Home › ENGINE ยท 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P011B    Engine Coolant Temperature / Intake Air Temperature Correlation

for Preparation Click here


DESCRIPTION

The engine has two temperature sensors, an engine coolant temperature sensor and an intake air temperature sensor, to detect the temperature while the engine is in operation. A thermistor, whose resistance value varies according to the temperature, is built into each sensor. When the temperature is low, the resistance of the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are transmitted to the ECM as voltage changes. Based on the temperature signals output from these sensors, the ECM determines the fuel injection time and ignition timing to control the engine.

DTC No.
DTC Detection Condition
Trouble Area
P011B
  1. All conditions are met (2 trip detection logic):
    1. Battery voltage is 10.5 V or higher.
    2. 7 hours or more have elapsed from the engine stop of the previous trip.
    3. 736 seconds have elapsed after a cold engine start.
    4. Minimum intake air temperature after the engine start is higher than -10°C (14°F).
    5. Average engine coolant temperature before the engine start is higher than -10°C (14°F).
    6. Difference between the readings of the engine coolant temperature and intake air temperature is more than 20°C (36°F).
  1. Intake air temperature sensor
  2. Engine coolant temperature sensor
  3. ECM

A163149E98

HINT:
  1. Waiting is required to prevent the temperature of the engine from affecting the readings. If the engine has been operated recently, it will not be possible to accurately compare the readings.
  1. For diagnosis, in order to duplicate the detection conditions of the DTC, it is necessary to park and leave the vehicle for 7 hours. Leaving the vehicle for 7 hours ensures that the actual temperature of the engine coolant and intake air are very similar. When the vehicle has been left for less than 7 hours, differences in the readings may exist which do not necessarily indicate a fault.


MONITOR DESCRIPTION

The ECM monitors the difference between the engine coolant temperature and intake air temperature when the engine is started cold to detect the engine temperature conditions accurately. The monitor runs when the engine is started cold after 7 hours or more have elapsed since the engine was stopped (ignition switch turned to off) on the previous trip. If the difference between the engine coolant temperature and intake air temperature at a cold start is more than 20°C (36°F), the ECM interprets this as a malfunction in the engine coolant temperature sensor circuit or intake air temperature sensor circuit and stores the DTC.

MONITOR STRATEGY


Related DTCs
P011B: Engine coolant temperature/Intake air temperature sensor correlation
Required Sensors/Components (Main)
Engine coolant temperature/Intake air temperature sensor
Required Sensors/Components (Related)
-
Frequency of Operation
Once per driving cycle
Duration
-
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever these DTCs are not stored
P0112, P0113 (Intake Air Temperature Sensor)
P0115, P0117, P0118 (Engine Coolant Temperature Sensor)
P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control)
P2610 (Soak Timer)
Both conditions met
Conditions 1 and 2
1. All of following conditions met
Conditions (a), (b), (c) and (d)
(a) Time after ignition switch ON and engine not running
Less than 20 seconds
(b) Soak time
7 hours or more
(c) Battery voltage
10.5 V or higher
(d) Time after engine start
736 seconds or more
2. Either of the following conditions is met
Condition (a) and (b)
(a) Minimum intake air temperature after engine start
-10°C (14°F) or higher
(b) Engine coolant temperature before engine start
-10°C (14°F) or higher

TYPICAL MALFUNCTION THRESHOLDS


Deviated engine coolant temperature and intake air temperature
Below -20°C (-36°F) or higher than 20°C (36°F)

CONFIRMATION DRIVING PATTERN


A213993E23

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation) [A].
  4. Turn the ignition switch off.
  5. With the engine stopped, leave the vehicle as is for 7.5 hours or more [B].
  6. Start the engine and wait 15 minutes or more [C].
  7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].
  8. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  9. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  10. Input the DTC: P011B.
  11. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    If the judgment result shows INCOMPLETE or N/A, perform steps [A] through [D] again.

  12. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


INSPECTION PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO P011B)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.
    Result 
    Result
    Proceed to
    P011B is output
    A
    P011B and other DTCs are output
    B

    HINT:
    If any DTCs other than P011B are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.READ VALUE USING TECHSTREAM (INTAKE AIR TEMPERATURE)
  1. Leave the vehicle for 7 hours or more.

    HINT:
    It is necessary leave the vehicle for 7 hours or more to simulate conditions similar to the DTC detection conditions.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / All Data / Intake Air.

  1. Read the value displayed on the Techstream.

    OK:
    Difference between the intake air temperature and actual outside air temperature is within 10°C (18°F).

    HINT:
    1. Temperature readings on the vehicle's outside temperature gauge (if equipped) are not suitable for comparing to the intake air temperature reading. The outside temperature gauge has a significant delay built-in to prevent temperature swings from being displayed on its display. Use an accurate thermometer to determine the outside air temperature.
    2. Perform "Inspection After Repair" after replacing the mass air flow meter (Click here).



NG
REPLACE MASS AIR FLOW METER (Click here)
OK


3.READ VALUE USING TECHSTREAM (ENGINE COOLANT TEMPERATURE)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Primary / Coolant Temp.

  1. Read the value displayed on the Techstream.

    OK:
    The difference between the coolant temperature and actual outside air temperature is within 10°C (18°F).

    HINT:
    1. If the result is not as specified, check if there are heat sources such as a block heater in the engine compartment.
    2. Perform "Inspection After Repair" after replacing the mass air flow meter (Click here).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK

REPLACE ECM (Click here)