Home › ENGINE · 3UR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0013    Camshaft Position "B" Actuator Circuit / Open (Bank 1)

DTC    P0023    Camshaft Position "B" Actuator Circuit / Open (Bank 2)

for Preparation Click here


DESCRIPTION

  1. This DTC is designed to detect opens or shorts in the camshaft oil control valve (OCV) circuit. If the OCV duty-cycle is excessively high or low while the engine is running, the ECM will illuminate the MIL and store the DTC.
  2. The VVT (variable valve timing) system adjusts the intake valve timing to improve the driveability. The engine oil pressure turns the camshaft actuator to adjust the valve timing. The OCV is a solenoid valve and switches the engine oil line. The valve moves when the ECM applies 12 volts to the solenoid. The ECM changes the energizing time to the solenoid (duty-cycle) in accordance with the camshaft position, crankshaft position, throttle position, etc.

A192077E02


DTC Code
DTC Detection Condition
Trouble Area
P0013
An open or short in the Camshaft Oil Control Valve (OCV) for exhaust side (for Bank 1) circuit (1 trip detection logic).
  1. Open or short in Camshaft Oil Control Valve (OCV) (for exhaust side of Bank 1) circuit
  2. OCV for exhaust camshaft (for Bank 1)
  3. ECM
P0023
An open or short in the OCV for exhaust side (for Bank 2) circuit (1 trip detection logic).
  1. Open or short in OCV (for exhaust side of Bank 2) circuit
  2. OCV for exhaust camshaft (for Bank 2)
  3. ECM

MONITOR DESCRIPTION

This DTC is designed to detect opens or shorts in the camshaft oil control valve (OCV) circuit. If the OCV's duty-cycle is excessively high or low while the engine is running, the ECM will illuminate the MIL and set the DTC.

MONITOR STRATEGY


Related DTCs
P0013: Exhaust camshaft OCV (for Bank 1)
P0023: Exhaust camshaft OCV (for Bank 2)
Required Sensors/Components (Main)
Exhaust camshaft OCV
Required Sensors/Components (Related)
-
Frequency of operation
Continuous
Duration
1 second
MIL operation
Immediate
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


All 
Monitor runs whenever following DTCs not present
None
All of following conditions met
-
Starter
OFF
Ignition switch
ON
Time after ignition switch off to ON
0.5 seconds or more

Case 1 
One of following conditions met
-
A. All of the following conditions are met
-
Battery voltage
11 to 13 V
Target duty cycle
Less than 70%
B. All of following conditions met
-
Battery voltage
13 V or more
Target duty cycle
Less than 80%

Case 2 
Current cut status
Not cut

TYPICAL MALFUNCTION THRESHOLDS


Case 1 
Output duty cycle
100% or more

Case 2 
Output duty cycle
3% or less

COMPONENT OPERATING RANGE


OCV duty cycle
3 to 100%

CONFIRMATION DRIVING PATTERN


A198818E01

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on.
  6. Wait 5 seconds [A].
  7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].
  8. Read the Pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  9. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  10. Input the DTC: P0013 or P0023.
  11. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit

    HINT:
    If the judgment result shows ABNORMAL, the system has a malfunction.

  12. If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A162759E02


INSPECTION PROCEDURE

HINT:
  1. If DTC P0013 is displayed, check the bank 1 VVT system for exhaust camshaft circuit.
  2. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.
  3. If DTC P0023 is displayed, check the bank 2 VVT system for exhaust camshaft circuit.
  4. Bank 2 refers to the bank that does not include the No. 1 cylinder.
  5. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction (Click here).

1.CHECK DTC (DTC P0013 OR P0023)
  1. Connect the Techstream to the DLC3.

  1. Clear DTC after recording the freeze frame data and DTC.

  1. Turn the ignition switch off.

  1. Allow the engine to idle and check DTC.

  1. Check that P0013 or P0023 is not present.

    OK:
    P0013 or P0023 is not output.



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
  1. Inspect the camshaft oil control valve assembly (Click here).



NG
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (OCV - ECM)
  1. Disconnect the D44 or D45 OCV connector.

  1. Disconnect the D74 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:

    Tester Connection
    Condition
    Specified Condition
    D44-1 - D74-56 (OE1+)
    Always
    Below 1 Ω
    D44-2 - D74-55 (OE1-)
    Always
    Below 1 Ω
    D45-1 - D74-50 (OE2+)
    Always
    Below 1 Ω
    D45-2 - D74-49 (OE2-)
    Always
    Below 1 Ω
    D44-1 or D74-56 (OE1+) - Body ground
    Always
    10 kΩ or higher
    D44-2 or D74-55 (OE1-) - Body ground
    Always
    10 kΩ or higher
    D45-1 or D74-50 (OE2+) - Body ground
    Always
    10 kΩ or higher
    D45-2 or D74-49 (OE2-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)