DTC P0136 Oxygen Sensor Circuit Malfunction (Bank 1 Sensor 2) |
DTC P0137 Oxygen Sensor Circuit Low Voltage (Bank 1 Sensor 2) |
DTC P0138 Oxygen Sensor Circuit High Voltage (Bank 1 Sensor 2) |
DTC P0139 Oxygen Sensor Circuit Slow Response (Bank 1 Sensor 2) |
DTC P013A Oxygen Sensor Slow Response - Rich to Lean Bank 1 Sensor 2 |
DTC P013C Oxygen Sensor Slow Response - Rich to Lean Bank 2 Sensor 2 |
DTC P0156 Oxygen Sensor Circuit Malfunction (Bank 2 Sensor 2) |
DTC P0157 Oxygen Sensor Circuit Low Voltage (Bank 2 Sensor 2) |
DTC P0158 Oxygen Sensor Circuit High Voltage (Bank 2 Sensor 2) |
DTC P0159 Oxygen Sensor Circuit Slow Response (Bank 2 Sensor 2) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0136 P0156 | Either condition is met:
|
|
| P0137 P0157 | Either condition is met:
|
|
| P0138 P0158 | Extremely high voltage (short): Heated oxygen sensor voltage output is higher than 1.2 V for more than 10 seconds (2 trip detection logic). |
|
| P0139 P0159 | Heated oxygen sensor voltage does not drop below 0.2 V immediately after fuel cut starts (2 trip detection logic). |
|
| P013A P013C | Heated oxygen sensor voltage does not drop from 0.35 V to 0.2 V immediately after fuel cut starts (1 trip detection logic). |
|



| Related DTCs | P0136: Heated oxygen sensor (for Bank 1) output voltage (Abnormal voltage output) P0136: Heated oxygen sensor (for Bank 1) impedance (Low) P0137: Heated oxygen sensor (for Bank 1) output voltage (Low voltage) P0137: Heated oxygen sensor (for Bank 1) impedance (High) P0138: Heated oxygen sensor (for Bank 1) output voltage (Extremely high) P0139: Heated oxygen sensor output voltage during fuel cut (for Bank 1) P013A: Heated oxygen sensor response rate during fuel cut from rich condition P013C: Heated oxygen sensor response rate during fuel cut from rich condition P0156: Heated oxygen sensor (for Bank 2) output voltage (Abnormal voltage output) P0156: Heated oxygen sensor (for Bank 2) impedance (Low) P0157: Heated oxygen sensor (for Bank 2) output voltage (Low voltage) P0157: Heated oxygen sensor (for Bank 2) impedance (High) P0158: Heated oxygen sensor (for Bank 2) output voltage (Extremely high) P0159: Heated oxygen sensor output voltage during fuel cut (for Bank 2) |
| Required Sensors/Components (Main) | Heated oxygen sensor |
| Required Sensors/Components (Related) | Crankshaft position sensor, engine coolant temperature sensor, mass air flow meter, throttle position sensor and air fuel ratio sensor |
| Frequency of Operation | Once per driving cycle: Active air-fuel ratio control detection, heated oxygen sensor abnormal voltage during fuel cut Continuous: Other |
| Duration | 20 seconds: Active air-fuel ratio control detection 90 seconds: Heated oxygen sensor impedance (High) 30 seconds: Heated oxygen sensor impedance (Low) 10 seconds: Heated oxygen sensor output voltage (Stuck high) 7 seconds: Heated oxygen sensor voltage (During fuel cut) 7 seconds: Heated oxygen sensor response rate during fuel cut from rich condition |
| MIL Operation | 2 driving cycles: P0136, P0137, P0138, P0139, P0156, P0157, P0158 and P0159 1 driving cycles: P013A and P013C |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not stored | P0016, P0018 (VVT system - Misalignment) P0017, P0019 (Exhaust VVT system - Misalignment) P0031, P0032, P0051, P0052, P101D, P103D (Air fuel ratio sensor heater) P0037, P0038, P0057, P0058, P102D, P105D (Rear oxygen sensor heater) P0102, P0103 (Mass air flow meter) P0112, P0113 (Intake air temperature sensor) P0115, P0117, P0118 (Engine coolant temperature sensor) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor) P0125 (Insufficient coolant temperature for closed loop fuel control) P0128 (Thermostat) P0171, P0172, P0174, P0175 (Fuel system) P0301 - P0306 (Misfire) P0335 (Crankshaft position sensor) P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor) P0412, P0418, P1613 (Secondary air injection system control) P0451, P0452, P0453 (EVAP system) P0500, P0722 (Vehicle speed sensor) P014C, P014D, P014E, P014F, P015A, P015B, P015C, P015D, P2195, P2196, P2197, P2198, P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256 (Air fuel ratio sensor) P0416, P0417, P2440, P2441, P2442, P2443, P2444, P2445 (Secondary air injection system) P219A, P219B (Air-Fuel Ratio Imbalance) |
