DTC P0441 Evaporative Emission Control System Incorrect Purge Flow |
| DTC No. | Monitoring Item | Malfunction Detection Condition | Trouble Area | Detection Timing | Detection Logic |
| P0441 | Purge VSV (Vacuum Switching Valve) stuck open | Leak detection pump creates negative pressure (vacuum) in the EVAP system and the EVAP system pressure is measured. Reference pressure is measured at the start and end of the leak check. If the stabilized pressure is higher than [second reference pressure x 0.2], the ECM determines that the purge VSV is stuck open. |
| While ignition switch off | 2 trip |
| Purge VSV stuck closed | After the EVAP leak check is performed, the purge VSV is turned ON (open) and outside air is introduced into the EVAP system. Reference pressure is measured at the start and end of the check. If the pressure does not return to near atmospheric pressure, the ECM determines that the purge VSV is stuck closed. |
| While ignition switch off | 2 trip | |
| Purge flow | While the engine is running, the following conditions are successively met:
|
| While engine running | 2 trip |
| Sequence | Operation | Description | Duration |
| - | ECM activation | Activated by soak timer 5, 7 or 9.5 hours after ignition switch turned off. | - |
| A | Atmospheric pressure measurement | Vent valve turned OFF (vent) and EVAP system pressure measured by ECM in order to register atmospheric pressure. If pressure in EVAP system not between 70 kPa-a and 110 kPa-a (525 mmHg-a and 825 mmHg-a), ECM cancels EVAP system monitor. | 60 seconds |
| B | First reference pressure measurement | In order to determine reference pressure, leak detection pump creates negative pressure (vacuum) through reference orifice, and then ECM checks if leak detection pump and vent valve operate normally. | 360 seconds |
| C | EVAP system pressure measurement | Vent valve turned ON (closed) to shut EVAP system. Negative pressure (vacuum) created in EVAP system, and EVAP system pressure then measured. Write down measured value as it will be used in leak check. If EVAP pressure does not stabilize within 15 minutes, ECM cancels EVAP system monitor. | 15 minutes* |
| D | Purge VSV monitor | Purge VSV opened, and then EVAP system pressure measured by ECM. Large increase indicates normality. | 10 seconds |
| E | Second reference pressure measurement | After second reference pressure measurement, leak check performed by comparing first and second reference pressure measurements. If stabilized system pressure higher than second reference pressure, ECM determines that EVAP system leaking. | 60 seconds |
| - | Final check | Atmospheric pressure measured, and then monitoring result recorded by ECM. | - |




| Related DTCs | P0441: Purge VSV stuck open/closed P0441: Purge flow |
| Required Sensors/Components | Purge VSV Canister pump module |
| Frequency of Operation | Once per driving cycle |
| Duration | Within 20 minutes (varies with amount of fuel in tank): Purge VSV stuck open/closed Within 30 seconds: Purge flow |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not stored | P0452, P0453 (EVAP system) |
| Atmospheric pressure | 70 to 110 kPa-a (525 to 825 mmHg-a) |
| Battery voltage | 10.5 V or higher |
| Vehicle speed | Less than 4 km/h (2.5 mph) |
| Ignition switch | Off |
| Time after key-off | 5, 7 or 9.5 hours |
| Purge VSV | Not operated by scan tool |
| Vent valve | Not operated by scan tool |
| Leak detection pump | Not operated by scan tool |
| Both of following conditions met before key-off | Conditions 1 and 2 |
| 1. Duration that vehicle driven | 5 minutes or more |
| 2. EVAP purge operation | Performed |
| Engine coolant temperature | 4.4 to 35°C (40 to 95°F) |
| Intake air temperature | 4.4 to 35°C (40 to 95°F) |
| Engine | Running |
| Engine coolant temperature | 4.4°C (40°F) or higher |
| Intake air temperature | 4.4°C (40°F) or higher |
| Purge VSV | Not operated by scan tool |
| EVAP system check | Not operated by scan tool |
| Atmospheric pressure | 76 to 111 kPa-a (570 to 835 mmHg-a) |
| Battery voltage | 10 V or higher |
| Purge duty cycle | 8% or more |
| EVAP pressure when vacuum introduction complete | Reference pressure x 0.2 or higher |
| EVAP pressure change after purge VSV ON (open) | Less than 0.3 kPa-g (2.25 mmHg-g) |
| Both of following conditions met | Conditions 1 and 2 |
| 1. EVAP pressure change when purge operation started | Less than 0.1 kPa-g (0.75 mmHg-g) |
| 2. EVAP pressure change during purge operation when vent valve closed | Less than 0.15 kPa-g (1.12 mmHg-g) |
| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|