Home › TRANSMISSION ยท AB60F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM

DTC    P0711    Transmission Fluid Temperature Sensor "A" Performance

for Preparation Click here


DESCRIPTION

Refer to DTC P0712 .

DTC Code
DTC Detection Condition
Trouble Area
P0711
One of the following conditions (A)*, (B) or (C) is met:
(A) (a), (b) and (c) are detected: (2-trip detection logic)*
  1. (a) Intake air and engine coolant temperatures are 15°C (59°F) or higher at engine start
  2. (b) Soak time is 5 hours or more
  3. (c) After normal driving for over 5 minutes and 4.9 km (3.0 miles) or more, ATF temperature is below 20°C (68°F)
(B) Both (a) and (b) are detected: (2-trip detection logic)
  1. (a) Intake air and engine coolant temperatures are -10°C (14°F) or higher at engine start
  2. (b) After normal driving for over 21 minutes and 40 seconds and 9 km (5.6 miles) or more, ATF temperature is below 20°C (68°F)
(C) Both (a) and (b) are detected: (2-trip detection logic)
  1. (a) Engine coolant temperature is below 35°C (95°F) at engine start
  2. (b) ATF temperature is 105°C (221°F) or higher when engine coolant temperature reaches 60°C (140°F)
No. 1 transmission wire (No. 1 ATF temperature sensor)
  1. *: Except Mexico models

MONITOR DESCRIPTION

This DTC indicates that there is a problem with output from the Automatic Transmission Fluid (ATF) temperature sensor and that the sensor itself is defective. The ATF temperature sensor converts the ATF temperature to an electrical resistance value. Based on the resistance, the ECM determines the ATF temperature and detects an open or short in the ATF temperature sensor circuit or a fault in the ATF temperature sensor.
After running the vehicle for a certain period, the ATF temperature should increase. If the ATF temperature is below 20°C (68°F) after running the vehicle for a certain period, the ECM interprets this as a fault, turns on the MIL and stores the DTC.
When the ATF temperature is 105°C (221°F) or more and engine coolant temperature reaches 60°C (140°F) after cold start, the ECM also determines this as a fault, turns on the MIL and stores the DTC.

MONITOR STRATEGY


Related DTCs
P0711: ATF temperature sensor/Rationality check
Required sensors/Components
ATF temperature sensor
Frequency of operation
Continuous
Duration
Condition (A), (B), (C) and (D): 3 seconds
Condition (E): Continuous
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


All 
The monitor will run whenever the following DTCs are not present
P0712, P0713, P2740, P2742, P2743 (ATF temperature sensor "A" circuit)
P0115, P0116, P0117, P0118, P011B (ECT (Engine Coolant Temperature) sensor circuit)
P0110, P0111, P0112, P0113 (IAT (Intake air temperature) sensor circuit)
U0100 (CAN communication system)
P2610 (Soak timer circuit)

Condition (A) (Except Mexico models) 
Duration time from engine start
12 seconds or more
ECT
-15°C (5°F) or higher
Permission flag for ATF temperature rationality check
ON
Time after engine start except for continuing shift position "N" or "P"*2
5 minutes or more
Accumulated driving time*1
90 seconds or more
Driving distance after engine start*3
4.9 km (3.0 miles) or more
ECT (12 seconds after engine start)
15°C (59°F) or higher
IAT*4
15°C (59°F) or higher
Soak time
5 hours or more

Condition (B) 
Duration time from engine start
12 seconds or more
ECT
-15°C (5°F) or higher
Permission flag for ATF temperature rationality check
ON
Time after engine start except for continuing shift position "N" or "P"*2
21 minutes and 40 seconds or more
Accumulated driving time*1
250 seconds or more
Driving distance after engine start*3
9.0 km (5.6 miles) or more
ECT (12 seconds after engine start)
-10°C (14°F) or higher
IAT*4
-10°C (14°F) or higher

Condition (C) 
Duration time from engine start
12 seconds or more
ECT
-15°C (5°F) or higher
Permission flag for ATF temperature rationality check
ON
Time after engine start except for continuing shift position "N" or "P"*2
30 minutes or more
Accumulated driving time*1
400 seconds or more
Driving distance after engine start*3
16.0 km (9.9 miles) or more
ECT (12 seconds after engine start)
-15°C (5°F) or higher
IAT*4
-15°C (5°F) or higher

