DTC P2757 Torque Converter Clutch Pressure Control Solenoid Performance (Shift Solenoid Valve SLU) |

| DTC Code | DTC Detection Condition | Trouble Area |
| P2757 | Lock-up does not occur when driving in the lock-up range (normal driving at 80 km/h (50 mph)), or lock-up remains ON in the lock-up OFF range (2 trip detection logic) |
|
| Related DTCs | P2757: Shift solenoid valve SLU/Functional check |
| Required sensors/Components | Shift solenoid valve SLU |
| Frequency of operation | Continuous |
| Duration | OFF malfunction (A) 2 seconds OFF malfunction (B) 0.4 seconds ON malfunction 1.8 seconds |
| MIL operation | 2 driving cycles |
| Sequence of operation | None |
| The monitor will run whenever the following DTCs are not present | P0717 (Turbine speed sensor circuit) P0722 (Output speed sensor circuit) P0973, P0974 (Shift solenoid valve S1 circuit) P0976, P0977 (Shift solenoid valve S2 circuit) P0761, P0979, P0980 (Shift solenoid valve S3) P0766, P0982, P0983 (Shift solenoid valve S4) P0985, P0986 (Shift solenoid valve SR circuit) P2759 (Shift solenoid valve SLU circuit) P0327, P0328, P032C, P032D (KCS sensor circuit) P0778 (Shift solenoid valve SL2) P0781 (1 - 2 shift valve) P0729 (Sequence valve) |
| ETCS (Electric Throttle Control System) | Not system down |
| Transmission position | "D" |
| Duration time from shifting "N" to "D" | 4 seconds or more |
| ECT (Engine coolant temperature) | 40°C (104°F) or more |
| Spark advance from max. retard timing by KCS control | 0° crankshaft angle or more |
| Engine | Starting |
| ECM selected gear | 2nd, 3rd, 4th, 5th or 6th |
| Vehicle speed | 25 km/h (15.5 mph) or more |
| ECM lock-up command | ON (SLU pressure: 513 kPa (5.2 kgf/cm2, 74 psi) or more) |
| Duration time from lock-up on command | 3 seconds or more |
| Vehicle speed | Less than 120 km/h (74.6 mph) |
| ECM selected gear | 2nd |
| Vehicle speed | 2 km/h (1.2 mph) or more |
| Output speed | 2nd → 1st down-shift point or more |
| Throttle valve opening angle | 9% or more at 2000 rpm (Conditions vary with engine speed) |
| ECM lock-up command | OFF (SLU pressure: Less than 4 kPa (0.04 kgf/cm2, 0.6 psi)) |
| Duration time from lock-up off command | 3 seconds or more |
| Throttle valve opening angle | 6% or more |
| Vehicle speed | Less than 120 km/h (74.6 mph) at 2nd gear (Varies with ECM selected gear) |
| Engine speed - Turbine speed (NE - NT) | 70 rpm or more |
| Turbine speed/Output speed (NT/NO) | Less than 3.11 or more than 7.58 |
| Engine speed - Turbine speed (NE - NT) | Less than 35 rpm |
| Speed sensor (NT) | Input speed is equal to engine speed when lock-up ON. |
| ACTIVE TEST |
Warm up the engine.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the Techstream, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Activate the Lock Up | Control shift solenoid SLU to set automatic transmission to lock-up condition | ON or OFF | Possible to check shift solenoid valve SLU operation [Vehicle Condition]
|
Lightly depress the accelerator pedal and check that the engine speed does not change abruptly.

| 1.CHECK DTC OUTPUT (IN ADDITION TO DTC P2757) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs using the Techstream.
| Result | Proceed to |
| Only P2757 is output | A |
| P2757 and other DTCs are output | B |
|
| ||||
| A | |
| 2.INSPECT SHIFT SOLENOID VALVE SLU |
![]() |
Remove shift solenoid valve SLU.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
Connect the battery's positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector. Then check that the valve moves and makes an operating noise.
|
| ||||
| OK | |
| 3.INSPECT TRANSMISSION VALVE BODY ASSEMBLY |
Check the transmission valve body assembly (Click here).
|
| ||||
| OK | |
| 4.INSPECT TORQUE CONVERTER ASSEMBLY |
Check the torque converter assembly (Click here).
|
| ||||
| OK | ||
| ||