DTC P0418 Secondary Air Injection System Control "A" Circuit |
DTC P0419 Secondary Air Injection System Control "B" Circuit |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0418 P0419 |
|
|
| P0418 P0419 |
|
|
| Related DTCs | P0418: Secondary air injection system air pump circuit range check (Bank 1) P0419: Secondary air injection system air pump circuit range check (Bank 2) |
| Required Sensors/Components (Main) | Air injection control driver |
| Required Sensors/Components (Related) | Air pump |
| Frequency of Operation | Once per drive cycle |
| Duration | 3 seconds |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not stored | - |
| Secondary air injection pump | Operating |
| Secondary air injection switching valve | Operating |
| Battery voltage | 8 V or more |
| Ignition switch | ON |
| Starter | OFF |
| Monitor runs whenever following DTCs not stored | - |
| Secondary air injection pump | Not operating |
| Secondary air injection switching valve | Not operating |
| Battery voltage | 8 V or more |
| Ignition switch | ON |
| Starter | OFF |
| Diagnostic signal duty ratio from air injection control driver | 11% or more, and 29% or less |
| Diagnostic signal duty ratio from air injection control driver | 70% or more, and 90% or less when secondary air injection system operating. 0% when secondary air injection system not operating. |
| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.CHECK HARNESS AND CONNECTOR (AIR PUMP - AIR INJECTION CONTROL DRIVER, BODY GROUND) |
Disconnect the D89 or D90 air pump connector.
Disconnect the D48 or D52 AID connector.
Disconnect the cable from the battery positive (+) terminal.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D89-2 (B)- D48-2 (VP) | Always | Below 1 Ω |
| D90-2 (+B) - D52-2 (VP2) | Always | Below 1 Ω |
| D48-1 (BATT) - Positive (+) battery cable | Always | Below 1 Ω |
| D52-1 (BAT2) - Positive (+) battery cable | Always | Below 1 Ω |
| D89-4 (E) - Body ground | Always | Below 1 Ω |
| D90-4 (GND) - Body ground | Always | Below 1 Ω |
| D89-2 (B) or D48-2 (VP) - Body ground | Always | 10 kΩ or higher |
| D90-2 (+B) or D52-2 (VP2) - Body ground | Always | 10 kΩ or higher |
| D48-1 (BATT) or Positive (+) battery cable - Body ground | Always | 10 kΩ or higher |
| D52-1 (BAT2) or Positive (+) battery cable - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 2.INSPECT AIR PUMP |
![]() |
Start the engine and warm it up.
Turn the ignition switch off.
Connect the 400 A probe of an ammeter to the positive (+) wire of the air pump.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream ON.
Start the engine.
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV1: OPEN, AIR PUMP 2: ON, ASV2: OPEN and AIR PUMP 1: OFF, ASV1: CLOSE, AIR PUMP 2: OFF, ASV2: CLOSE.
Measure the current while the air pump is on and off.
| Tester Operation | Air Pump | ASV | Specified Condition |
| AIR PUMP: ON, ASV: OPEN | ON | OPEN | 10 to 40 A |
| AIR PUMP: OFF, ASV: CLOSE | OFF | CLOSE | Below 1 A |
|
| ||||
| OK | ||
| ||
| 3.REPLACE AIR PUMP |
Replace the air pump (Click here).
| NEXT | |
| 4.CHECK WHETHER DTC OUTPUT RECURS |
Start the engine and warm it up.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream ON.
Clear DTCs (if set) (Click here).
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.
Start the engine after the Techstream initialization is finished.
Perform the System Check operation by pressing Next.
After operating the AIR system, perform the following to confirm the AIR system pending codes: Press the Exit button.
Check pending DTCs.
Turn the ignition switch off.
|
| ||||
| OK | ||
| ||