Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › OCCUPANT CLASSIFICATION SYSTEM

OCCUPANT CLASSIFICATION SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK OCCUPANT CLASSIFICATION ECU

H100909E46


Terminal No. (Symbols)
Wiring Color
Terminal Description
Condition
Specification
Y2-1 (+B) - Y2-3 (GND)
W - W-B
Battery
Ignition switch ON
11 to 14 V
Y2-2 (DIA) - Y2-3 (GND)
GR - W-B
Diagnosis (DLC3)
Ignition switch ON
Pulse generation
Y2-3 (GND) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
Y2-4 (FSR-) - Y2-3 (GND)
Y - W-B
Center airbag sensor communication ground line
Always
Below 1 Ω
Y2-5 (BGND) - Y2-3 (GND)
P - W-B
Passenger side buckle switch ground line
Always
Below 1 Ω
Y2-7 (IG2) - Y2-3 (GND)
B - W-B
Power source (IGN fuse)
Ignition switch ON
11 to 14 V
Y2-8 (FSR+) - Y2-4 (FSR-)
L - Y
Center airbag sensor communication line
Ignition switch ON
Pulse generation
Y2-9 (BSW) - Y2-5 (BGND)
G - P
Passenger side buckle switch line
Ignition switch ON, buckle switch ON
0.12 to 0.18 A
Ignition switch ON, buckle switch OFF
0.4 to 0.7 mA
Y1-1 (SGD1) - Y2-3 (GND)
G - W-B
Front occupant detection sensor LH ground line
Always
Below 1 Ω
Y1-2 (SGD2) - Y2-3 (GND)
O - W-B
Front occupant detection sensor RH ground line
Always
Below 1 Ω
Y1-3 (SGD3) - Y2-3 (GND)
W - W-B
Rear occupant detection sensor LH ground line
Always
Below 1 Ω
Y1-4 (SGD4) - Y2-3 (GND)
BR - W-B
Rear occupant detection sensor RH ground line
Always
Below 1 Ω
Y1-11 (SVC1) - Y1-1 (SGD1)
R - G
Front occupant detection sensor LH power supply line
Ignition switch ON, load is applied to front occupant detection sensor LH
4.5 to 5.1 V
Y1-12 (SVC2) - Y1-2 (SGD2)
W - O
Front occupant detection sensor RH power supply line
Ignition switch ON, load is applied to front occupant detection sensor RH
4.5 to 5.1 V
Y1-5 (SVC3) - Y1-3 (SGD3)
GR - W
Rear occupant detection sensor LH power supply line
Ignition switch ON, load is applied to rear occupant detection sensor LH
4.5 to 5.1 V
Y1-6 (SVC4) - Y1-4 (SGD4)
V - BR
Rear occupant detection sensor RH power supply line
Ignition switch ON, load is applied to rear occupant detection sensor RH
4.5 to 5.1 V
Y1-7 (SIG1) - Y1-1 (SGD1)
P - G
Front occupant detection sensor LH signal line
Ignition switch ON, load is applied to front occupant detection sensor LH
Pulse generation
Y1-8 (SIG2) - Y1-2 (SGD2)
L - O
Front occupant detection sensor RH signal line
Ignition switch ON, load is applied to front occupant detection sensor RH
Pulse generation
Y1-9 (SIG3) - Y1-3 (SGD3)
Y - W
Rear occupant detection sensor LH signal line
Ignition switch ON, load is applied to rear occupant detection sensor LH
Pulse generation
Y1-10 (SIG4) - Y1-4 (SGD4)
B - BR
Rear occupant detection sensor RH signal line
Ignition switch ON, load is applied to rear occupant detection sensor RH
Pulse generation
  1. If the result is not as specified, the ECU may have a malfunction.