Home › TRANSMISSION · A750E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM

DTC    P0751    Shift Solenoid "A" Performance (Shift Solenoid Valve S1)

for Preparation Click here


DESCRIPTION

The ECM uses signals from the output shaft speed sensor and input speed sensor to detect the actual gear position (1st, 2nd, 3rd, 4th or 5th gear).
Then the ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical problems of the shift solenoid valves, valve body or automatic transmission (clutch, brake, gear, etc.).

DTC Code
DTC Detection Condition
Trouble Area
P0751
Gear required by the ECM does not match the actual gear when driving. (2 trip detection logic)
  1. Shift solenoid valve S1 remains open or closed
  2. Shift solenoid valve SLT remains open or closed
  3. Valve body is blocked
  4. Automatic transmission (clutch, brake, gear, etc.)

MONITOR DESCRIPTION

This DTC indicates a stuck ON malfunction or stuck OFF malfunction of the shift solenoid valve S1.
The ECM commands gear shifts by turning the shift solenoid valves ON/OFF. When the gear position commanded by the ECM and the actual gear position are not the same, the ECM illuminates the MIL and stores the DTC.

MONITOR STRATEGY


Related DTCs
P0751: Shift solenoid valve S1/Functional check
Required sensors/Components
Shift solenoid valve S1, Vehicle sensor, Throttle position sensor, Speed sensor (NT), Speed sensor (NO)
Frequency of operation
Continuous
Duration
OFF malfunction (A) and (B):
0.4 sec.
OFF malfunction (C):
Immediately
ON malfunction (A), (B) and (C):
0.4 sec.
ON malfunction (D):
3 sec.
ON malfunction (E):
0.5 sec.
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


All 
The monitor will run whenever the following DTCs are not present
P0717 (Turbine speed sensor circuit)
P0722 (Output speed sensor circuit)
P0973, P0974 (Shift solenoid valve S1 circuit)
P0976, P0977 (Shift solenoid valve S2 circuit)
P0985, P0986 (Shift solenoid valve SR circuit)
P0748 (Shift solenoid valve SL1 circuit)
P0778 (Shift solenoid valve SL2 circuit)
P0128 (ECT (Engine Coolant Temperature) sensor circuit)
P0327, P0328, P0332, P0333 (KCS sensor circuit)
ETCS (Electric Throttle Control System)
Not system down
Transmission position
"D"
Duration time from shifting "N" to "D"
4 sec. or more
ECT
40°C (104°F) or more
Spark advance from max. retard timing by KCS control
0° crankshaft angle or more
Engine
Starting

OFF malfunction (A) 
ECM selected gear
1st
Vehicle speed
2 km/h (1.2 mph) or more, and less than 40 km/h (24.9 mph)
Throttle valve opening angle
8% or more (When actual gear is 4th)
6.5% or more at 2000 rpm (Conditions vary with engine speed)

OFF malfunction (B) 
Current ECM selected gear
5th
Last ECM selected gear
4th
Continuous time for ECM selecting 4th gear
2 sec. or more
Actual gear when ECM selected 4th gear
4th

OFF malfunction (C) 
Current ECM selected gear
5th
Last ECM selected gear
4th

ON malfunction (A) 
ECM selected gear
1st
Vehicle speed
2 km/h (1.2 mph) or more, and less than 40 km/h (24.9 mph)
Throttle valve opening angle
8% or more (When actual gear is 4th)
6.5% or more at 2000 rpm (Conditions vary with engine speed)

ON malfunction (B) 
ECM selected gear
4th
Vehicle speed
2 km/h (1.2 mph) or more
Throttle valve opening angle
6.5% or more at 2000 rpm
(Conditions vary with engine speed)

ON malfunction (C) 
ECM selected gear
3rd
Vehicle speed
2 km/h (1.2 mph) or more
Throttle valve opening angle
6.5% or more at 2000 rpm
(Conditions vary with engine speed)

ON malfunction (D) 
Current ECM selected gear
5th
Last ECM selected gear
4th
Vehicle speed
(During transition from 4th to 5th gear)
Less than 100 km/h (62.2 mph)

ON malfunction (E) 
ECM selected gear
5th
Engine speed - Turbine speed (NE - NT)
(After transition from 4th to 5th gear)
150 rpm or less
Vehicle speed
(After transition from 4th to 5th gear)
Less than 100 km/h (62.2 mph)

TYPICAL MALFUNCTION THRESHOLDS

[OFF malfunction]
  1. All of the following conditions are met: OFF malfunction (A), (B) and (C)
    2 detections are necessary per driving cycle:
    1st detection: Temporary flag ON
    2nd detection: Pending fault code ON

OFF malfunction (A) 
Turbine speed/Output speed (NT/NO)
0.93 or more, and 1.07 or less
(This means actual gear is 4th)

