Home › ENGINE ยท 3UR-FE › FUEL › FUEL TANK

FUEL TANK > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



2. DISCHARGE FUEL SYSTEM PRESSURE

CAUTION:
  1. Do not disconnect any part of the fuel system until you have discharged the fuel system pressure.
  2. After discharging the fuel pressure, place a cloth or equivalent over fittings as you separate them to reduce the risk of fuel spray on yourself or in the engine compartment.

  1. Disconnect the cable from the negative (-) battery terminal.

  1. Disconnect the fuel pump ECU connector (Click here).

  1. Connect the cable to the negative (-) battery terminal.

  1. Start the engine. After the engine has stopped on its own, turn the ignition switch off.

    HINT:
    DTC P0171/0174 (system too lean) may be set.

  1. Crank the engine again, and then check that the engine does not start.

  1. Loosen the fuel tank cap, and then discharge the pressure in the fuel tank completely.

  1. Connect the fuel pump ECU connector (Click here).



3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


4. REMOVE FUEL TANK CAP


5. REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY (for Rough Road Area Specification Vehicles)
  1. Remove the 2 bolts, 2 nuts and No. 1 fuel tank protector sub-assembly.



6. DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY


A159750E01
  1. Detach the lock claw by lifting up the cover as shown in the illustration.

  1. Pinch and pull the main tube connector to disconnect the connector from the pipe.

    NOTICE:
    1. Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.
    2. Do not use any tools to separate the pipe and connector.
    3. Do not forcefully bend or twist the nylon tube.
    4. Check for foreign matter on the pipe seal surface. Clean if necessary.
    5. Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.
    6. If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.



7. DISCONNECT FUEL TANK RETURN TUBE


A152240E01
  1. Detach the lock claw by lifting up the cover as shown in the illustration.

  1. Pinch and pull the return tube connector to disconnect the connector from the pipe.

    NOTICE:
    1. Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.
    2. Do not use any tools to separate the pipe and connector.
    3. Do not forcefully bend or twist the nylon tube.
    4. Check for foreign matter on the pipe seal surface. Clean if necessary.
    5. Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.
    6. If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.



8. DISCONNECT VENT LINE HOSE


    A152244E01
  1. Pull up the retainer and disconnect the vent line hose.

    NOTICE:
    1. Do not use any tools in this procedure.
    1. Check for any dirt and foreign matter contamination in the valve and around the connector. Clean if necessary. Foreign matter may damage the O-rings or cause leaks in the seal between the valve and connector.



9. DISCONNECT WIRE HARNESS


    A152242
  1. Detach the harness clamp from the fuel tank assembly.



10. DISCONNECT FUEL TANK TO FILLER PIPE HOSE


    A152252E01
  1. Detach the lock claw by lifting up the cover as shown in the illustration.

  1. Disconnect the fuel tank breather tube from the inlet fuel tank pipe sub-assembly.

  1. Disconnect the fuel tank to filler pipe hose from the inlet fuel tank pipe sub-assembly.

  1. Detach the filler pipe hose and fuel tank breather tube from the No. 1 breather tube clamp.



11. DISCONNECT OUTLET NO. 1 CANISTER HOSE
  1. Disconnect the outlet No. 1 canister hose from the inlet fuel tank pipe sub-assembly.

  1. Detach the hose from the No. 1 breather tube clamp.



12. REMOVE FUEL TANK ASSEMBLY
  1. Set a mission jack underneath the fuel tank assembly.



    A152248
  1. Remove the 2 bolts, 2 clips, 2 pins, No. 1 fuel tank band sub-assembly and No. 2 fuel tank band sub-assembly.

  1. Slowly lower the mission jack slightly.

    NOTICE:
    Be careful not to cut the wirings.



    A307675
  1. w/ Cover:
    Detach the 3 claws and remove the No. 2 fuel tank protector.



    A152243
  1. Detach the wire harness clamp from the fuel tank assembly as shown in the illustration.

  1. Disconnect the fuel pump connector and lower the mission jack.

    NOTICE:
    1. Before this procedure, check the connector for dirt, mud or other contamination.
    2. Do not use any tools in this procedure.



13. REMOVE INLET FUEL TANK PIPE SUB-ASSEMBLY


    A156396
  1. Remove the 2 nuts and inlet fuel tank pipe sub-assembly.



14. REMOVE NO. 1 FUEL TANK HEAT INSULATOR


A152249E01
  1. Remove the nut from the No. 1 fuel tank heat insulator.

  1. Using needle-nose pliers, remove the 4 clips shown in the illustration and then remove the No. 1 fuel tank heat insulator.



15. REMOVE FUEL TANK TO FILLER PIPE HOSE


    A152251
  1. Remove the fuel tank to filler pipe hose from the fuel tank assembly.



16. REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY


    A152246E01
  1. Remove the 2 tube joint clips and pull out the fuel tank main tube sub-assembly and fuel tank return tube.

    NOTICE:
    1. Remove any dirt and foreign matter on the fuel tube joint before performing this work.
    2. Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.
    3. Perform this work by hand. Do not use any tools.
    4. Do not forcibly bend, twist or turn the nylon tube.
    5. Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the fuel tank tubes.



    A259584E01
  1. Set SST on the retainer.

    SST
    09808-14030  

    HINT:
    1. Securely attach the claws of SST to the protrusion of the retainer and fix SST in place.
    2. Install SST while pressing the claws of SST against the retainer (towards the center of SST).



    A259581E01
  1. Using SST, loosen the retainer.

    SST
    09808-14030  

    NOTICE:
    1. Do not use any tools other than those specified in this operation. Damage to the retainer or the fuel tank assembly may result.
    2. While pressing down on SST so that the claws of SST do not slip off the protrusion of the retainer, turn the retainer counterclockwise to loosen it.

    HINT:
    The protrusions of the retainer fit in the ends of SST.

  1. Remove the retainer.

  1. Remove the fuel suction with pump and gauge tube assembly from the fuel tank assembly.

    NOTICE:
    Be careful not to bend the arm of the fuel sender gauge.

  1. Remove the gasket from the fuel tank assembly.



17. REMOVE NO. 1 FUEL TANK PROTECTOR (w/ Cover)


A307676

HINT:
Only perform this procedure when replacement of the No. 1 fuel tank protector is necessary.

  1. Detach the 4 clamps to remove the No. 1 fuel tank protector.