Home › ENGINE ยท 3UR-FBE › ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > FREEZE FRAME DATA

for Preparation Click here



DESCRIPTION
  1. Freeze frame data records the engine conditions (fuel system, calculated load, engine coolant temperature, fuel trim, engine speed, vehicle speed, etc.) when a malfunction is detected. When troubleshooting, it can help determine if the vehicle was moving or stationary, the engine was warmed up or not, the air-fuel ratio was Lean or Rich, and other data from the time the malfunction occurred.

    HINT:
    If it is impossible to duplicate the problem even though a DTC is output, confirm the freeze frame data.


  1. A103809E38
    The ECM records engine conditions in the form of freeze frame data every 0.5 seconds. Using the Techstream, 5 separate sets of freeze frame data can be checked.
    1. 3 data sets before the DTC was set.
    2. 1 data set when the DTC was set.
    3. 1 data set after the DTC was set.
    1. These data sets can be used to simulate the condition of the vehicle around the time of the occurrence of the malfunction. The data may assist in identifying the cause of the malfunction, and in judging whether it was temporary or not.

LIST OF FREEZE FRAME DATA

Tester Display
Measurement Item
Diagnostic Note
Vehicle Speed
Vehicle speed
Speed indicated on speedometer.
Engine Speed
Engine speed
-
Calculate Load
Calculated load
Calculated load by ECM.
Vehicle Load
Vehicle load
-
MAF
Mass air flow volume
If approximately 0.0 gm/sec.:
  1. Mass air flow meter power source circuit open or short.
  1. VG circuit open or short.
If 160.0 gm/sec. or more:
  1. E2G circuit open.
Atmosphere Pressure
Atmosphere pressure
-
Coolant Temp
Engine coolant temperature
If -40°C (-40°F), sensor circuit open.
If 140°C (284°F) or more, sensor circuit shorted.
Intake Air
Intake air temperature
If -40°C (-40°F), sensor circuit open.
If 140°C (284°F) or more, sensor circuit shorted.
Engine Run Time
Accumulated engine running time
-
Initial Engine Coolant Temp
Engine coolant temperature at engine start
-
Initial Intake Air Temp
Intake air temperature at engine start
-
Battery Voltage
Battery voltage
-
Glow Indicator Supported
Status of glow indicator supported
-
Glow Indicator
Glow indicator
-
Accel Sens. No. 1 Volt %
Absolute Accelerator Pedal Position (APP) No. 1
-
Accel Sens. No. 2 Volt %
Absolute APP No. 2
-
Throttle Sensor Volt %
Throttle position
-
Throttl Sensor #2 Volt %
Throttle sensor positioning #2
-
Throttle Sensor Position
Throttle sensor positioning
-
Throttle Motor DUTY
Throttle actuator
-
Throttle Position
Throttle position
For use when engine stall, starting problems or rough idle is present.
ISC Flow
Flow rate calculated using information from each sensor
For use when engine stall, starting problems or rough idle is present.
ISC Position
Requested opening amount calculated using ISC control
For use when engine stall, starting problems or rough idle is present.
ISC Feedback Value
ISC feedback compensation amount
For use when engine stall, starting problems or rough idle is present.
ISC Learning Value
ISC learned compensation amount
For use when engine stall, starting problems or rough idle is present.
Electric Load Feedback Val
Compensation flow rate according to electrical load
For use when engine stall, starting problems or rough idle is present.
Air Conditioner FB Val
Compensation flow rate according to air conditioner load
For use when engine stall, starting problems or rough idle is present.
PS Feedback Val
Compensation flow rate according to power steering load
For use when engine stall, starting problems or rough idle is present.
Low Revolution Control
Low engine speed control operation state
For use when engine stall, starting problems or rough idle is present.
N Range Status
Shift lever N status
For use when engine stall, starting problems or rough idle is present.
Eng Stall Control FB Flow
Intake air compensation flow rate
For use when engine stall, starting problems or rough idle is present.
Deposit Loss Flow
Flow loss due to deposits
For use when engine stall, starting problems or rough idle is present.
Fuel Press Switching Valve
Fuel press switching valve status
-
Injector (Port)
Injection period of No. 1 cylinder
-
Injection Volum (Cylinder 1)
Injection volume
-
Fuel Pump/Speed Status
Fuel pump/speed status
-
Vacuum Pump
Key-off EVAP system leak detection pump status
Refer to EVAP System (Click here).
