in the table below.

HINT:
The standard voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard voltage for that pair of terminals, which is displayed in the "Specified Condition" column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
A24-1 (BATT) - D74-81 (E1)
L - BR
Battery (for measuring the battery voltage and for the ECM memory)
Always
11 to 14 V
D74-41 (+BM) - D74-81 (E1)
P - BR
Power source of throttle motor
Always
11 to 14 V
A24-28 (IGSW) - D74-81 (E1)
LG - BR
Ignition switch
Ignition switch ON
11 to 14 V
A24-3 (+B) - D74-81 (E1)
GR - BR
Power source of ECM
Ignition switch ON
11 to 14 V
A24-2 (+B2) - D74-81 (E1)
GR - BR
Power source of ECM
Ignition switch ON
11 to 14 V
D74-58 (OC1+) - D74-57 (OC1-)
L-B - R-B
Camshaft timing oil control valve (for intake side of bank 1)
Ignition switch ON
Pulse generation
(See waveform 1)
D74-52 (OC2+) - D74-51 (OC2-)
B - B-L
Camshaft timing oil control valve (for intake side bank 2)
Ignition switch ON
Pulse generation
(See waveform 1)
D74-56 (OE1+) - D74-55 (OE1-)
L-R - L
Camshaft timing oil control valve (for exhaust side of bank 1)
Ignition switch ON
Pulse generation
(See waveform 1)
D74-50 (OE2+) - D74-49 (OE2-)
L-W - L-B
Camshaft timing oil control valve (for exhaust side of bank 2)
Ignition switch ON
Pulse generation
(See waveform 1)
A24-34 (MREL) - D74-81 (E1)
W - BR
EFI relay
Ignition switch ON
11 to 14 V
D74-67 (VCV1) - D74-97 (ETHW)
L - BR
Power source of sensor (specific voltage)
Ignition switch ON
4.5 to 5.5 V
D74-66 (VCV2) - D74-98 (E2)
L - BR
Power source of sensor (specific voltage)
Ignition switch ON
4.5 to 5.5 V
D74-74 (VG) - D74-75 (E2G)
L-Y - G-W
Mass air flow meter
Idling, shift lever position P or N, A/C switch off
0.5 to 3.0 V
D74-73 (THA) - D74-98 (E2)
Y-B - BR
Intake air temperature sensor
Idling, intake air temperature 20°C (68°F)
0.5 to 3.4 V
D74-76 (THW) - D74-97 (ETHW)
G-B - BR
Engine coolant temperature sensor
Idling, engine coolant temperature 80°C (176°F)
0.2 to 1.0 V
D74-80 (VCTA) - D74-79 (ETA)
L - B
Power source of throttle position sensor (specific voltage)
Ignition switch ON
4.5 to 5.5 V
D74-78 (VTA1) - D74-79 (ETA)
R-Y - B
Throttle position sensor (for engine control)
Ignition switch ON, throttle valve fully closed
0.5 to 1.2 V
Ignition switch ON, throttle valve fully open
3.2 to 4.8 V
D74-77 (VTA2) - D74-79 (ETA)
Y-B - B
Throttle position sensor (for sensor malfunction detection)
Ignition switch ON, throttle valve fully closed
2.1 to 3.1 V
Ignition switch ON, throttle valve fully open
4.5 to 5.0 V
A24-55 (VPA) - A24-58 (EPA)
W - BE
Accelerator pedal position sensor (for engine control)
Ignition switch ON, accelerator pedal fully released
0.5 to 1.1 V
Ignition switch ON, accelerator pedal fully depressed
2.6 to 4.5 V
A24-56 (VPA2) - A24-60 (EPA2)
LG - P
Accelerator pedal position sensor (for sensor malfunction detection)
Ignition switch ON, accelerator pedal fully released
1.2 to 2.0 V
Ignition switch ON, accelerator pedal fully depressed
3.4 to 4.7 V
A24-57 (VCPA) - A24-58 (EPA)