| Catalyst monitor precondition | Met |
| Catalyst monitor precondition defined as when all of following conditions met: | - |
| Battery voltage | 11 V or higher |
| Intake air temperature | -10°C (14°F) or higher |
| Engine coolant temperature | 75°C (167°F) or higher |
| Atmospheric pressure | 76 kPa-a (570 mmHg-a) or higher |
| Idling | OFF |
| Engine speed | Less than 3200 rpm |
| Air fuel ratio sensor status | Activated |
| Fuel system status | Closed loop |
| Engine load | 10 to 80% |
| Shift position | 4th or higher |
| Battery voltage | 11 V or higher |
| Estimated rear heated oxygen sensor temperature | Below 700°C (1292°F) |
| ECM monitor | Completed |
| DTC P0607 | Not stored |
| Battery voltage | 11 V or higher |
| Estimated rear heated oxygen sensor temperature | 520 to 750°C (968 to 1382°F) |
| ECM monitor | Completed |
| DTC P0607 | Not stored |
| Battery voltage | 11 V or higher |
| Time after engine start | 2 seconds or more |
| Engine coolant temperature | 75°C (167°F) or higher |
| Estimated catalyst temperature | 400°C (752°F) or higher |
| Fuel cut | ON |
| Battery voltage | 11 V or higher |
| Engine coolant temperature | 75°C (167°F) or higher |
| Estimated catalyst temperature | 400°C (752°F) or higher |
| Fuel cut | ON |
| All of following conditions (a), (b) and (c) met | - |
| (a) Commanded air-fuel ratio | 14.3 or less |
| (b) Rear heated oxygen sensor voltage | 0.21 to 0.66 V |
| (c) Oxygen Storage Capacity (OSC) | 2 g or more |
| All of following conditions (a), (b) and (c) met | - |
| (a) Commanded air-fuel ratio | 14.3 or less |
| (b) Rear heated oxygen sensor voltage | Below 0.21 V |
| (c) Oxygen Storage Capacity (OSC) | 2 g or more |
| Duration following condition met | 30 seconds or more |
| Heated oxygen sensor impedance | Below 5 Ω |
| Duration following condition met | 90 seconds or more |
| Heated oxygen sensor impedance | 15 kΩ or higher |
| Duration following condition met | 10 seconds or more |
| Heated oxygen sensor voltage | 1.2 V or higher |
| Total airflow volume reached after start of fuel-cut while rear heated oxygen sensor voltage remains at 0.2 V or higher | More than 14 g |
| Duration that heated oxygen sensor voltage drops from 0.35 to 0.2 V during fuel cut (Normalized) | 0.5 second or more |
| Duration following condition met | 30 seconds or more |
| Heated oxygen sensor voltage | Varies between 0.1 and 0.9 V |

| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| Techstream Display (Sensor) | Injection Volume | Status | Voltage |
| AFS Voltage B1S1 or AFS Voltage B2S1 (A/F) | 12.5% | Rich | Less than 3.1 V |
| AFS Voltage B1S1 or AFS Voltage B2S1 (A/F) | -12.5% | Lean | More than 3.4 V |
| O2S B1S2 or O2S B2S2 (HO2) | 12.5% | Rich | More than 0.55 V |
| O2S B1S2 or O2S B2S2 (HO2) | -12.5% | Lean | Less than 0.4 V |
| Case | A/F Sensor (Sensor 1) Output Voltage | HO2 Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Area |
| 1 | ![]() ![]() | ![]() ![]() | - |
| 2 | ![]() ![]() | ![]() ![]() |
|
| 3 | ![]() ![]() | ![]() ![]() |
|
| 4 | ![]() ![]() | ![]() ![]() |
|
| 1.READ OUTPUT DTC |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| P0138 or P0158 is output | A |
| P0137 or P0157 is output | B |
| P0136 or P0156 is output | C |
| P0139, P013A, P013C or P0159 is output | D |
| P0136, P0137, P0138, P0156, P0157 or P0158 and other DTCs are output | E |
|
| ||||
|
| ||||
|
| ||||
|
| ||||
| A | |
| 2.INSPECT HEATED OXYGEN SENSOR (CHECK FOR SHORT) |
Disconnect the heated oxygen sensor connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 2 (+B) - 3 (OX1B) | Always | 10 kΩ or higher |
| 2 (+B) - 3 (OX2B) | Always | 10 kΩ or higher |
| 2 (+B) - 4 (E2) | Always | 10 kΩ or higher |
| *A | for Bank 1 Sensor 2 |
| *B | for Bank 2 Sensor 2 |
| *a | Component without harness connected (Heated Oxygen Sensor) |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT) |
Turn the ignition switch off and wait for 5 minutes.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D74-45 (HT1B) - D74-114 (OX1B) | Always | 10 kΩ or higher |
| D74-44 (HT2B) - D74-112 (OX2B) | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 4.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INJECTION VOLUME FOR A/F SENSOR) |
Connect the Techstream to the DLC3.