OFF malfunction (B) 
Turbine speed/Output speed (NT/NO)
0.65 or more, and 0.79 or less
(This means actual gear is 5th)

OFF malfunction (C) 
Output record of ECM from 4th to 5th up-shift
Recorded
[ON malfunction]
  1. Either of the following conditions is met:
    ON malfunction (A) and (B)
    ON malfunction (B) or (C), and ON malfunction (D) or (E)

ON malfunction (A) and (B) 
Turbine speed/Output speed (NT/NO)
3.30 or more, and 7.50 or less
(This means actual gear is 1st)

ON malfunction (C) 
Turbine speed/Output speed (NT/NO)
1.91 or more, and 2.35 or less
(This means actual gear is 2nd)

ON malfunction (D) 
Turbine speed - Output speed x 4th gear ratio
(NT - NO x 4th gear ratio)
1000 rpm or more

ON malfunction (E) 
Turbine speed - Output speed x 5th gear ratio
(NT - NO x 5th gear ratio)
1000 rpm or more

INSPECTION PROCEDURE

NOTICE:
Perform the universal trip to clear permanent DTCs (Click here).


ACTIVE TEST

HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the Techstream to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the Techstream on.

  6. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  7. According to the display on the Techstream, perform the Active Test.

    HINT:
    While driving, the shift position can be forcibly changed with the Techstream.
    Comparing the shift position commanded by the Active Test with the actual shift position enables you to confirm the problem (Click here).


    Engine and ECT: 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Control the Shift Position
    Operate shift solenoid valve and set each shift position
    1. Press "→" button: Shift up
    2. Press "←" button: Shift down
    Possible to check operation of shift solenoid valves
    [Vehicle Condition]
    50 km/h (31 mph) or less

    HINT:
    1. This test can be conducted when the vehicle speed is 50 km/h (31 mph) or less.
    2. The 4th to 5th up-shift must be performed with the accelerator pedal released.
    3. The 5th to 4th down-shift must be performed with the accelerator pedal released.
    4. Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.
    5. The shift position commanded by the ECM is shown in the Data List display on the Techstream.
    6. The shift solenoid valve S1 turns ON/OFF normally when the shift lever is in the D position.

      ECM gear shift command
      1st
      2nd
      3rd
      4th
      5th
      Shift solenoid valve S1
      ON
      ON
      OFF
      OFF
      OFF

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P0751)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs using the Techstream.
    Result 
    Result
    Proceed to
    Only P0751 is output
    A
    P0751 and other DTCs are output
    B

    HINT:
    If any other codes besides P0751 are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING TECHSTREAM (SHIFT SOLENOID VALVE SLT)

NOTICE:
  1. Perform the test at the normal operating ATF temperature: 50 to 80°C (122 to 176°F).
  2. Be careful to prevent SST's hose from interfering with the exhaust pipe.
  3. Perform the test with the A/C OFF.

HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.



    C159068E01
  1. Remove the test plug on the transmission case center right side and connect SST.

SST
09992-00095   (09992-00231, 09992-00271)
  1. Connect the Techstream to the DLC3.

  1. Start the engine and warm it up.

  1. Measure the line pressure with SST.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  1. According to the display on the Techstream, perform the Active Test.

  1. Measure the line pressure.

    Engine and ECT: 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Activate the Solenoid (SLT)*
    Operate shift solenoid SLT and raise line pressure
    ON or OFF

    HINT:
    1. OFF: Line pressure up (when Active Test "Activate the Solenoid (SLT)" is performed, ECM commands SLT solenoid to turn OFF)
    2. ON: No action (normal operation)

    [Vehicle Condition]
    1. Vehicle stopped
    2. Engine idling

    HINT:
    *: Activate the Solenoid (SLT) in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transmission, which is used in the Hydraulic Test (Click here) as well. Note that the pressure values in the Active Test and Hydraulic Test are different.

OK:
The line pressure changes as specified when performing the Active Test.



NG
REPLACE SHIFT SOLENOID VALVE SLT
OK


3.INSPECT SHIFT SOLENOID VALVE S1


    C159062E01
  1. Remove shift solenoid valve S1.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Shift solenoid S1 connector - Shift solenoid S1 body
    20°C (68°F)
    11 to 15 Ω

  1. Connect the battery's positive (+) lead to the terminal of the solenoid valve connector, and the negative (-) lead to the solenoid body. Then check that the valve moves and makes an operating noise.

    OK:
    Valve moves and makes an operating noise.



NG
REPLACE SHIFT SOLENOID VALVE S1
OK


4.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
  1. Check the transmission valve body assembly (Click here).

    OK:
    There are no foreign objects on any valve.



NG
REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY (Click here)
OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY (Click here)