Current Fuel Type
Status of the current fuel type
-
EVAP (Purge) VSV
EVAP purge VSV duty ratio
-
Evap Purge Flow
Ratio of evaporative purge flow to intake air volume
-
Purge Density Learn Value
Learning value of purge density
-
EVAP System Vent Valve
Key-off EVAP system vent valve status
-
EVAP Purge VSV
EVAP Purge VSV
-
Purge Cut VSV Duty
Purge cut VSV duty
-
Target Air-Fuel Ratio
Ratio compared to stoichiometric level
-
AF Lambda B1S1
Output air fuel ratio associated with Bank 1 Sensor 1
-
AF Lambda B2S1
Output air fuel ratio associated with Bank 2 Sensor 1
-
AFS Voltage B1S1
A/F sensor output voltage
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor.
AFS Voltage B2S1
AFS Current B1S1
A/F sensor current (for Bank 1)
-
AFS Current B2S1
A/F sensor current (for Bank 2)
-
A/F Heater Duty #1
A/F heater duty ratio (for Bank 1)
-
A/F Heater Duty #2
A/F heater duty ratio (for Bank 2)
-
O2S B1S2
Heated oxygen sensor output
Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor.
O2S B2S2
O2S Impedance B1S2
Sub heated oxygen sensor impedance (for Sensor 2)
-
O2S Impedance B2S2
O2 Heater B1S2
Heated oxygen sensor heater (for Sensor 2)
-
O2 Heater B2S2
O2 Heater Curr Val B1S2
Heated oxygen sensor current (for Sensor 2)
-
O2 Heater Curr Val B2S2
Short FT #1
Short-term fuel trim
Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio.
Long FT #1
Long-term fuel trim
Overall fuel compensation carried out in long term to compensate a continual deviation of short-term fuel trim from central value.
A/F Learn Value Idle #1
Air fuel ratio learned value for idling (for Bank 1)
-
A/F Learn Value Low #1
Air fuel ratio learned value for low engine loads (for Bank 1)
-
A/F Learn Value Mid1 #1
Air fuel ratio learned value for mid-sized engine loads 1 (for Bank 1)
-
A/F Learn Value Mid2 #1
Air fuel ratio learned value for mid-sized engine loads 2 (for Bank 1)
-
A/F Learn Value High #1
Air fuel ratio learned value for high engine loads (for Bank 1)
-
Total FT #1
Total fuel trim
-
Short FT #2
Short-term fuel trim
Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio.
Long FT #2
Long-term fuel trim
Overall fuel compensation carried out in long term to compensate a continual deviation of short-term fuel trim from central value.
A/F Learn Value Idle #2
Air fuel ratio learned value for idling (for Bank 2)
-
A/F Learn Value Low #2
Air fuel ratio learned value for low engine loads (for Bank 2)
-
A/F Learn Value Mid1 #2
Air fuel ratio learned value for mid-sized engine loads 1 (for Bank 2)
-
A/F Learn Value Mid2 #2
Air fuel ratio learned value for mid-sized engine loads 2 (for Bank 2)
-
A/F Learn Value High #2
Air fuel ratio learned value for high engine loads (for Bank 2)
-
Total FT #2
Total fuel trim
-
Fuel System Status #1
Fuel system status (for Bank 1)
  1. OL (Open Loop): Has not yet satisfied conditions to go closed loop.
  2. CL (Closed Loop): Using A/F sensor as feedback for fuel control.
  3. OL Drive: Open loop due to driving conditions (fuel enrichment).
  4. OL Fault: Open loop due to detected system fault.
  5. CL Fault: Closed loop but A/F sensor, which used for fuel control, malfunctioning.
Fuel System Status #2
Fuel system status (for Bank 2)