B - BE
Power source of accelerator pedal position sensor (for VPA)
Ignition switch ON
4.5 to 5.5 V
A24-59 (VCP2) - A24-60 (EPA2)
V - P
Power source of accelerator pedal position sensor (for VPA2)
Ignition switch ON
4.5 to 5.5 V
D74-22 (HA1A) - D74-23 (E04)
D74-20 (HA2A) - D74-21 (E05)
L - W-B
G - W-B
Air fuel ratio sensor heater
Idling
Pulse generation
(See waveform 2)
Ignition switch ON
11 to 14 V
D74-126 (A1A+) - D74-81 (E1)
G - BR
Air fuel ratio sensor
Ignition switch ON
3.3 V*
D74-103 (A2A+) - D74-81 (E1)
V - BR
Air fuel ratio sensor
Ignition switch ON
3.3 V*
D74-125 (A1A-) - D74-81 (E1)
R - BR
Air fuel ratio sensor
Ignition switch ON
2.9 V*
D74-102 (A2A-) - D74-81 (E1)
P - BR
Air fuel ratio sensor
Ignition switch ON
2.9 V*
D74-45 (HT1B) - D74-46 (E03)
D74-44 (HT2B) - D74-46 (E03)
G - W-B
B - W-B
Heated oxygen sensor heater
Idling
Below 3.0 V
Ignition switch ON
11 to 14 V
D74-114 (OX1B) - D74-115 (EX1B)
D74-112 (OX2B) - D74-113 (EX2B)
W - BR
B - BR
Heated oxygen sensor
Engine speed maintained at 2500 rpm for 2 minutes after warming up engine
Pulse generation
(See waveform 3)
D74-86 (#10) - D74-43 (E01)
D74-109 (#20) - D74-43 (E01)
D74-85 (#30) - D74-43 (E01)
D74-108 (#40) - D74-43 (E01)
D74-84 (#50) - D74-43 (E01)
D74-107 (#60) - D74-43 (E01)
R-L - W-B
L - W-B
R - W-B
Y - W-B
G - W-B
R - W-B
Fuel injector assembly
Ignition switch ON
11 to 14 V
Idling
Pulse generation
(See waveform 4)
D74-94 (KNK1) - D74-93 (EKNK)
G - R
Knock sensor (bank 1)
Engine speed maintained at 4000 rpm after warming up engine
Pulse generation
(See waveform 5)
D74-117 (KNK2) - D74-116 (EKN2)
W - B
Knock sensor (bank 2)
Engine speed maintained at 4000 rpm after warming up engine
Pulse generation
(See waveform 5)
D74-90 (VV1+) - D74-89 (VV1-)
R - L-R
VVT sensor (intake side of bank 1)
Idling
Pulse generation
(See waveform 6)
D74-87 (VV2+) - D74-88 (VV2-)
R - G
VVT sensor (intake side of bank 2)
Idling
Pulse generation
(See waveform 6)
D74-69 (EV1+) - D74-68 (EV1-)
R-L - B
VVT sensor (exhaust side of bank 1)
Idling
Pulse generation
(See waveform 16)
D74-64 (EV2+) - D74-65 (EV2-)
R-L - B
VVT sensor (exhaust side of bank 2)
Idling
Pulse generation
(See waveform 16)
D74-110 (NE+) - D74-111 (NE-)
B - W
Crankshaft position sensor
Idling
Pulse generation
(See waveform 6)
D74-40 (IGT1) - D74-81 (E1)
D74-39 (IGT2) - D74-81 (E1)
D74-38 (IGT3) - D74-81 (E1)
D74-37 (IGT4) - D74-81 (E1)
D74-36 (IGT5) - D74-81 (E1)
D74-35 (IGT6) - D74-81 (E1)
B-R - BR
L-Y - BR
B - BR
L-B - BR
G-R - BR
G - BR
Ignition coil
(ignition signal)
Idling
Pulse generation
(See waveform 7)
D74-104 (IGF1) - D74-81 (E1)
G-B - BR
Ignition coil
(ignition confirmation signal)
Ignition switch ON
4.5 to 5.5 V
Idling
Pulse generation
(See waveform 7)
D74-63 (PRG) - D74-81 (E1)
L-B - BR
Purge VSV
Ignition switch ON
11 to 14 V
Idling
Pulse generation
(See waveform 8)
A24-13 (SPD) - D74-81 (E1)
B - BR
Speed signal from combination meter
Ignition switch ON, driving wheels rotated slowly
Pulse generation
(See waveform 9)
A24-46 (STA) - D74-81 (E1)
