Home › ENGINE ยท 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0630    VIN not Programmed or Mismatch - ECM / PCM

for Preparation Click here


DESCRIPTION

DTC P0630 is stored when the Vehicle Identification Number (VIN) is not stored in the ECM, or the input VIN is incorrect. The VIN is input with the Techstream.

DTC No.
DTC Detection Condition
Trouble Area
P0630
Either condition is met (1 trip detection logic):
  1. VIN is not stored in the ECM.
  2. Input VIN is incorrect.
ECM

MONITOR STRATEGY


Related DTCs
P0630: VIN not programmed
Required Sensors/Components (Main)
ECM
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
0.325 seconds
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Battery voltage
8 V or higher
Ignition switch
ON
Starter
OFF

TYPICAL MALFUNCTION THRESHOLDS


VIN code
Not programmed

COMPONENT OPERATING RANGE


VIN code
Programmed

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on.
  6. Wait 5 seconds or more.
  7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
  8. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  9. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  10. Input the DTC: P0630.
  11. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    If the judgment result shows ABNORMAL, the system has a malfunction.

  12. If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


INSPECTION PROCEDURE

HINT:
Read freeze frame data using a Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ CURRENT DTC
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    P0630 is output
    A
    P0630 and other DTCs are output
    B

    HINT:
    If any DTCs other than P0630 are output, troubleshoot those DTCs first.

    NOTICE:
    If P0630 is stored, the VIN must be input to the ECM using the Techstream. However, DTCs are cleared automatically by the Techstream when the VIN is input. If DTCs other than P0630 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.INPUT VIN WITH TECHSTREAM
  1. Refer to Registration (Click here).


NEXT

END