Home › ENGINE · 3UR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0451    Evaporative Emission Control System Pressure Sensor Range / Performance

DTC    P0452    Evaporative Emission Control System Pressure Sensor / Switch Low Input

DTC    P0453    Evaporative Emission Control System Pressure Sensor / Switch High Input

for Preparation Click here


DTC SUMMARY


DTC Code
Monitoring Item
Malfunction Detection Condition
Trouble Area
Detection Timing
Detection Logic
P0451
Canister pressure sensor abnormal voltage fluctuation
Sensor output voltage fluctuates frequently within a certain time period.
  1. Canister pump module
  2. Connector/wire harness
    (Canister pump module - ECM)
  3. EVAP system hose (pipe from air inlet port to canister pump module, canister filter, fuel tank vent hose)
  4. ECM
  1. EVAP monitoring (ignition switch off)
  2. Engine running
2 trip
Canister pressure sensor constant voltage
Sensor output voltage does not vary in a certain time period.
  1. EVAP monitoring (ignition switch off)
P0452
Canister pressure sensor low input
EVAP pressure less than 42.11009 kPa for 0.5 seconds.
  1. Canister pump module
  2. Connector/wire harness
    (Canister pump module - ECM)
  3. EVAP system hose (pipe from air inlet port to canister pump module, canister filter, fuel tank vent hose)
  4. ECM
  1. Ignition switch ON
  2. EVAP monitoring (ignition switch off)
1 trip
P0453
Canister pressure sensor high input
EVAP pressure more than 123.8 kPa for 0.5 seconds.
  1. Canister pump module
  2. Connector/wire harness
    (Canister pump module - ECM)
  3. EVAP system hose (pipe from air inlet port to canister pump module, canister filter, fuel tank vent hose)
  4. ECM
  1. Ignition switch ON
  2. EVAP monitoring (ignition switch off)
1 trip

HINT:
The canister pressure sensor is built into the canister pump module.


DESCRIPTION

The description can be found in the EVAP (Evaporative Emission) System .

MONITOR DESCRIPTION


A311003E03

  1. DTC P0451: Canister pressure sensor abnormal voltage fluctuation or being constant
    If the canister pressure sensor voltage output fluctuates rapidly for 10 seconds, the ECM stops the EVAP system monitor. The ECM interprets this as the canister pressure sensor voltage fluctuating, and stops the EVAP system monitor. The ECM then illuminates the MIL and stores the DTC. Alternatively, if the sensor voltage output does not change for 10 seconds, the ECM interprets this as the sensor being stuck, and stops the monitor. The ECM then illuminates the MIL and stores the DTC. (Both the malfunctions are detected by 2 trip detection logic.)
  2. DTC P0452: Canister pressure sensor voltage low
    If the canister pressure sensor output [pressure] is below 42.11009 kPa-a (315.9 mmHg-a), the ECM interprets this as an open or short circuit malfunction in the canister pressure sensor or its circuit, and stops the EVAP system monitor. The ECM then illuminates the MIL and sets the DTC (1 trip detection logic).
  3. DTC P0453: Canister pressure sensor voltage high
    If the canister pressure sensor output [pressure] is 123.8 kPa-a (928.4 mmHg-a) or more, the ECM interprets this as an open or short circuit malfunction in the canister pressure sensor or its circuit, and stops the EVAP system monitor. The ECM then illuminates the MIL and sets the DTC (1 trip detection logic).

MONITOR STRATEGY


Required Sensors/Components
Canister pump module
Frequency of Operation
Continuous
Duration
0.5 seconds: P0452 and P0453
Within 2 minutes: P0451 (sensor stuck)
Less than 15 seconds: P0451 (sensor noise)
MIL Operation
Immediate: P0452 and P0453
2 driving cycles: P0451
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


P0451 (Noise monitor): 
Monitor runs whenever following DTCs not present
None
Atmospheric pressure (absolute pressure)
70 to 111 kPa-a (525 to 833 mmHg-a)
Battery voltage
10.5 V or more
Intake air temperature
4.4 to 40°C (40 to 104°F)
Canister pressure sensor malfunction (P0452, P0453)
Not detected
Either of following conditions met
A or B
A. Engine condition
Running
B. Time after key off
5 or 7 or 9.5 hours

P0451 (Stuck monitor): 
Battery voltage
10.5 V or more
Intake air temperature
4.4 to 40°C (40 to 104°F)
Canister pressure sensor malfunction (P0452, P0453)
Not detected
Atmospheric pressure (absolute pressure)
70 to 111 kPa-a (525 to 833 mmHg-a)
Time after key off
5 or 7 or 9.5 hours

P0452 and P0453: 
Monitor runs whenever following DTCs not present
None
Battery voltage
8 V or more
Starter
OFF
Either of following conditions met
(a) or (b)
(a) Ignition switch
ON
(b) Soak timer
ON

TYPICAL MALFUNCTION THRESHOLDS


P0451: Canister pressure sensor noise 
Frequency that EVAP pressure change 0.3 kPa-g (2.25 mmHg-g) or more
10 times or more in 10 seconds

P0451: Canister pressure sensor stuck 
EVAP pressure change during reference pressure measurement
Less than 0.65 kPa (4.876 mmHg)

P0452: Canister pressure sensor low voltage 
EVAP pressure
Less than 42.11009 kPa-a (315.8679 mmHg-a)

P0453: Canister pressure sensor high voltage 
EVAP pressure
More than 123.76147 kPa-a (928.33489 mmHg-a)

CONFIRMATION DRIVING PATTERN


A199236E48

NOTICE:
  1. The Evaporative System Check (Automatic Mode) consists of 6 steps performed automatically by Techstream. It takes a maximum of approximately 24 minutes.
  2. Do not perform the Evaporative System Check when the fuel tank is more than 90% full because the cut-off valve may be closed, making the fuel tank leak check unavailable.
  3. Do not run the engine during this operation.
  4. When the temperature of the fuel is 35°C (95°F) or more, a large amount of vapor forms and any check results become inaccurate. When performing the Evaporative System Check, keep the fuel temperature below 35°C (95°F).

