Home › ENGINE ยท 1UR-FE › FUEL › FUEL TANK

FUEL TANK > INSTALLATION

for Preparation Click here



1. INSTALL NO. 1 FUEL TANK PROTECTOR (w/ Cover)

HINT:
Only perform this procedure when replacement of the No. 1 fuel tank protector is necessary.

  1. Attach the 4 clamps to install a new No. 1 fuel tank protector.



2. INSTALL FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY
  1. Apply a light coat of gasoline to a new gasket, and install it to the fuel tank.



    A152236E01
  1. Align the protrusion of the pump and gauge tube with the groove of the fuel tank.

  1. Install the fuel suction with pump and gauge tube into the fuel tank.

    NOTICE:
    Be careful not to bend the arm of the fuel sender gauge.

  1. Put the retainer on the fuel tank. While holding the fuel suction with pump and gauge tube, tighten the retainer one complete turn by hand.



    A259584E01
  1. Set SST on the retainer.

    SST
    09808-14030  

    HINT:
    1. Hold the fuel suction tube assembly upright by hand to ensure that the fuel suction tube gasket is not moved out of position.
    2. Securely attach the claws of SST to the protrusions of the retainer and fix SST in place.
    3. Install SST while pressing the claws of SST against the retainer (toward the center of SST).



    A259587E01
  1. Using SST, tighten the retainer until the mark on the retainer is within range A on the fuel tank as shown in the illustration.

    SST
    09808-14030  

    HINT:
    Fit the tips of SST onto the ribs of the retainer.



    A152247
  1. Install the 2 fuel tank tubes with the 2 tube joint clips.

    NOTICE:
    A118171E02
    1. Check that there are no scratches or foreign objects on the connecting parts.
    2. Check that the fuel tube joints are inserted securely.
    3. Check that the tube joint clips are on the collars of the fuel tube joints.
    4. After installing the tube joint clips, check that the fuel tube joints have not been pulled off.



3. INSTALL FUEL TANK TO FILLER PIPE HOSE
  1. Install the fuel tank to filler pipe hose to the fuel tank assembly.



4. INSTALL NO. 1 FUEL TANK HEAT INSULATOR
  1. Install the No. 1 fuel tank heat insulator with the 4 clips and nut.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



5. INSTALL INLET FUEL TANK PIPE SUB-ASSEMBLY
  1. Install the inlet fuel tank pipe sub-assembly with the 2 nuts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



6. INSTALL FUEL TANK ASSEMBLY
  1. Set the fuel tank assembly on a transmission jack and raise the fuel tank assembly.

  1. Attach the wire harness clamp and connect the fuel pump and fuel sender gauge connector to the fuel tank assembly.

    NOTICE:
    Be careful not to cut the wiring.

  1. w/ Cover:
    Attach the 3 claws to install the No. 2 fuel tank protector.

  1. Raise the transmission jack.

  1. Install the No. 1 fuel tank band sub-assembly and No. 2 fuel tank band sub-assembly with the 2 pins and 2 clips.

  1. Connect the No. 1 fuel tank band sub-assembly and No. 2 fuel tank band sub-assembly with the 2 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



7. CONNECT OUTLET NO. 1 CHARCOAL CANISTER HOSE


A152253E03
  1. Connect the outlet No. 1 charcoal canister hose to the inlet fuel tank pipe sub-assembly.
    Text in Illustration 
    *1
    Pipe
    *2
    Retainer
    *3
    Connector
    *4
    O-Ring
    *5
    Nylon Tube
    *a
    Push

  1. Attach the hose to the No. 1 breather tube support.



8. CONNECT FUEL TANK TO FILLER PIPE HOSE
  1. Connect the fuel tank to filler pipe hose to the inlet fuel tank pipe sub-assembly.

  1. Connect the fuel tank breather tube to the inlet fuel tank pipe sub-assembly.

    HINT:
    Push the parts together firmly until a "click" sound is heard.

    NOTICE:
    1. Before installing the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.
    1. After the connection, check if the connectors and pipes are securely connected by trying to pull them apart.

  1. Attach the lock claws to the connector by pushing down on the cover as shown in the illustration.

  1. Attach the filler pipe hose and fuel tank breather tube to the No. 1 breather tube clamp.



9. CONNECT WIRE HARNESS
  1. Attach the harness clamp to the fuel tank assembly.



10. CONNECT VENT LINE HOSE
  1. Connect the vent line hose and install the retainer.

    NOTICE:
    1. Before installing the hose, make sure that it is not damaged. Make sure that there is no foreign matter present on the connecting surfaces.
    1. After connecting, check if the hose and the connector are securely connected by pulling on them.



11. CONNECT FUEL TANK RETURN TUBE


A152241E03
  1. Connect the fuel tank return tube.
    Text in Illustration 
    *1
    Pipe
    *2
    Retainer
    *3
    Connector
    *4
    O-Ring
    *5
    Nylon Tube
    *a
    Push

    HINT:
    Push the parts together firmly until a "click" sound is heard.

    NOTICE:
    1. Before installing the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.
    1. After the connection, check if the connectors and pipes are securely connected by trying to pull them apart.

  1. Attach the lock claws to the connector by pushing down on the cover as shown in the illustration.



12. CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY


A159751E03
  1. Connect the fuel tank main tube sub-assembly.
    Text in Illustration 
    *1
    Pipe
    *2
    Retainer
    *3
    Connector
    *4
    O-Ring
    *5
    Nylon Tube
    *a
    Push

    HINT:
    Push the parts together firmly until a "click" sound is heard.

    NOTICE:
    1. Before installing the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.
    1. After the connection, check if the connectors and pipes are securely connected by trying to pull them apart.

  1. Attach the lock claws to the connector by pushing down on the cover as shown in the illustration.



13. INSTALL NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY (for Rough Road Area Specification Vehicles)
  1. Install the No. 1 fuel tank protector sub-assembly with the 2 bolts and 2 nuts.

    Torque:
    for bolt:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }
    for nut:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



14. INSTALL FUEL TANK CAP


15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


16. INSPECT FOR FUEL LEAK
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and Techstream main switch on.

    NOTICE:
    Do not start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

  1. Check that there are no fuel leaks after doing maintenance anywhere on the fuel system.