R - BR
Starter signal
Cranking
6.0 V or higher
A24-36 (STP) - D74-81 (E1)
SB - BR
Stop light switch
Brake pedal depressed
7.5 to 14 V
Brake pedal released
Below 1.5 V
A24-35 (ST1-) - D74-81 (E1)
R - BR
Stop light switch (opposite to STP terminal)
Ignition switch ON, brake pedal depressed
Below 1.5 V
Ignition switch ON, brake pedal released
7.5 to 14 V
D74-120 (NSW) - D74-81 (E1)
L - BR
Park/neutral position switch
Ignition switch ON, shift lever in P or N
Below 3.0 V
Ignition switch ON, shift lever not in P or N
11 to 14 V
D74-19 (M+) - D74-82 (ME01)
R - W-B
Throttle actuator
Idling with warm engine
Pulse generation
(See waveform 10)
D74-18 (M-) - D74-82 (ME01)
G - W-B
Throttle actuator
Idling with warm engine
Pulse generation
(See waveform 11)
A24-24 (W) - D74-81 (E1)
P - BR
MIL
Ignition switch ON
Below 3.0 V
Idling
11 to 14 V
A24-16 (TC) - D74-81 (E1)
V - BR
Terminal TC of DLC3
Ignition switch ON
11 to 14 V
A24-15 (TACH) - D74-81 (E1)
GR - BR
Engine speed
Idling
Pulse generation
(See waveform 12)
D74-72 (PSP) - D74-98 (E2)
G - BR
Power steering oil pressure sensor
Ignition switch ON
0.33 to 3.60 V
A24-30 (VPMP) - D74-81 (E1)
V - BR
Vent valve
(built into canister pump module)
Ignition switch ON
11 to 14 V
A24-49 (MPMP) - D74-81 (E1)
W - BR
Leak detection pump
(built into canister pump module)
Leak detection pump off
0 to 3 V
Leak detection pump on
11 to 14 V
D74-121 (PPMP) - D74-97 (ETHW)
P - BR
Canister pressure sensor
(built into canister pump module)
Ignition switch ON
3 to 3.6 V
D74-28 (AIRV) - D74-81 (E1)
BR - BR
Emission control valve for secondary air injection system
Idling
11 to 14 V
D74-54 (AIRP) - D74-81 (E1)
P - BR
Air pump control
Idling
11 to 14 V
D74-30 (AIDI) - D74-81 (E1)
G - BR
Diagnostic information signal for secondary air injection system
Air injection system operating
Pulse generation
(See waveform 15)
D74-60 (AIR1) - D74-81 (E1)
B - BR
No. 2 emission control valve for secondary air injection system
Idling
11 to 14 V
A24-54 (AIP) - D74-98 (E2)
Y - BR
Secondary air injection system pressure signal
Ignition switch ON
0.5 to 4.5 V
A24-53 (AIP2) - D74-98 (E2)
G - BR
Secondary air injection system pressure signal
Ignition switch ON
0.5 to 4.5 V
A24-10 (CANH) - D74-81 (E1)
GR - BR
CAN communication line
Ignition switch ON
Pulse generation
(See waveform 13)
A24-11 (CANL) - D74-81 (E1)
W - BR
CAN communication line
Ignition switch ON
Pulse generation
(See waveform 14)
A24-52 (FPC) - D74-81 (E1)
BE - BR
Fuel pump control
Engine stopped and ignition switch ON
Below 1.5 V
A24-14 (STSW) - D74-81 (E1)
BR - BR
Ignition switch signal
Shift lever in P or N, ignition switch START
6.0 V or higher
A24-41 (ACCR) - D74-81 (E1)
BR - BR
ACC (accessory) relay control signal
Cranking
Below 1.5 V
D74-16 (STAR) - D74-81 (E1)
L - BR
Starter relay control
Ignition switch ON
Below 1.5 V
Cranking
6.0 V or higher
D74-32 (ALT) - D74-81 (E1)
R - BR
Generator
Ignition switch ON
11 to 14 V
*: The ECM terminal voltage is constant regardless of the output voltage from the sensor.

