Home › ENGINE · 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0351    Ignition Coil "A" Primary / Secondary Circuit

DTC    P0352    Ignition Coil "B" Primary / Secondary Circuit

DTC    P0353    Ignition Coil "C" Primary / Secondary Circuit

DTC    P0354    Ignition Coil "D" Primary / Secondary Circuit

DTC    P0355    Ignition Coil "E" Primary / Secondary Circuit

DTC    P0356    Ignition Coil "F" Primary / Secondary Circuit

for Preparation Click here


DESCRIPTION

HINT:
  1. These DTCs indicate malfunctions relating to the primary circuit.
  2. If DTC P0351 is output, check the No. 1 ignition coil assembly circuit.
  3. If DTC P0352 is output, check the No. 2 ignition coil assembly circuit.
  4. If DTC P0353 is output, check the No. 3 ignition coil assembly circuit.
  5. If DTC P0354 is output, check the No. 4 ignition coil assembly circuit.
  6. If DTC P0355 is output, check the No. 5 ignition coil assembly circuit.
  7. If DTC P0356 is output, check the No. 6 ignition coil assembly circuit.

A Direct Ignition System (DIS) is used on this vehicle.
The DIS is a 1-cylinder ignition system in which each cylinder is ignited by one ignition coil and one spark plug is connected to the end of each secondary wiring. A powerful voltage, generated in the secondary wiring, is applied directly to each spark plug. The sparks of the spark plugs pass from the center electrode to the ground electrodes.
The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches the current to the primary coil on and off. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back an ignition confirmation (IGF) signal to the ECM for each cylinder ignition.

A226985E07


DTC No.
DTC Detection Condition
Trouble Area
P0351
P0352
P0353
P0354
P0355
P0356
No IGF signal is sent to the ECM while the engine is running (1 trip detection logic).
  1. Ignition system
  2. Open or short in IGF1 or IGT1 circuit (to 6) between ignition coil assembly and ECM
  3. No. 1 to No. 6 ignition coil assembly
  4. ECM

  1. G035664E01
  2. Reference: Inspection using an oscilloscope.
  3. While cranking or idling the engine, check the waveform between terminals IGT1 (to 6) and E1, and IGF1 and E1 of the ECM connector.
    Item
    Content
    Terminal
    CH1: IGT1, IGT2, IGT3, IGT4, IGT5, IGT6 - E1
    CH2: IGF1 - E1
    Equipment Setting
    2 V/DIV.
    20 msec./DIV.
    Condition
    Cranking or idling

MONITOR DESCRIPTION


A212405E11

If the ECM does not receive any IGF signals despite transmitting the IGT signal, it interprets this as a fault in the igniter and stores a DTC.
If the malfunction is not repaired successfully, a DTC is stored 1 second after the engine is next started.

MONITOR STRATEGY


Related DTCs
P0351: Igniter (cylinder 1) malfunction
P0352: Igniter (cylinder 2) malfunction
P0353: Igniter (cylinder 3) malfunction
P0354: Igniter (cylinder 4) malfunction
P0355: Igniter (cylinder 5) malfunction
P0356: Igniter (cylinder 6) malfunction
Required Sensors/Components (Main)
Ignition coil assembly (Cylinder 1 to 6)
Required Sensors/Components (Related)
Crankshaft position sensor
Frequency of Operation
Continuous
Duration
-
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs not stored
None
All of the following conditions are met
-
Spark cut
Not operating
Either of following conditions A or B met
-
A. Engine speed
1500 rpm or less
B. Starter
OFF
Either of following conditions C or D met
-
C. Both of following conditions (a) and (b) met
-
(a) Engine speed
500 rpm or less
(b) Battery voltage
6 V or higher
D. All of following conditions (a), (b) and (c) met
-
(a) Engine speed
More than 500 rpm
(b) Battery voltage
10 V or higher
(c) Number of sparks after CPU reset
5 sparks or more

TYPICAL MALFUNCTION THRESHOLDS


All of the following conditions are met
-
A. Ignition signal fail counter
More than 2 times
B. Time after condition A is met
0.256 seconds or more
C. Ignition signal fail count after condition B is met
More than 2 times
D. Ignition switch
ON

COMPONENT OPERATING RANGE


IGF signal
Igniter transmits IGF signal when it receives IGT signal from ECM

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on.
  6. Start the engine.
  7. Idle the engine for 10 seconds or more.
  8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
  9. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  11. Input the DTC: P0351, P0352, P0353, P0354, P0355 or P0356.
  12. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows ABNORMAL, the system has a malfunction.
    2. If the judgment result shows INCOMPLETE or N/A, perform steps [B] and [C] again.

