Home › TRANSMISSION · A760F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM

AUTOMATIC TRANSMISSION SYSTEM > Transmission Control Switch Circuit

for Preparation Click here


DESCRIPTION

After moving the shift lever to S, it is possible to switch the shift range between "1" (S1 range) and "6" (S6 range) using the transmission control switch.
Shifting to "+" once raises the shift range by one, and shifting to "-" once lowers the shift range by one.

WIRING DIAGRAM


C160114E01


INSPECTION PROCEDURE

1.INSPECT TRANSMISSION CONTROL SWITCH


    C210665E05
  1. for Column Shift Type:

    1. Disconnect the J25 transmission control switch connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      6 (IG) - 13 (S)
      Shift lever in S, "+" or "-"
      Below 1 Ω
      5 (SFTU) - 11 (E)
      Shift lever held in "+"
      (Up-shift)
      Below 1 Ω
      4 (SFTD) - 11 (E)
      Shift lever held in "-"
      (Down-shift)
      Below 1 Ω
      6 (IG) - 13 (S)
      Shift lever not in S, "+" or "-"
      10 kΩ or higher
      5 (SFTU) - 11 (E)
      Shift lever in S
      10 kΩ or higher
      4 (SFTD) - 11 (E)
      Shift lever in S
      10 kΩ or higher

      Text in Illustration 
      *a
      Component without harness connected
      (Transmission Control Switch)



    C203344E13
  1. for Floor Shift Type:

    1. Disconnect the J24 transmission control switch connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      3 (IG) - 7 (S)
      Shift lever in S, "+" or "-"
      Below 1 Ω
      2 (SFTU) - 5 (E)
      Shift lever held in "+"
      (Up-shift)
      Below 1 Ω
      1 (SFTD) - 5 (E)
      Shift lever held in "-"
      (Down-shift)
      Below 1 Ω
      3 (IG) - 7 (S)
      Shift lever not in S, "+" or "-"
      10 kΩ or higher
      2 (SFTU) - 5 (E)
      Shift lever in S
      10 kΩ or higher
      1 (SFTD) - 5 (E)
      Shift lever in S
      10 kΩ or higher

      Text in Illustration 
      *a
      Component without harness connected
      (Transmission Control Switch)
      Result 
      Result
      Proceed to
      OK
      A
      NG (for Column Shift Type)
      B
      NG (for Floor Shift Type)
      C



B
REPLACE TRANSMISSION CONTROL SWITCH (COLUMN SHIFT SHIFT LEVER SUB-ASSEMBLY) (Click here)

C
REPLACE TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY) (Click here)
A


2.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BATTERY, BODY GROUND)


    C210666E06
  1. for Column Shift Type:

    1. Disconnect the J25 transmission control switch connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      J25-6 (IG) - Body ground
      Ignition switch ON
      11 to 14 V
      J25-6 (IG) - Body ground
      Ignition switch off
      Below 1 V

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      J25-11 (E) - Body ground
      Always
      Below 1 Ω

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to Transmission Control Switch)



    C203343E14
  1. for Floor Shift Type:

    1. Disconnect the J24 transmission control switch connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      J24-3 (IG) - Body ground
      Ignition switch ON
      11 to 14 V
      J24-3 (IG) - Body ground
      Ignition switch off
      Below 1 V

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      J24-5 (E) - Body ground
      Always
      Below 1 Ω

      Text in Illustration 
      *a
      Front view of wire harness connector
      (to Transmission Control Switch)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)


    C197708E30
  1. Disconnect the A24 ECM connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A24-25 (S) - Body ground
    1. Ignition switch ON
    2. Shift lever in S, "+" or "-"
    11 to 14 V
    A24-25 (S) - Body ground
    1. Ignition switch ON
    2. Shift lever not in S, "+" or "-"
    Below 1 V

  1. Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A24-38 (SFTU) - Body ground
    Shift lever held in "+"
    (Up-shift)
    Below 1 Ω
    A24-27 (SFTD) - Body ground
    Shift lever held in "-"
    (Down-shift)
    Below 1 Ω
    A24-38 (SFTU) - Body ground
    Shift lever in S
    10 kΩ or higher
    A24-27 (SFTD) - Body ground
    Shift lever in S
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)