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Enter the following menu items: Powertrain / Engine and ECT / Data List / Intake Air.
  4. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  5. Turn the ignition switch off and wait for at least 30 seconds.
  6. Turn the ignition switch to ON and turn the Techstream on [A].
  7. Enter the following menu items: Powertrain / Engine and ECT / Utility / Evaporative System Check / Automatic Mode.
  8. After the Evaporative System Check is completed, check for All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All readiness.
  9. Input the DTC: P0451, P0452 or P0453.
  10. Check the DTC judgment result [B].

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit

    HINT:
    If the judgment result shows ABNORMAL, the system has a malfunction.

  11. If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A164731E20


INSPECTION PROCEDURE

NOTICE:
  1. When a vehicle is brought into the workshop, leave it as it is. Do not change the vehicle condition. For example, do not tighten the fuel cap.
  2. Do not disassemble the canister pump module.
  3. The Techstream is required to conduct the following diagnostic troubleshooting procedure.

1.CONFIRM DTC AND EVAP PRESSURE
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON (do not start the engine).

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / EVAP / Vapor Pressure Pump.

  1. Read the EVAP (Evaporative Emission) pressure displayed on the Techstream.

    Result 
    Display
    (DTC Output)
    Test Result
    Suspected Trouble Area
    Proceed to
    P0451
    -
    Canister pressure sensor
    C
    P0452
    Less than 42.11009 kPa-a (315.86779 mmHg-a)
    1. Wire harness/connector (ECM - Canister pressure sensor)
    2. Canister pressure sensor
    3. Short in ECM circuit
    A
    P0453
    More than 123.76147 kPa-a (928.33489 mmHg-a)
    1. Wire harness/connector (ECM - Canister pressure sensor)
    2. Canister pressure sensor
    3. Open in ECM circuit
    B



B
Go to step 4

C
GO TO EVAP SYSTEM (Click here)
A


2.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)
  1. Turn the ignition switch off.

  1. Disconnect the D74 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Result 
    Tester Connection
    Condition
    Specified Condition
    Suspected Trouble Area
    Proceed to
    D74-121 (PPMP) - Body ground
    Always
    10 Ω or less
    1. Wire harness/connector (ECM - Canister pressure sensor)
    2. Short in canister pressure sensor circuit
    A
    D74-121 (PPMP) - Body ground
    Always
    10 kΩ or more
    1. Wire harness/connector (ECM - Canister pressure sensor)
    2. Short in ECM circuit
    B



B
Go to step 7
A


3.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - ECM)
  1. Disconnect the R12 canister pump module connector.

  1. Disconnect the D74 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Result 
    Tester Connection
    Condition
    Specified Condition
    Suspected Trouble Area
    Proceed to
    D74-121 (PPMP) - Body ground
    Always
    10 kΩ or more
    Short in canister pressure sensor circuit
    A
    D74-121 (PPMP) - Body ground
    Always
    10 Ω or less
    Short in wire harness/connector (ECM - Canister pressure sensor)
    B



A
Go to step 5

B
Go to step 6

4.CHECK HARNESS AND CONNECTOR (CANISTER PUMP MODULE - BODY GROUND)
  1. Disconnect the R12 canister pump module connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:

    Tester Connection
    Condition
    Specified Condition
    R12-8 (SGND) - Body ground
    Always
    100 Ω or less

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:

    Tester Connection
    Switch Condition
    Specified Condition
    R12-6 (VCC) - Body ground
    Ignition switch ON
    4.5 to 5.5 V
    R12-7 (VOUT) - Body ground
    Ignition switch ON
    4.5 to 5.5 V


Result 
Test Result
Suspected Trouble Area
Proceed to
Voltage and resistance within standard ranges
Open in canister pressure sensor circuit
A
Voltage and resistance outside standard ranges
Open in wire harness/connector (ECM - Canister pressure sensor)
B


B
Go to step 6
A


5.REPLACE CANISTER PUMP MODULE


  1. Replace the canister pump module (Click here).

    NOTICE:
    1. When replacing canister pump module, check the canister pump module interior, canister interior and related pipes for water, fuel and other liquids. If liquids are present, check for disconnections and/or cracks in the following: 1) the pipe from the air inlet port to the canister pump module; 2) the canister filter; and 3) the fuel tank vent hose. If liquids are present in canister interior, replace canister and canister pump module together (replace canister assembly).
    2. Check for filter blockage in the canister assembly. If the charcoal filter inside the canister assembly is clogged, replace canister and canister pump module together (replace canister assembly).
    3. Check for filter blockage in the canister filter. If the canister filter has blockages, replace the canister filter.


    A289733E03



NEXT
Go to step 8

6.REPAIR OR REPLACE HARNESS OR CONNECTOR

HINT:
If the exhaust tailpipe has been removed, go to the next step before reinstalling it.



NEXT
Go to step 8

7.REPLACE ECM
  1. Replace the ECM (Click here).


NEXT


8.CHECK WHETHER DTC OUTPUT RECURS (AFTER REPAIR)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Wait for at least 60 seconds.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.

HINT:
If no pending DTCs are displayed on the Techstream, the repair has been successfully completed.


NEXT

COMPLETED