  13. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A245731E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.INSPECT IGNITION COIL ASSEMBLY (POWER SOURCE)
A203962E18
  1. Disconnect the ignition coil assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D10-4 (GND) - Body ground
    Always
    Below 1 Ω
    D25-4 (GND) - Body ground
    Always
    Below 1 Ω
    D12-4 (GND) - Body ground
    Always
    Below 1 Ω
    D23-4 (GND) - Body ground
    Always
    Below 1 Ω
    D14-4 (GND) - Body ground
    Always
    Below 1 Ω
    D21-4 (GND) - Body ground
    Always
    Below 1 Ω

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D10-1 (+B) - D10-4 (GND)
    Ignition switch ON
    11 to 14 V
    D25-1 (+B) - D25-4 (GND)
    Ignition switch ON
    11 to 14 V
    D12-1 (+B) - D12-4 (GND)
    Ignition switch ON
    11 to 14 V
    D23-1 (+B) - D23-4 (GND)
    Ignition switch ON
    11 to 14 V
    D14-1 (+B) - D14-4 (GND)
    Ignition switch ON
    11 to 14 V
    D21-1 (+B) - D21-4 (GND)
    Ignition switch ON
    11 to 14 V

Text in Illustration 
*a
Front view of wire harness connector
(to Ignition Coil Assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
  1. Disconnect the ignition coil assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    D10-2 (IGF) - D74-104 (IGF1)
    Always
    Below 1 Ω
    D25-2 (IGF) - D74-104 (IGF1)
    Always
    Below 1 Ω
    D12-2 (IGF) - D74-104 (IGF1)
    Always
    Below 1 Ω
    D23-2 (IGF) - D74-104 (IGF1)
    Always
    Below 1 Ω
    D14-2 (IGF) - D74-104 (IGF1)
    Always
    Below 1 Ω
    D21-2 (IGF) - D74-104 (IGF1)
    Always
    Below 1 Ω
    D10-3 (IGT1) - D74-40 (IGT1)
    Always
    Below 1 Ω
    D25-3 (IGT2) - D74-39 (IGT2)
    Always
    Below 1 Ω
    D12-3 (IGT3) - D74-38 (IGT3)
    Always
    Below 1 Ω
    D23-3 (IGT4) - D74-37 (IGT4)
    Always
    Below 1 Ω
    D14-3 (IGT5) - D74-36 (IGT5)
    Always
    Below 1 Ω
    D21-3 (IGT6) - D74-35 (IGT6)
    Always
    Below 1 Ω
    D10-2 (IGF) or D74-104 (IGF1) - Body ground
    Always
    10 kΩ or higher
    D25-2 (IGF) or D74-104 (IGF1) - Body ground
    Always
    10 kΩ or higher
    D12-2 (IGF) or D74-104 (IGF1) - Body ground
    Always
    10 kΩ or higher
    D23-2 (IGF) or D74-104 (IGF1) - Body ground
    Always
    10 kΩ or higher
    D14-2 (IGF) or D74-104 (IGF1) - Body ground
    Always
    10 kΩ or higher
    D21-2 (IGF) or D74-104 (IGF1) - Body ground
    Always
    10 kΩ or higher
    D10-3 (IGT1) or D74-40 (IGT1) - Body ground
    Always
    10 kΩ or higher
    D25-3 (IGT2) or D74-39 (IGT2) - Body ground
    Always
    10 kΩ or higher
    D12-3 (IGT3) or D74-38 (IGT3) - Body ground
    Always
    10 kΩ or higher
    D23-3 (IGT4) or D74-37 (IGT4) - Body ground
    Always
    10 kΩ or higher
    D14-3 (IGT5) or D74-36 (IGT5) - Body ground
    Always
    10 kΩ or higher
    D21-3 (IGT6) or D74-35 (IGT6) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353, P0354, P0355 OR P0356)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Shuffle the arrangement of the ignition coil assemblies (among the No. 1 to No. 6 cylinders).

    NOTICE:
    Do not shuffle the connectors.

  1. Perform a simulation test.

  1. Check the DTCs output on the Techstream.

    Result 
    Result
    Proceed to
    Same DTC output
    A
    Different ignition coil DTC output
    B

HINT:
Perform "Inspection After Repair" after replacing the ignition coil assembly (Click here).



B
REPLACE IGNITION COIL ASSEMBLY (Click here)
A

REPLACE ECM (Click here)