WAVEFORM 1
A093229E07
Camshaft Timing Oil Control Valve 
ECM Terminal Name
Between OC1+ and OC1-
Between OC2+ and OC2-
Between OE1+ and OE1-
Between OE2+ and OE2-
Tester Range
5 V/DIV., 1 msec./DIV.
Condition
Idling

WAVEFORM 2
A172534E04
Air Fuel Ratio Sensor Heater 
ECM Terminal Name
CH1: Between HA1A and E04
CH2: Between HA2A and E05
Tester Range
5 V/DIV., 10 msec./DIV.
Condition
Idling

HINT:
The wavelength varies in accordance with the engine operating condition.


WAVEFORM 3
A088863E02
Heated Oxygen Sensor 
ECM Terminal Name
Between OX1B and EX1B or OX2B and EX2B
Tester Range
0.2 V/DIV., 200 msec./DIV.
Condition
Engine speed maintained at 2500 rpm for 2 minutes after warming up engine

HINT:
In the Data List, items O2S B1S2 and O2S B2S2 show the ECM input values from the heated oxygen sensors.


WAVEFORM 4
G035622E03
Fuel Injector Assembly 
ECM Terminal Name
Between #10 (to 60) and E01
Tester Range
30 V/DIV., 20 msec./DIV.
Condition
Idling

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 5
A085286E53
Knock Sensor 
ECM Terminal Name
Between KNK1 and EKNK or KNK2 and EKN2
Tester Range
1 V/DIV., 0.01 to 1 msec./DIV.
Condition
Engine speed maintained at 4000 rpm after warming up engine

HINT:
  1. The wavelength becomes shorter as the engine speed increases.
  2. The waveforms and amplitudes displayed on the Techstream differ slightly depending on the vehicle.


WAVEFORM 6
A199235E02
Crankshaft Position Sensor and VVT Sensor for Intake Side 
ECM Terminal Name
(a) Between NE+ and NE-
(b) Between VV1+ and VV1- or VV2+ and VV2-
Tester Range
5 V/DIV., 20 msec./DIV.
Condition
Idling

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 7
G035664E03
  1. Igniter IGT signal (from ECM to ignition coil)

  2. Igniter IGF signal (from ignition coil to ECM)
    ECM Terminal Name
    (a) Between IGT1 (to 6) and E1
    (b) Between IGF1 and E1
    Tester Ranges
    2 V/DIV., 20 msec./DIV.
    Condition
    Idling

    HINT:
    The wavelength becomes shorter as the engine speed increases.


WAVEFORM 8
A205411E02
Purge VSV 
ECM Terminal Name
Between PRG and E1
Tester Range
10 V/DIV., 20 msec./DIV.
Condition
Idling

HINT:
If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.


WAVEFORM 9
A093224E02
Vehicle Speed Signal 
ECM Terminal Name
Between SPD and E1
Tester Range
2 V/DIV., 20 msec./DIV.
Condition
Ignition switch ON, driving wheels rotated slowly

HINT:
The wavelength becomes shorter as the vehicle speed increases.


WAVEFORM 10
A208000E06
Positive Terminal of Throttle Actuator 
ECM Terminal Name
Between M+ and ME01
Tester Range
5 V/DIV., 1 msec./DIV.
Condition
Idling with warm engine

HINT:
The duty ratio varies depending on the throttle actuator operation.


WAVEFORM 11
A245848E04
Negative Terminal of Throttle Actuator 
ECM Terminal Name
Between M- and ME01
Tester Range
5 V/DIV., 1 msec./DIV.
Condition
Idling with warm engine

HINT:
The duty ratio varies depending on the throttle actuator operation.


WAVEFORM 12
A093225E03
Engine Speed Signal 
ECM Terminal Name
Between TACH and E1
Tester Range
5 V/DIV., 10 msec./DIV.
Condition
Idling

HINT:
The wavelength becomes shorter as the engine speed increases.


WAVEFORM 13
A086154E14
CAN Communication Signal (Reference) 
ECM Terminal Name
Between CANH and E1
Tester Range
1 V/DIV., 10 μsec./DIV.
Condition
Ignition switch ON

HINT:
The waveform varies depending on the CAN communication signal.


WAVEFORM 14
A086155E15
CAN Communication Signal (Reference) 
ECM Terminal Name
Between CANL and E1
Tester Range
1 V/DIV., 10 μsec./DIV.
Condition
Ignition switch ON

HINT:
The waveform varies depending on the CAN communication signal.


WAVEFORM 15
A255990E01
Terminal AID of Air Injection Control Driver 
ECM Terminal Name
Between AIDI and E1
Tester Range
5 V/DIV., 50 msec./DIV.
Condition
Performing Active Test using Techstream (Secondary Air Injection Check)

HINT:
The wavelength changes when the air injection control driver detects malfunctions in the secondary air injection system (Click here).


WAVEFORM 16
A122768E04
Crankshaft Position Sensor and VVT Sensor for Exhaust Side 
ECM Terminal Name
Between NE+ and NE-
Between EV1+ and EV1-
Between EV2+ and EV2-
Tester Range
5 V/DIV., 20 msec./DIV.
Condition
Idling

HINT:
The wavelength becomes shorter as the engine speed increases.