DTC P0327 Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor) |
DTC P0328 Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor) |
DTC P0332 Knock Sensor 2 Circuit Low Input (Bank 2) |
DTC P0333 Knock Sensor 2 Circuit High Input (Bank 2) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0327 P0332 | Output voltage of the knock sensor is below 0.5 V (1 trip detection logic). |
|
| P0328 P0333 | Output voltage of the knock sensor is higher than 4.5 V (1 trip detection logic). |
|

| Item | Content |
| Terminal | KNK1 - EKNK KNK2 - EKN2 |
| Equipment Setting | 1 V/DIV. 0.01 to 1 msec./DIV. |
| Condition | Engine speed at 4000 rpm with warm engine |
| Related DTCs | P0327: Knock sensor (bank 1) range check (Low voltage) P0328: Knock sensor (bank 1) range check (High voltage) P0332: Knock sensor (bank 2) range check (Low voltage) P0333: Knock sensor (bank 2) range check (High voltage) |
| Required Sensors/Components (Main) | Knock sensor |
| Required Sensors/Components (Related) | - |
| Frequency of Operation | Continuous |
| Duration | 1 second |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not stored | None |
| Battery voltage | 10.5 V or higher |
| Time after engine start | 5 seconds or more |
| Ignition switch | ON |
| Starter | OFF |
| Knock sensor voltage | Below 0.5 V |
| Knock sensor voltage | Higher than 4.5 V |
| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.CHECK KNOCK SENSOR |
![]() |
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D74-94 (KNK1) - D74-93 (EKNK) | 20°C (68°F) | 120 to 280 kΩ |
| D74-117 (KNK2) - D74-116 (EKN2) | 20°C (68°F) | 120 to 280 kΩ |
| *a | Rear view of wire harness connector (to ECM) |
|
| ||||
| OK | |
| 2.CHECK TERMINAL VOLTAGE (ECM) |
![]() |
Disconnect the Da2 connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| Da2 female connector 2 - 5 | Ignition switch ON | 4.5 to 5.5 V |
| Da2 female connector 4 - 6 | Ignition switch ON | 4.5 to 5.5 V |
| *1 | Female |
| *a | Front view of wire harness connector (to ECM Wire) |
|
| ||||
| OK | ||
| ||
| 3.CHECK HARNESS AND CONNECTOR (KNOCK SENSOR - ECM) |
Disconnect the knock sensor connectors.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| a2-2 - D74-94 (KNK1) | Always | Below 1 Ω |
| a2-1 - D74-93 (EKNK) | Always | Below 1 Ω |
| a1-2 - D74-117 (KNK2) | Always | Below 1 Ω |
| a1-1 - D74-116 (EKN2) | Always | Below 1 Ω |
| a2-2 or D74-94 (KNK1) - Body ground | Always | 10 kΩ or higher |
| a2-1 or D74-93 (EKNK) - Body ground | Always | 10 kΩ or higher |
| a1-2 or D74-117 (KNK2) - Body ground | Always | 10 kΩ or higher |
| a1-1 or D74-116 (EKN2) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||