Home › BODY › MIRROR › OUTER REAR VIEW MIRROR

OUTER REAR VIEW MIRROR > INSPECTION

for Preparation Click here



1. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (for Standard)


    B166373E03
  1. Check the outer mirror motor operation.

    1. Apply battery voltage and check operation of the mirror face.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 10 (MV)
      Battery negative (-) → Terminal 11 (M+)
      Turns upward (A)
      Battery positive (+) → Terminal 11 (M+)
      Battery negative (-) → Terminal 10 (MV)
      Turns downward (B)
      Battery positive (+) → Terminal 12 (MH)
      Battery negative (-) → Terminal 11 (M+)
      Turns left (C)
      Battery positive (+) → Terminal 11 (M+)
      Battery negative (-) → Terminal 12 (MH)
      Turns right (D)

      Text in Illustration 
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly LH)
      If the result is not as specified, replace the outer rear view mirror assembly LH.



    B166374E03
  1. w/ Retract Mirror:
    Check the retractable mirror's movement.

    1. For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror's movement.

      OK:

      Measurement Condition
      Mirror Position
      Specified Condition
      Battery positive (+) → Terminal 7 (MR)
      Battery negative (-) → Terminal 8 (MF)
      Forward position (A)
      Moves from (A) to retracted position (E)
      Battery positive (+) → Terminal 8 (MF)
      Battery negative (-) → Terminal 7 (MR)
      Forward position (A)
      Does not move
      Battery positive (+) → Terminal 7 (MR)
      Battery negative (-) → Terminal 8 (MF)
      Position between forward position (A) and driving position (C)
      Moves from (B) to retracted position (E)
      Battery positive (+) → Terminal 8 (MF)
      Battery negative (-) → Terminal 7 (MR)
      Position between forward position (A) and driving position (C)
      Moves from (B) to forward position (A)
      Battery positive (+) → Terminal 7 (MR)
      Battery negative (-) → Terminal 8 (MF)
      Driving position (C)
      Moves from (C) to retracted position (E)
      Battery positive (+) → Terminal 8 (MF)
      Battery negative (-) → Terminal 7 (MR)
      Driving position (C)
      Does not move
      Battery positive (+) → Terminal 7 (MR)
      Battery negative (-) → Terminal 8 (MF)
      Position between driving position (C) and retracted position (E)
      Moves from (D) to retracted position (E)
      Battery positive (+) → Terminal 8 (MF)
      Battery negative (-) → Terminal 7 (MR)
      Position between driving position (C) and retracted position (E)
      Moves from (D) to driving position (C)
      Battery positive (+) → Terminal 7 (MR)
      Battery negative (-) → Terminal 8 (MF)
      Retracted position (E)
      Does not move
      Battery positive (+) → Terminal 8 (MF)
      Battery negative (-) → Terminal 7 (MR)
      Retracted position (E)
      Moves from (E) to driving position (C)

      NOTICE:
      1. Disconnect and reconnect the battery between each mirror position check.
      1. Do not apply battery voltage when moving the mirror by hand into each mirror position.

      Text in Illustration 
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly LH)
      If the result is not as specified, replace the outer rear view mirror assembly LH.



    B166835E04
  1. w/ EC Mirror:
    Check the EC mirror operation.

    NOTICE:
    Do not apply a voltage of 1.5 V or higher.


    1. Connect a 1.5 V dry-cell battery.

    2. Apply 1.5 V dry-cell battery voltage and check operation of the mirror face as shown in the table and illustration.

      OK:
      Tester Connection
      Specified Condition
      1.5 V dry-cell battery positive (+) → Terminal 14 (EC+)
      1.5 V dry-cell battery negative (-) → Terminal 13 (EC-)
      Mirror surface becomes dark

      Text in Illustration 
      *a
      Bright
      *b
      Dark
      *c
      Component without harness connected
      (Outer Rear View Mirror Assembly LH)
      If the result is not as specified, replace the outer rear view mirror assembly LH.



    B166381E03
  1. w/ Outer Mirror Light:
    Check the door mirror foot light.

    1. Apply battery voltage to the terminals of the connector, and check the illumination condition.

      OK:
      Tester Connection
      Specified Condition
      Battery positive (+) → Terminal 6 (MLP)
      Battery negative (-) → Terminal 5 (MLP-)
      Door mirror foot light illuminates

      Text in Illustration 
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly LH)
      If the result is not as specified, replace the outer mirror light assembly LH.



    B166375E05
  1. w/ Mirror Heater:
    Check the mirror heater.