  1. OL (Open Loop): Has not yet satisfied conditions to go closed loop.
  2. CL (Closed Loop): Using A/F sensor as feedback for fuel control.
  3. OL Drive: Open loop due to driving conditions (fuel enrichment).
  4. OL Fault: Open loop due to detected system fault.
  5. CL Fault: Closed loop but A/F sensor, which used for fuel control, malfunctioning.
Air Pump Pressure (Absolute)
Air pump pressure (for Bank 1)
-
Air Pump2 Pressure (Absolute)
Air pump pressure (for Bank 2)
-
Air Pump Pulsation Pressure
Air pump pulsation pressure (for Bank 1)
-
Air Pump2 Pulsation Pressure
Air pump pulsation pressure (for Bank 2)
-
Secondary Air Control VSV
Secondary air injection system status
-
2nd Air System Status
Secondary air system status
-
AI Test
Secondary air injection system operation prohibit
-
Subfreezing Conditions
Subfreezing conditions status
-
Air Pump Freeze
Air pump freeze status
-
Air Pump2 Freeze
Air pump 2 freeze status
-
Air Switching Valve Freeze
Switching valve freeze status
-
Air Switching Valve2 Freeze
Switching valve 2 freeze status
-
Air Pump Heater
Air pump heater status
-
IGN Advance
Ignition advance
-
Knock Feedback Value
Feedback value of knocking
-
Knock Correct Learn Value
Correction learning value of knocking
-
Idle Spark Advn Ctrl #1
Individual cylinder timing advance compensation amount (No. 1)
For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #2
Individual cylinder timing advance compensation amount (No. 2)
For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #3
Individual cylinder timing advance compensation amount (No. 3)
For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #4
Individual cylinder timing advance compensation amount (No. 4)
For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #5
Individual cylinder timing advance compensation amount (No. 5)
For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #6
Individual cylinder timing advance compensation amount (No. 6)
For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #7
Individual cylinder timing advance compensation amount (No. 7)
For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #8
Individual cylinder timing advance compensation amount (No. 8)
For use when engine stall, starting problems or rough idle is present.
ACIS VSV
VSV for Acoustic Control Induction System (ACIS)
-
Actual VVT Angle #1
Actual VVT displacement angle (bank 1)
This item is used for freeze frame data only
Actual VVT Angle #2
Actual VVT displacement angle (bank 2)
This item is used for freeze frame data only
Actual VVT Ex Angle #1
Actual VVT exhaust displacement angle (bank 1)
This item is used for freeze frame data only
Actual VVT Ex Angle #2
Actual VVT exhaust displacement angle (bank 2)
This item is used for freeze frame data only
VVT Control Status #1
VVT control status (for Bank 1)
-
VVT Control Status #2
VVT control status (for Bank 2)
-
VVT Advance Fail
VVT control failure status
-
Catalyst Temp B1S1
Estimated catalyst temperature (for Sensor 1)
-
Catalyst Temp B2S1
Catalyst Temp B1S2
Estimated catalyst temperature (for Sensor 2)
-
Catalyst Temp B2S2
Starter Signal
Starter switch (STSW) signal
-
Starter Control
Starter switch status
-
Power Steering Signal
Power steering switch status
-
Starter Relay
Starter relay status
-
ACC Relay
ACC relay status
-
Neutral Position SW Signal
Park/Neutral position (PNP) switch signal
-
Transfer L4
Park/Neutral position (PNP) switch signal
-
Stop Light Switch
Stop light switch
-
A/C Signal
A/C signal
-
Closed Throttle Position SW
Closed throttle position switch
-
Fuel Cut Condition
Fuel cut condition
-
Immobiliser Communication
Immobiliser communication
-
TC Terminal
TC terminal status
-
Time after DTC Cleared
Cumulative time after DTC cleared
-
Distance from DTC Cleared
Accumulated distance from DTC cleared
-
Warmup Cycle Cleared DTC
Warm-up cycle after DTC cleared
-
Dist Batt Cable Disconnect
Total distance vehicle driven after battery cable disconnected
-
IG OFF Elapsed Time
Cumulative time after ignition switch off
-
TC and TE1
TC and CG (TE1) terminals of DLC3
-
Total Distance Traveled
Total distance traveled
-
Ignition Trig. Count
Ignition counter
-
Cylinder #1 Misfire Count
Cylinder #1 misfire count
-
Cylinder #2 Misfire Count
Cylinder #2 misfire count
-
Cylinder #3 Misfire Count
Cylinder #3 misfire count
-
Cylinder #4 Misfire Count
Cylinder #4 misfire count
-
Cylinder #5 Misfire Count
Cylinder #5 misfire count
-
Cylinder #6 Misfire Count
Cylinder #6 misfire count
-
Cylinder #7 Misfire Count
Cylinder #7 misfire count
-
Cylinder #8 Misfire Count
Cylinder #8 misfire count
-
All Cylinders Misfire Count
Misfire count of all cylinders
-
Multi Cylinders Misfire Count
Multiple cylinder misfire count
-
Misfire RPM
Engine speed when misfire occurred
-
Misfire Load
Engine load when misfire occurred
-
Misfire Margin
Margin to detect engine misfire
-
Catalyst OT MF F/C
Catalyst over temperature misfire prevention F/C
-
Cat OT MF F/C History
Catalyst over temperature misfire prevention F/C history
-
Cat OT MF F/C Cylinder#1
Display of fuel cut operation in No. 1 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder#2
Display of fuel cut operation in No. 2 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder#3
Display of fuel cut operation in No. 3 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder#4
Display of fuel cut operation in No. 4 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder#5
Display of fuel cut operation in No. 5 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder#6
Display of fuel cut operation in No. 6 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder#7
Display of fuel cut operation in No. 7 cylinder (if certain level of misfire malfunction is detected)
-
Cat OT MF F/C Cylinder#8
Display of fuel cut operation in No. 8 cylinder (if certain level of misfire malfunction is detected)
-
Engine Speed (Starter Off)
Engine speed when starter off
For use when engine stall, starting problems or rough idle is present.
