Home › BRAKE › BRAKE CONTROL › STEERING ANGLE SENSOR

STEERING ANGLE SENSOR > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



3. PLACE FRONT WHEELS FACING STRAIGHT AHEAD


4. REMOVE LOWER NO. 3 STEERING WHEEL COVER


    B355134E01
  1. Using a screwdriver, detach the claw and guide and remove the lower No. 3 steering wheel cover.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.



5. REMOVE LOWER NO. 2 STEERING WHEEL COVER


    B355135E01
  1. w/ Cruise Control:
    Text in Illustration 
    *1
    Protective Tape

    1. Using a screwdriver, detach the claw and guide and remove the lower No. 2 steering wheel cover.

      HINT:
      Tape the screwdriver tip before use.



    B356800E01
  1. w/o Cruise Control:
    Text in Illustration 
    *1
    Protective Tape

    1. Using a screwdriver, detach the claw and guide and remove the lower No. 2 steering wheel cover.

      HINT:
      Tape the screwdriver tip before use.



6. REMOVE STEERING PAD

CAUTION:
When storing the steering pad, keep the airbag deployment side facing upward.

  1. Check that the ignition switch is off.

  1. Check that the cable is disconnected from the negative (-) battery terminal.

    NOTICE:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



    B356583
  1. Using a T30 "TORX" socket wrench, loosen the 2 screws until the groove along the screw circumference catches on the screw case.

  1. Pull the steering pad toward you.



    B354949E01
  1. Disconnect the horn connector from the steering pad.

  1. Using a screwdriver, release the 2 airbag connector locks.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape

  1. Disconnect the 2 airbag connectors and remove the steering pad as shown in the illustration.

    NOTICE:
    When disconnecting any airbag connector, take care not to damage the airbag wire harness.



7. REMOVE STEERING WHEEL ASSEMBLY
  1. Remove the steering wheel set nut.



    C290066E01
  1. Put matchmarks on the steering wheel and main shaft.
    Text in Illustration 
    *a
    Matchmark
    *b
    Hold
    *c
    Turn

  1. Using SST, remove the steering wheel.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05011)



8. REMOVE LOWER STEERING COLUMN COVER


    C290067
  1. Remove the 2 screws.

  1. Detach the 2 claws to remove the lower steering column cover.



9. REMOVE UPPER STEERING COLUMN COVER


    C290068
  1. Detach the 4 clips.

  1. Detach the claw to remove the upper steering column cover.



10. REMOVE SPIRAL CABLE SUB-ASSEMBLY


    B166448
  1. Disconnect the connectors from the spiral cable sub-assembly with steering sensor.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Detach the 3 claws and remove the spiral cable sub-assembly with steering sensor.

    NOTICE:
    1. Do not replace the spiral cable sub-assembly when the ignition switch is ON and the battery cable is connected.
    2. Do not rotate the spiral cable sub-assembly when the ignition switch is ON and the battery cable is connected.
    3. Make sure the steering wheel is installed and centered before rotating the steering sensor when performing steering angle sensor operation inspections (inspecting for abnormal noise, diagnosis inspections, etc.).
    4. Do not remove the steering sensor from the spiral cable sub-assembly.



11. REMOVE STEERING ANGLE SENSOR


    B166448
  1. Disconnect the connectors from the spiral cable sub-assembly with steering sensor.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Detach the 3 claws and remove the spiral cable sub-assembly with steering sensor.

    NOTICE:
    1. Do not replace the spiral cable sub-assembly when the ignition switch is ON and the battery cable is connected.
    2. Do not rotate the spiral cable sub-assembly when the ignition switch is ON and the battery cable is connected.
    3. Make sure the steering wheel is installed and centered before rotating the steering sensor when performing steering angle sensor operation inspections (inspecting for abnormal noise, diagnosis inspections, etc.).
    4. Do not remove the steering sensor from the spiral cable sub-assembly.