    1. Apply battery voltage and check the operation of the mirror heater.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 1 (+)
      Battery negative (-) → Terminal 2 (-)
      Mirror becomes warm

      Text in Illustration 
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly LH)

      HINT:
      It will take a short time for the mirror to become warm.

      If the result is not as specified, replace the outer rear view mirror assembly LH.



2. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (for Extended Type)


    B166365E02
  1. Check the outer mirror motor operation.

    1. Apply battery voltage and check operation of the mirror face.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 10 (MV)
      Battery negative (-) → Terminal 11 (M+)
      Turns upward (A)
      Battery positive (+) → Terminal 11 (M+)
      Battery negative (-) → Terminal 10 (MV)
      Turns downward (B)
      Battery positive (+) → Terminal 12 (MH)
      Battery negative (-) → Terminal 11 (M+)
      Turns right (D)
      Battery positive (+) → Terminal 11 (M+)
      Battery negative (-) → Terminal 12 (MH)
      Turns left (C)

      Text in Illustration 
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly LH)
      If the result is not as specified, replace the outer rear view mirror assembly LH.



    B166831E04
  1. Check the door mirror turn indicator.

    1. Apply battery voltage to the terminals of the connector, and check the LED illumination condition.

      OK:
      Tester Connection
      Specified Condition
      Battery positive (+) → Terminal 4 (TRNL)
      Battery negative (-) → Terminal 3 (GND)
      Door mirror turn indicator illuminates

      Text in Illustration 
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly LH)
      If the result is not as specified, replace the outer rear view mirror assembly LH.



    B166833E03
  1. w/ Running Light:
    Check the running Light.

    1. Apply battery voltage to the terminals of the connector, and check the LED illumination condition.

      OK:
      Tester Connection
      Specified Condition
      Battery positive (+) → Terminal 9 (RL)
      Battery negative (-) → Terminal 3 (GND)
      Running light illuminates

      Text in Illustration 
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly LH)
      If the result is not as specified, replace the outer rear view mirror assembly LH.



  1. Check the mirror heater.



      B166366E03
    1. Apply battery voltage and check the operation of the mirror heater.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 1 (+)
      Battery negative (-) → Terminal 2 (-)
      Mirror becomes warm

      Text in Illustration 
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly LH)

      HINT:
      It will take a short time for the mirror to become warm.

      If the result is not as specified, replace the outer rear view mirror assembly LH.



3. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (for Standard)


    B166376E04
  1. Check the outer mirror motor operation.

    1. Apply battery voltage and check operation of the mirror face.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 10 (MV)
      Battery negative (-) → Terminal 11 (M+)
      Turns upward (A)
      Battery positive (+) → Terminal 11 (M+)
      Battery negative (-) → Terminal 10 (MV)
      Turns downward (B)
      Battery positive (+) → Terminal 12 (MH)
      Battery negative (-) → Terminal 11 (M+)
      Turns right (D)
      Battery positive (+) → Terminal 11 (M+)
      Battery negative (-) → Terminal 12 (MH)
      Turns left (C)

      Text in Illustration 
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly RH)
      If the result is not as specified, replace the outer rear view mirror assembly RH.



    B166377E04
  1. w/ Retract Mirror:
    Check the retractable mirror's movement.

    1. For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror's movement.

      OK:

      Measurement Condition
      Mirror Position
      Specified Condition
      Battery positive (+) → Terminal 7 (MR)
      Battery negative (-) → Terminal 8 (MF)
      Forward position (A)
      Moves from (A) to retracted position (E)
      Battery positive (+) → Terminal 8 (MF)
      Battery negative (-) → Terminal 7 (MR)
      Forward position (A)
      Does not move
      Battery positive (+) → Terminal 7 (MR)
      Battery negative (-) → Terminal 8 (MF)
      Position between forward position (A) and driving position (C)
      Moves from (B) to retracted position (E)
      Battery positive (+) → Terminal 8 (MF)
      Battery negative (-) → Terminal 7 (MR)
      Position between forward position (A) and driving position (C)
      Moves from (B) to forward position (A)
      Battery positive (+) → Terminal 7 (MR)
      Battery negative (-) → Terminal 8 (MF)
      Driving position (C)
      Moves from (C) to retracted position (E)
      Battery positive (+) → Terminal 8 (MF)
      Battery negative (-) → Terminal 7 (MR)
      Driving position (C)
      Does not move
      Battery positive (+) → Terminal 7 (MR)
      Battery negative (-) → Terminal 8 (MF)
      Position between driving position (C) and retracted position (E)
      Moves from (D) to retracted position (E)
      Battery positive (+) → Terminal 8 (MF)
      Battery negative (-) → Terminal 7 (MR)
      Position between driving position (C) and retracted position (E)
      Moves from (D) to driving position (C)
      Battery positive (+) → Terminal 7 (MR)
      Battery negative (-) → Terminal 8 (MF)
      Retracted position (E)
      Does not move
      Battery positive (+) → Terminal 8 (MF)
      Battery negative (-) → Terminal 7 (MR)
      Retracted position (E)
      Moves from (E) to driving position (C)

      NOTICE:
      1. Disconnect and reconnect the battery between each mirror position check.
      1. Do not apply battery voltage when moving the mirror by hand into each mirror position.