Start the engine.
Turn the Techstream on.
Warm up the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / Data List / O2S B1S2 or O2S B2S2.
Change the fuel injection volume using the Techstream while monitoring the voltage output of the heated oxygen sensors displayed on the Techstream.
|
| ||||
| OK | |
| 5.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INJECTION VOLUME FOR A/F SENSOR) |
Connect the Techstream to the DLC3.
Turn the Techstream on.
Start the engine.
Warm up the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.
Change the fuel injection volume using the Techstream and monitor the voltage output of the air fuel ratio and heated oxygen sensors displayed on the Techstream.
| Techstream Display (Sensor) | Voltage Variation | Proceed to |
| AFS Voltage B1S1 AFS Voltage B2S1 | Alternates between higher than and below 3.3 V | OK |
| Remains higher than 3.3 V | NG | |
| Remains below 3.3 V | NG |

|
| ||||
| OK | ||
| ||
| 6.CHECK FOR EXHAUST GAS LEAK |
Check for exhaust gas leakage.
|
| ||||
| OK | |
| 7.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE) |
Inspect the heated oxygen sensor (Click here).
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM) |
Disconnect the heated oxygen sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D31-1 (HT1B) - D74-45 (HT1B) | Always | Below 1 Ω |
| D31-3 (OX1B) - D74-114 (OX1B) | Always | Below 1 Ω |
| D31-4 (E2) - D74-115 (EX1B) | Always | Below 1 Ω |
| D32-1 (HT2B) - D74-44 (HT2B) | Always | Below 1 Ω |
| D32-3 (OX2B) - D74-112 (OX2B) | Always | Below 1 Ω |
| D32-4 (E2) - D74-113 (EX2B) | Always | Below 1 Ω |
| D31-1 (HT1B) or D74-45 (HT1B) - Body ground | Always | 10 kΩ or higher |
| D31-3 (OX1B) or D74-114 (OX1B) - Body ground | Always | 10 kΩ or higher |
| D32-1 (HT2B) or D74-44 (HT2B) - Body ground | Always | 10 kΩ or higher |
| D32-3 (OX2B) or D74-112 (OX2B) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 9.REPLACE HEATED OXYGEN SENSOR |
Replace the heated oxygen sensor (Click here).
| NEXT | |
| 10.PERFORM CONFIRMATION DRIVING PATTERN |
Perform Confirmation Driving Pattern (P0136, P0137, P0138, P0156, P0157 and P0158).
| NEXT | |
| 11.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137, P0138, P0156, P0157 OR P0158) |
Connect the Techstream to the DLC3.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0136, P0137, P0138, P0156, P0157 or P0158.
Check that the DTC monitor is NORMAL. If the DTC monitor is INCOMPLETE, perform the driving pattern again but increase the vehicle speed.
| Result | Proceed to |
| ABNORMAL (P0136, P0137, P0138, P0156, P0157 or P0158 is output) | A |
| NORMAL (No DTC is output) | B |
|
| ||||
| A | ||
| ||
| 12.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 13.PERFORM CONFIRMATION DRIVING PATTERN |
Perform Confirmation Driving Pattern (P0136, P0137, P0138, P0156, P0157 and P0158).
| NEXT | |
| 14.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136, P0137, P0138, P0156, P0157 OR P0158) |
Connect the Techstream to the DLC3.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0136, P0137, P0138, P0156, P0157 or P0158.
Check that the DTC monitor is NORMAL. If the DTC monitor is INCOMPLETE, perform the driving pattern again but increase the vehicle speed.
| Result | Proceed to |
| ABNORMAL (P0136, P0137, P0138, P0156, P0157 or P0158 is output) | A |
| NORMAL (No DTC is output) | B |
|
| ||||
| A | ||
| ||
| 15.CHECK FOR EXHAUST GAS LEAK |
Check for exhaust gas leak.
|
| ||||
| OK | |
| 16.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT) |
Turn the ignition switch off and wait for 5 minutes.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D74-45 (HT1B) - D74-114 (OX1B) | Always | 10 kΩ or higher |
| D74-44 (HT2B) - D74-112 (OX2B) | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 17.PERFORM CONFIRMATION DRIVING PATTERN |
Perform Confirmation Driving Pattern (P0139, P013A, P013C and P0159).
| NEXT | |
| 18.READ DTC OUTPUT (P0139, P013A, P013C OR P0159 IS OUTPUT AGAIN) |
Connect the Techstream to the DLC3.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0139, P013A, P013C and P0159.
Check that the DTC monitor is NORMAL. If the DTC monitor is INCOMPLETE, perform the driving pattern again but increase the vehicle speed.
| Result | Proceed to |
| ABNORMAL (P0139, P013A, P013C OR P0159 is output) | A |
| NORMAL (No DTC is output) | B |
|
| ||||
| A | ||
| ||