FUEL TANK > REMOVAL |
| 1. PRECAUTION |
| 2. DISCHARGE FUEL SYSTEM PRESSURE |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the fuel pump ECU connector (Click here).
Connect the cable to the negative (-) battery terminal.
Start the engine. After the engine has stopped on its own, turn the ignition switch off.
Crank the engine again, and then check that the engine does not start.
Loosen the fuel tank cap, and then discharge the pressure in the fuel tank completely.
Connect the fuel pump ECU connector (Click here).
| 3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 4. REMOVE FUEL TANK CAP |
| 5. REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY (for Rough Road Area Specification Vehicles) |
Remove the 2 bolts, 2 nuts and No. 1 fuel tank protector sub-assembly.
| 6. DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY |
![]() |
Detach the lock claw by lifting up the cover as shown in the illustration.
| *1 | Pipe |
| *2 | Retainer |
| *3 | Connector |
| *4 | O-Ring |
| *5 | Nylon Tube |
| *a | Lifting Up |
Pinch and pull the fuel tank main tube connector to disconnect the fuel tank main tube sub-assembly from the pipe.
| 7. DISCONNECT FUEL TANK RETURN TUBE |
![]() |
Detach the lock claw by lifting up the cover as shown in the illustration.
| *1 | Pipe |
| *2 | Retainer |
| *3 | Connector |
| *4 | O-Ring |
| *5 | Nylon Tube |
| *a | Lifting Up |
Pinch and pull the fuel tank return tube connector to disconnect the fuel tank return tube from the pipe.
| 8. DISCONNECT VENT LINE HOSE |
![]() |
Pull up the retainer and disconnect the vent line hose.
| *a | Up |
| 9. DISCONNECT WIRE HARNESS |
![]() |
Detach the harness clamp from the fuel tank assembly.
| 10. DISCONNECT FUEL TANK TO FILLER PIPE HOSE |
![]() |
Detach the lock claw by lifting up the cover as shown in the illustration.
| *1 | Pipe |
| *2 | Retainer |
| *3 | Connector |
| *4 | O-Ring |
| *5 | Nylon Tube |
| *a | Lifting Up |
Disconnect the fuel tank breather tube from the inlet fuel tank pipe sub-assembly.
Disconnect the fuel tank to filler pipe hose from the inlet fuel tank pipe sub-assembly.
Detach the filler pipe hose and fuel tank breather tube from the No. 1 breather tube clamp.
| 11. DISCONNECT OUTLET NO. 1 CHARCOAL CANISTER HOSE |
Disconnect the outlet No. 1 charcoal canister hose from the inlet fuel tank pipe sub-assembly.
Detach the hose from the No. 1 breather tube support.
| 12. REMOVE FUEL TANK ASSEMBLY |
Set a transmission jack underneath the fuel tank assembly.
![]() |
Remove the 2 bolts, 2 clips, 2 pins, No. 1 fuel tank band sub-assembly and No. 2 fuel tank band sub-assembly.
Slowly lower the transmission jack slightly.
![]() |
w/ Cover:
Detach the 3 claws to remove the No. 2 fuel tank protector.
![]() |
Detach the wire harness clamp from the fuel tank assembly as shown in the illustration.
Disconnect the fuel pump and fuel sender gauge connector and lower the transmission jack.
| 13. REMOVE INLET FUEL TANK PIPE SUB-ASSEMBLY |
![]() |
Remove the 2 nuts and inlet fuel tank pipe sub-assembly.
| 14. REMOVE NO. 1 FUEL TANK HEAT INSULATOR |
![]() |
Remove the nut from the No. 1 fuel tank heat insulator.
| *1 | Nut |
Using needle-nose pliers, remove the 4 clips shown in the illustration and then remove the No. 1 fuel tank heat insulator.
| 15. REMOVE FUEL TANK TO FILLER PIPE HOSE |
![]() |
Remove the fuel tank to filler pipe hose from the fuel tank assembly.
| 16. REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY |
![]() |
Remove the 2 tube joint clips and pull out the 2 fuel tank tubes.
![]() |
Set SST on the retainer.
![]() |
Using SST, loosen the retainer.
Remove the retainer.
Remove the fuel suction with pump and gauge tube assembly from the fuel tank.
Remove the gasket from the fuel tank.
| 17. REMOVE NO. 1 FUEL TANK PROTECTOR (w/ Cover) |
![]() |
Detach the 4 clamps to remove the No. 1 fuel tank protector.