CYLINDER HEAD > INSPECTION |
| 1. CLEAN CYLINDER HEAD SUB-ASSEMBLY |
Using a gasket scraper, remove all the gasket material from the surface which contacts the cylinder block.
Using a wire brush, remove all the carbon from the combustion chambers.
![]() |
Using a valve guide bushing brush and solvent, clean all the guide bushes.
Using a soft brush and solvent, thoroughly clean the cylinder head.
| 2. INSPECT CYLINDER HEAD SUB-ASSEMBLY |
![]() |
Using a precision straightedge and feeler gauge, measure the warpage of the surfaces which contact the cylinder block sub-assembly and manifolds.
| Item | Specified Condition |
| Cylinder block side | 0.05 mm (0.00197 in.) |
| Intake side | 0.08 mm (0.00315 in.) |
| Exhaust side | 0.08 mm (0.00315 in.) |
| Item | Specified Condition |
| Cylinder block side | 0.10 mm (0.00394 in.) |
| Intake side | 0.10 mm (0.00394 in.) |
| Exhaust side | 0.10 mm (0.00394 in.) |
| *A | Cylinder Block Side |
| *B | Intake Side |
| *C | Exhaust Side |
Using a dye penetrant, check the intake ports, exhaust ports and cylinder surface for cracks.
If cracked, replace the cylinder head sub-assembly.
| 3. CLEAN VALVE SEAT |
![]() |
Using a 45° carbon cutter, resurface the valve seats.
| *1 | 45° Carbon Cutter |
| 4. INSPECT INTAKE VALVE |
Clean the valves.
Using a gasket scraper, chip off any carbon from the valve head.
Using a wire brush, thoroughly clean the valve.
Using a micrometer, measure the diameter of the valve stem.
![]() |
Check the valve face angle.
| *1 | Valve Face Angle |
Grind the valve sufficiently to remove pits and carbon.
Check that the valve is ground to the correct valve face angle.
![]() |
Using a vernier caliper, measure the valve head margin thickness.
| *1 | Margin Thickness |
Using a vernier caliper, measure the valve overall length.
| 5. INSPECT EXHAUST VALVE |
Clean the valves.
Using a gasket scraper, chip off any carbon from the valve head.
Using a wire brush, thoroughly clean the valve.
Using a micrometer, measure the diameter of the valve stem.
![]() |
Check the valve face angle.
| *1 | Valve Face Angle |
Grind the valve sufficiently to remove pits and carbon.
Check that the valve is ground to the correct valve face angle.
![]() |
Using a vernier caliper, measure the valve head margin thickness.
| *1 | Margin Thickness |
Using a vernier caliper, measure the valve overall length.
| 6. INSPECT VALVE GUIDE BUSH OIL CLEARANCE |
![]() |
Using a caliper gauge, measure the inside diameter of the valve guide bush.
Subtract the valve stem diameter measurement from the valve guide bush inside diameter measurement.
| Item | Specified Condition |
| Intake | 0.025 to 0.060 mm (0.000984 to 0.00236 in.) |
| Exhaust | 0.030 to 0.065 mm (0.00118 to 0.00256 in.) |
| Item | Specified Condition |
| Intake | 0.08 mm (0.00315 in.) |
| Exhaust | 0.10 mm (0.00394 in.) |
| 7. INSPECT INTAKE VALVE SEAT |
Apply a light coat of Prussian blue to the valve face.
Lightly press the valve face against the valve seat.
![]() |
Check the valve face and valve seat by using the following procedure:
| *1 | Width |
Check that Prussian blue appears around the entire valve face. If not, replace the valve.
If Prussian blue appears around the entire valve seat, the guide and valve face are concentric. If not, resurface the valve seat.
Check that the valve seat contacts the middle of the valve face with the width between 1.1 and 1.5 mm (0.0433 and 0.0591 in.).
| 8. INSPECT EXHAUST VALVE SEAT |
Apply a light coat of Prussian blue to the valve face.
Lightly press the valve face against the valve seat.
![]() |
Check the valve face and valve seat by using the following procedure:
| *1 | Width |
Check that Prussian blue appears around the entire valve face. If not, replace the valve.
If Prussian blue appears around the entire valve seat, the guide and valve face are concentric. If not, resurface the valve seat.
Check that the valve seat contacts the middle of the valve face with the width between 1.1 and 1.5 mm (0.0433 and 0.0591 in.).
| 9. INSPECT INNER COMPRESSION SPRING |
![]() |
Using a vernier caliper, measure the free length of the inner compression spring.
![]() |
Using a steel square, measure the deviation of the inner compression spring.
| *1 | Deviation |
![]() |
Using a spring tester, measure the tension of the valve spring when it is compressed to the specified installation length.