Condition (D) 
Duration time from engine start
12 seconds or more
ECT
-15°C (5°F) or higher
Permission flag for ATF temperature rationality check
ON
Time after engine start except for continuing shift position "N" or "P"*2
55 minutes or more
Accumulated driving time*1
750 seconds or more
Driving distance after engine start*3
27.0 km (16.8 miles) or more

Condition (E) 
Duration time for ECT to reach 60°C (140°F)
10 seconds or more
ATF temperature (12 seconds after engine start)
105°C (221°F) or higher
ECT (12 seconds after engine start)
Below 35°C (95°F)

HINT:

  1. *1: Following conditions are met 
    Engine speed - Turbine speed
    50 rpm or more
    Output speed
    400 rpm or more
    Throttle valve opening angle
    5.5% or more
    Shift position
    Not "N" or "P"
    Engine
    Starting
    However, accumulated driving time is cleared
    -
    When following condition met
    -
    Duration time from shift position "N" or "P"
    300 seconds or more

  2. *2: Time after engine start is cleared when following condition met 
    Duration time from shift position "N" or "P"
    300 seconds or more

  3. *3: Driving distance is cleared when following condition met 
    Duration time from shift position "N" or "P"
    300 seconds or more

  4. *4: IAT is measured when either of following conditions met 
    12 sec. after engine start
    -
    Duration time from shift position "N" or "P"
    300 seconds or more


TYPICAL MALFUNCTION THRESHOLDS

When either condition below is met: Condition (A)*, (B), (C), (D) or (E)

Condition (A)*, (B), (C) and (D) 
ATF temperature
Below 20°C (68°F)
  1. *: Except Mexico models

Condition (E) 
ATF temperature
105°C (221°F) or higher

COMPONENT OPERATING RANGE


Condition (A)*, (B), (C) and (D) 
ATF temperature
20°C (68°F) or higher
  1. *: Except Mexico models

Condition (E) 
ATF temperature
Below 105°C (221°F)

WIRING DIAGRAM

Refer to DTC P0712 .

INSPECTION PROCEDURE

NOTICE:
  1. Perform the universal trip to clear permanent DTCs (Click here).
  2. If DTCs P0711 and P2610 are output simultaneously, confirm that the ATF temperature is as specified in "Normal Condition" using the Techstream first. When the ATF temperature is as specified in "Normal Condition", perform troubleshooting for DTC P2610 (Click herefor 3UR-FE, Click here for 3UR-FBE).


DATA LIST

HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the Techstream to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the Techstream on.

  6. Enter the following menus: Powertrain / Engine and ECT / Data List.

  7. According to the display on the Techstream, read the Data List.

    Engine and ECT: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    A/T Oil Temperature 1
    No. 1 ATF temperature sensor value/
    Min.: -40°C (-40°F)
    Max.: 215°C (419°F)
    1. After stall test: Approximately 80°C (176°F)
    2. With engine cold: Equal to ambient temperature
    If value is -40°C (-40°F) or 215°C (419°F), No. 1 ATF temperature sensor circuit is open or shorted

    HINT:
    When DTC P0712 is output and the Techstream output is 150°C (302°F) or more, there is a short circuit.
    When DTC P0713 is output and the Techstream output is -40°C (-40°F), there is an open circuit.
    Check the temperature displayed on the Techstream in order to check if a malfunction exists.


    Temperature Displayed
    Malfunction
    -40°C (-40°F)
    Open circuit
    150°C (302°F) or more
    Short circuit
    If a circuit related to the ATF temperature sensor becomes open, P0713 is immediately set (in 0.5 seconds). When P0713 is set, P0711 cannot be detected. It is not necessary to inspect the circuit when P0711 is set.

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P0711)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs using the Techstream.
    Result 
    Result
    Proceed to
    Only P0711 is output
    A
    P0711 and other DTCs are output
    B

    HINT:
    If any other codes besides P0711 are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.CHECK TRANSMISSION FLUID LEVEL
  1. Check the transmission fluid level (Click here).

    OK:
    Automatic transmission fluid level is correct.



NG
ADD FLUID (Click here)
OK

REPAIR OR REPLACE NO. 1 TRANSMISSION WIRE (Click here)