AUTOMATIC TRANSMISSION SYSTEM > Transmission Control Switch Circuit |

| 1.INSPECT TRANSMISSION CONTROL SWITCH |
![]() |
for Column Shift Type:
Disconnect the J25 transmission control switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 6 (IG) - 13 (S) | Shift lever position on S, "+" or "-" | Below 1 Ω |
| 5 (SFTU) - 11 (E) | Shift lever held in "+" (Up-shift) | Below 1 Ω |
| 4 (SFTD) - 11 (E) | Shift lever held in "-" (Down-shift) | Below 1 Ω |
| 6 (IG) - 13 (S) | Shift lever position not on S, "+" or "-" | 10 kΩ or higher |
| 5 (SFTU) - 11 (E) | Shift lever position on S | 10 kΩ or higher |
| 4 (SFTD) - 11 (E) | Shift lever position on S | 10 kΩ or higher |
![]() |
for Floor Shift Type:
Disconnect the J24 transmission control switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 (IG) - 7 (S) | Shift lever position on S, "+" or "-" | Below 1 Ω |
| 2 (SFTU) - 5 (E) | Shift lever held in "+" (Up-shift) | Below 1 Ω |
| 1 (SFTD) - 5 (E) | Shift lever held in "-" (Down-shift) | Below 1 Ω |
| 3 (IG) - 7 (S) | Shift lever position not on S, "+" or "-" | 10 kΩ or higher |
| 2 (SFTU) - 5 (E) | Shift lever position on S | 10 kΩ or higher |
| 1 (SFTD) - 5 (E) | Shift lever position on S | 10 kΩ or higher |
| Result | Proceed to |
| OK | A |
| NG (for Column Shift Type) | B |
| NG (for Floor Shift Type) | C |
|
| ||||
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BATTERY, BODY GROUND) |
![]() |
for Column Shift Type:
Disconnect the J25 transmission control switch connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J25-6 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| J25-6 (IG) - Body ground | Ignition switch off | Below 1 V |
Turn the ignition switch off.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J25-11 (E) - Body ground | Always | Below 1 Ω |
![]() |
for Floor Shift Type:
Disconnect the J24 transmission control switch connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J24-3 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| J24-3 (IG) - Body ground | Ignition switch off | Below 1 V |
Turn the ignition switch off.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J24-5 (E) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM) |
![]() |
Disconnect the A24 ECM connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A24-25 (S) - Body ground |
| 11 to 14 V |
| A24-25 (S) - Body ground |
| Below 1 V |
Turn the ignition switch off.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A24-38 (SFTU) - Body ground | Shift lever held in "+" (Up-shift) | Below 1 Ω |
| A24-27 (SFTD) - Body ground | Shift lever held in "-" (Down-shift) | Below 1 Ω |
| A24-38 (SFTU) - Body ground | Shift lever position on S | 10 kΩ or higher |
| A24-27 (SFTD) - Body ground | Shift lever position on S | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||