      Text in Illustration 
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly RH)
      If the result is not as specified, replace the outer rear view mirror assembly RH.



    B166836E04
  1. w/ EC Mirror:
    Check the EC mirror operation.

    NOTICE:
    Do not apply a voltage of 1.5 V or higher.


    1. Connect a 1.5 V dry-cell battery.

    2. Apply 1.5 V dry-cell battery voltage and check operation of the mirror face as shown in the table and illustration.

      OK:
      Tester Connection
      Specified Condition
      1.5 V dry-cell battery positive (+) → Terminal 14 (EC+)
      1.5 V dry-cell battery negative (-) → Terminal 13 (EC-)
      Mirror surface becomes dark

      Text in Illustration 
      *a
      Bright
      *b
      Dark
      *c
      Component without harness connected
      (Outer Rear View Mirror Assembly RH)
      If the result is not as specified, replace the outer rear view mirror assembly RH.



    B166382E03
  1. w/ Outer Mirror Light:
    Check the door mirror foot light.

    1. Apply battery voltage to the terminals of the connector, and check the illumination condition.

      OK:
      Tester Connection
      Specified Condition
      Battery positive (+) → Terminal 6 (MLP)
      Battery negative (-) → Terminal 5 (MLP-)
      Door mirror foot light illuminates

      Text in Illustration 
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly RH)
      If the result is not as specified, replace the outer mirror light assembly RH.



    B166378E07
  1. w/ Mirror Heater:
    Check the mirror heater.

    1. Apply battery voltage and check the operation of the mirror heater.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 1 (+)
      Battery negative (-) → Terminal 2 (-)
      Mirror becomes warm

      Text in Illustration 
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly RH)

      HINT:
      It will take a short time for the mirror to become warm.

      If the result is not as specified, replace the outer rear view mirror assembly RH.



4. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (for Extended Type)


    B166367E02
  1. Check the outer mirror motor operation.

    1. Apply battery voltage and check operation of the mirror face.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 10 (MV)
      Battery negative (-) → Terminal 11 (M+)
      Turns upward (A)
      Battery positive (+) → Terminal 11 (M+)
      Battery negative (-) → Terminal 10 (MV)
      Turns downward (B)
      Battery positive (+) → Terminal 12 (MH)
      Battery negative (-) → Terminal 11 (M+)
      Turns left (C)
      Battery positive (+) → Terminal 11 (M+)
      Battery negative (-) → Terminal 12 (MH)
      Turns right (D)

      Text in Illustration 
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly RH)
      If the result is not as specified, replace the outer rear view mirror assembly RH.



    B166832E03
  1. Check the door mirror turn indicator.

    1. Apply battery voltage to the terminals of the connector, and check the LED illumination condition.

      OK:
      Tester Connection
      Specified Condition
      Battery positive (+) → Terminal 4 (TRNR)
      Battery negative (-) → Terminal 3 (GND)
      Door mirror turn indicator illuminates

      Text in Illustration 
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly RH)
      If the result is not as specified, replace the outer rear view mirror assembly RH.



    B166834E03
  1. w/ Running light:
    Check the running light.

    1. Apply battery voltage to the terminals of the connector, and check the LED illumination condition.

      OK:
      Tester Connection
      Specified Condition
      Battery positive (+) → Terminal 9 (RR)
      Battery negative (-) → Terminal 3 (GND)
      Running light illuminates

      Text in Illustration 
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly RH)
      If the result is not as specified, replace the outer rear view mirror assembly RH.



  1. Check the mirror heater.



      B166368E03
    1. Apply battery voltage and check the operation of the mirror heater.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 1 (+)
      Battery negative (-) → Terminal 2 (-)
      Mirror becomes warm

      Text in Illustration 
      *a
      Component without harness connected
      (Outer Rear View Mirror Assembly RH)

      HINT:
      It will take a short time for the mirror to become warm.

      If the result is not as specified, replace the outer rear view mirror assembly RH.