Starter Count
Number of times starter turned on after ignition switch turned to ON
For use when engine stall, starting problems or rough idle is present.
Run Dist of Previous Trip
Distance driven during previous trip
For use when engine stall, starting problems or rough idle is present.
Engine Starting Time
Time elapsed before engine starts (after starter turns on until engine speed reaches 400 rpm)
For use when engine stall, starting problems or rough idle is present.
Previous Trip Coolant Temp
Engine coolant temperature during previous trip
For use when engine stall, starting problems or rough idle is present.
Previous Trip Intake Temp
Intake air temperature during previous trip
For use when engine stall, starting problems or rough idle is present.
Engine Oil Temperature
Engine oil temperature (estimated temperature)
For use when engine stall, starting problems or rough idle is present.
Previous Trip Eng Oil Temp
Engine oil temperature during previous trip
For use when engine stall, starting problems or rough idle is present.
Ambient Temp for A/C
Ambient temperature for A/C
For use when engine stall, starting problems or rough idle is present.
Previous Trip Ambient Temp
Ambient temperature during previous trip
For use when engine stall, starting problems or rough idle is present.
Engine Start Hesitation
History of hesitation during engine start
For use when engine stall, starting problems or rough idle is present.
Low Rev for Eng Start
History of low engine speed after engine start
For use when engine stall, starting problems or rough idle is present.
Minimum Engine Speed
Minimum engine speed
For use when engine stall, starting problems or rough idle is present.
Power Steering Pressure
Power steering pressure sensor
-
ACT VSV
A/C cut status for Active Test
-
Brake Override System
Brake override system status
-
Idle Fuel Cut
Fuel cut idle
ON: when throttle valve fully closed and engine speed over 3500 rpm.
FC TAU
Fuel cut during very light load
Fuel cut being performed under very light load to prevent engine combustion from becoming incomplete.
Immobiliser Fuel Cut
Status of the immobiliser fuel cut
-
Immobiliser Fuel Cut History
Immobiliser fuel cut history
For use when starting problems is present.
Alcohol Density Estimate
Alcohol density estimate
-
Alcohol Density Learning
Status of the alcohol density learning
-
Fuel Remaining Volume
Fuel remaining volume
-
Electrical Load Signal 1
Electrical load signal
-
Electrical Load Signal 2
Electrical load signal
-
Cruise Cancel Signal
Status of the cruise cancel signal
-
SPD (NT)
Input shaft speed
Data is displayed in increments of 50 rpm.
SPD (SP2)
Output shaft speed
-
Overdrive Cut Switch #1
Status of the overdrive cut switch
-
Shift SW Status (P Range)
Park/neutral position switch status (P)
When the shift lever position displayed on the Techstream differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
Shift SW Status (R Range)
Park/neutral position switch status (R)
When the shift lever position displayed on the Techstream differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
Shift SW Status (N Range)
Park/neutral position switch status (N)
When the shift lever position displayed on the Techstream differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
Shift SW Status (N,P Range) Supported
Status of park/neutral position switch (N or P) supported
-
Shift SW Status (N,P Range)
Park/neutral position switch status (N or P)
When the shift lever position displayed on the Techstream differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
Sports Shift Up SW
Sport shift up switch status
-
Sports Shift Down SW
Sport shift down switch status
-
Sports Mode Selection SW
Sport mode select switch status
-
Shift SW Status (D Range)
Park/neutral position switch status (D)
When the shift lever position displayed on the Techstream differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
A/T Oil Temperature 1
No. 1 ATF temperature sensor value
If the value is -40°C or 215°C, the No. 1 ATF temperature sensor circuit open or shorted.
A/T Oil Temperature 2
No. 2 ATF temperature sensor value
If the value is -40°C or 215°C, the No. 2 ATF temperature sensor circuit open or shorted.
Lock Up
Lock-up
-
Shift Status
ECM gear shift command
-
SLT Solenoid Status
Shift solenoid SLT status
-
SLU Solenoid Status
Shift solenoid SLU status
-
AT Fluid
Flex lock-up judder judgment
-