Home › SUSPENSION & AXLE › TIRE AND WHEEL › TIRE PRESSURE WARNING SYSTEM

TIRE PRESSURE WARNING SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



READ DATA LIST

HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Turn the ignition switch OFF.

  2. Connect the Techstream to the DLC3.

  3. Turn the ignition switch to ON and the Techstream on.

  4. Enter the following menu items: Chassis / Tire Pressure Monitor / Data List.

  5. Check the values by referring to the table below.

    Tire Pressure Monitor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Mode Status
    Tire pressure warning system
    mode/Normal or Test
    Normal: Normal mode
    Test: Test mode
    -
    Main Tire
    Number of tire IDs to be registered/
    4 or 5
    4 should be displayed
    -
    Vehicle Speed
    Vehicle speed reading/
    min.: 0 km/h (0 mph),
    max.: 255 km/h (158 mph)
    Actual vehicle speed
    Speed indicated on the combination meter
    Registered ID1 Code
    Registered ID1 code/
    min.: 0
    max.: FFFFFFFF*1
    The transmitter ID registered in the transmitter ID1 is displayed
    -
    Registered ID2 Code
    Registered ID2 code/
    min.: 0
    max.: FFFFFFFF*1
    The transmitter ID registered in the transmitter ID2 is displayed
    -
    Registered ID3 Code
    Registered ID3 code/
    min.: 0
    max.: FFFFFFFF*1
    The transmitter ID registered in the transmitter ID3 is displayed
    -
    Registered ID4 Code
    Registered ID4 code/
    min.: 0
    max.: FFFFFFFF*1
    The transmitter ID registered in the transmitter ID4 is displayed
    -
    ID Transmission Status
    Transmitter ID transmission status /
    Finish or Now
    Finish or Now
    -
    Initialization Switch
    Tire pressure warning reset switch/
    ON or OFF
    ON: Switch is pressed and held
    OFF: Switch is not pressed
    -
    Initialization SW Info
    Tire pressure warning reset switch setting information/
    WITH or WITHOUT
    WITH or WITHOUT
    -
    ID 1 Tire Inflation Pressure
    ID1 tire inflation pressure /
    min.: Absolute pressure / 100.00 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure / 449.35 kPa (4.5 kgf/cm2, 63 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi)
    Actual tire inflation pressure
    If 100 kPa (1 kgf/cm2, 14 psi) for the absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for the relative pressure, the data has not been received.*2
    ID 2 Tire Inflation Pressure
    ID2 tire inflation pressure /
    min.: Absolute pressure / 100.00 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure / 449.35 kPa (4.5 kgf/cm2, 63 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi)
    Actual tire inflation pressure
    If 100 kPa (1 kgf/cm2, 14 psi) for the absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for the relative pressure, the data has not been received.*2
    ID 3 Tire Inflation Pressure
    ID3 tire inflation pressure /
    min.: Absolute pressure / 100.00 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure / 449.35 kPa (4.5 kgf/cm2, 63 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi)
    Actual tire inflation pressure
    If 100 kPa (1 kgf/cm2, 14 psi) for the absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for the relative pressure, the data has not been received.*2
    ID 4 Tire Inflation Pressure
    ID4 tire inflation pressure /
    min.: Absolute pressure / 100.00 kPa (1 kgf/cm2, 14 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi)
    max.: Absolute pressure / 449.35 kPa (4.5 kgf/cm2, 63 psi), Relative pressure / 349.35 kPa (3.6 kgf/cm2, 51 psi)
    Actual tire inflation pressure
    If 100 kPa (1 kgf/cm2, 14 psi) for the absolute pressure or 0 kPa (0 kgf/cm2, 0 psi) is displayed for the relative pressure, the data has not been received.*2
    ID 5 Tire Inflation Pressure
    -
    -
    -
    ID 1 Temperature in Tire
    ID1 temperature in tire/
    min.: -50°C (-58°F),
    max.: 205°C (401°F)
    Actual tire temperature
    If -50°C (-58°F) is displayed, the data has not been received.
    ID 2 Temperature in Tire
    ID2 temperature in tire/
    min.: -50°C (-58°F),
    max.: 205°C (401°F)
    Actual tire temperature
    If -50°C (-58°F) is displayed, the data has not been received.
    ID 3 Temperature in Tire
    ID3 temperature in tire/
    min.: -50°C (-58°F),
    max.: 205°C (401°F)
    Actual tire temperature
    If -50°C (-58°F) is displayed, the data has not been received.
    ID 4 Temperature in Tire
    ID4 temperature in tire/
    min.: -50°C (-58°F),
    max.: 205°C (401°F)
    Actual tire temperature
    If -50°C (-58°F) is displayed, the data has not been received.
    ID 5 Temperature in Tire
    -
    -
    -
    ID 1 Battery Voltage
    ID1 battery voltage/
    OVER or LESS
    OVER
    -
    ID 2 Battery Voltage
    ID2 battery voltage/
    OVER or LESS
    OVER
    -
    ID 3 Battery Voltage
    ID3 battery voltage/
    OVER or LESS
    OVER
    -
    ID 4 Battery Voltage
    ID4 battery voltage/
    OVER or LESS
    OVER
    -
    ID 5 Battery Voltage
    -
    -
    -
    ID 1 Initial Threshold of Low-pressure
    ID1 initial threshold of low pressure (Absolute pressure) /
    min.: 100.00 kPa (1 kgf/cm2, 14 psi)
    max.: 449.35 kPa (4.5 kgf/cm2, 63 psi)
    Tire pressure after initialization
    -
    ID 2 Initial Threshold of Low-pressure
    ID2 initial threshold of low pressure (Absolute pressure) /
    min.: 100.00 kPa (1 kgf/cm2, 14 psi)
    max.: 449.35 kPa (4.5 kgf/cm2, 63 psi)
    Tire pressure after initialization
    -
    ID 3 Initial Threshold of Low-pressure
    ID3 initial threshold of low pressure (Absolute pressure) /
    min.: 100.00 kPa (1 kgf/cm2, 14 psi)
    max.: 449.35 kPa (4.5 kgf/cm2, 63 psi)
    Tire pressure after initialization
    -
    ID 4 Initial Threshold of Low-pressure
    ID4 initial threshold of low pressure (Absolute pressure) /
    min.: 100.00 kPa (1 kgf/cm2, 14 psi)
    max.: 449.35 kPa (4.5 kgf/cm2, 63 psi)
    Tire pressure after initialization
    -
    ID 5 Initial Threshold of Low-pressure
    -
    -
    -
    Number of DTC
    Number of DTCs recorded/
    min.: 0
    max.: 255
    0
    -

    HINT:
    1. *1: Displayed only when the ID No. is not registered.
    2. *2: It may take about 5 or 6 minutes until the values are displayed. If the values are not displayed after a few minutes, perform troubleshooting according to the inspection procedure for DTCs C2121/21 to C2124/24 (Click here).


PERFORM ACTIVE TEST

HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Turn the ignition switch off.

  2. Connect the Techstream to the DLC3.

  3. Turn the ignition switch to ON and the Techstream on.

  4. Enter the following menus: Body / Combination Meter / Active Test.

  5. According to the display on the tester, perform the "Active Test".

    Combination Meter 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Indicat. Tire Pressure Warning System
    Tire pressure warning light
    ON or OFF
    Perform the test with the vehicle stopped and engine idling