Home › ENGINE ยท 3UR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P2121    Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance

for Preparation Click here


DESCRIPTION

HINT:
Refer to DTC P2120 .


DTC Code
DTC Detection Condition
Trouble Area
P2121
Either conditions (1) or (2) met for 0.5 seconds (1 trip detection logic):
(1) Difference between VPA and VPA2 is less than 0.4 V, or more than 1.2 V. (learned value of accelerator off position)
(2) Difference between VPA and VPA2 is greater than or equal to the specified value.
  1. Accelerator Pedal Position (APP) sensor
  2. ECM

MONITOR DESCRIPTION

When the difference between the output voltages of VPA and VPA2 deviates from the standard, the ECM determines that the Accelerator Pedal Position (APP) sensor is malfunctioning. The ECM turns on the MIL and the DTC is stored.

MONITOR STRATEGY


Related DTCs
P2121: APP sensor rationality
Required Sensors/Components (Main)
APP sensor
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
-: Case 1
0.5 seconds: Case 2
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


ALL (Case 1 and Case 2) 
Monitor runs whenever following DTCs not present
P2120, P2122, P2123, P2125, P2127, P2128, P2138 (Accelerator Pedal Position sensor)
Either of following conditions 1 or 2 met:
-
1. Ignition switch
ON
2. Throttle actuator power
ON

Case 2 
VPA2 voltage
Less than 4.84 V
Either of following conditions met:
1 or 2
a) VPA voltage - Learned VPA accelerator off position voltage
0.04 V or more
b) VPA2 voltage - Learned VPA2 accelerator off position voltage
0.04 V or more

TYPICAL MALFUNCTION THRESHOLDS


Case 1 
Difference between VPA voltage and VPA2 voltage (learned value of accelerator off position)
Less than 0.4 V, or more than 1.2 V

Case 2 
All of the following conditions are met
-
(VPA voltage - Learned VPA accelerator off position voltage) - (VPA2 voltage - Learned VPA2 accelerator off position voltage)
0.165 V or more (varies with accelerator position)
VPA2 voltage
Less than 4.84 V
Either of the following conditions met
a or b
(a) VPA voltage - Learned VPA accelerator off position voltage
0.04 V or higher
(b) VPA2 voltage - Learned VPA2 accelerator off position voltage
0.04 V or higher

CONFIRMATION DRIVING PATTERN


A199317E03

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Fully depress and release the accelerator pedal [B].
  7. Check that 20 seconds or more have elapsed since the DTCs were cleared.
  8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].
  9. Read the Pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  11. Input the DTC: P2121.
  12. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit

    HINT:
    1. If the judgment result shows ABNORMAL, the system has a malfunction.
    2. If the judgment result shows INCOMPLETE or N/A, perform steps [B] and [C] again.

  13. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


FAIL-SAFE

When any of DTCs P2120, P2121, P2122, P2123, P2125, P2127, P2128 and P2138 is stored, the ECM enters fail-safe mode. If either of the 2 sensor circuits malfunctions, the ECM uses the remaining circuit to calculate the accelerator pedal position to allow the vehicle to continue driving. If both of the circuits malfunction, the ECM regards the accelerator pedal as being released. As a result, the throttle valve is closed and the engine idles.
Fail-safe mode continues until a pass condition is detected, and the ignition switch is turned off.

WIRING DIAGRAM

Refer to DTC P2120 .

INSPECTION PROCEDURE

HINT:
  1. This DTC relates to the Accelerator Pedal Position (APP) sensor.
  2. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2121)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    P2121 is output
    A
    P2121 and other DTCs are output
    B

    HINT:
    If any DTCs other than P2121 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.READ VALUE USING TECHSTREAM (ACCELERATOR POSITION SENSOR)
FI07052E06
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / ETCS / Accel Sensor Out No. 1 and Accel Sensor Out No. 2.

  1. Read the values displayed on the Techstream.

    Standard voltage:
    Accelerator Pedal Operations
    Accel Sensor Out No. 1
    Accel Sensor Out No. 2
    Released
    0.5 to 1.1 V
    1.2 to 2.0 V
    Depressed
    2.6 to 4.5 V
    3.4 to 4.75 V



NG
Go to step 3
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

3.REPLACE ACCELERATOR PEDAL ASSEMBLY
  1. Replace the accelerator pedal assembly (Click here).


NEXT


4.CHECK WHETHER DTC OUTPUT RECURS (DTC P2121)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Start the engine.

  1. Allow the engine to idle for 15 seconds.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.
    Result 
    Result
    Proceed to
    P2121 is output
    A
    No DTC is output
    B



B
SYSTEM OK
A

REPLACE ECM (Click here)