Home › TRANSMISSION ยท A750E AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION UNIT

AUTOMATIC TRANSMISSION UNIT > REASSEMBLY

for Preparation Click here



1. BEARING POSITION


  1. Check bearing position.


    D028813E02


    Bearing diameter:

    Mark
    Front Race Diameter Inside / Outside
    Thrust Bearing Diameter Inside / Outside
    Rear Race Diameter Inside / Outside
    A
    73.6 mm (2.90 in.) / 102.0 mm (4.02 in.)
    71.9 mm (2.83 in.) / 85.6 mm (3.37 in.)
    -
    B
    38.0 mm (1.50 in.) / 57.0 mm (2.24 in.)
    43.4 mm (1.71 in.) / 58.3 mm (2.30 in.)
    -
    C
    -
    55.7 mm (2.19 in.) / 76.4 mm (3.01 in.)
    53.7 mm (2.11 in.) / 74.0 mm (2.91 in.)
    D
    33.4 mm (1.31 in.) / 49.0 mm (1.93 in.)
    32.1 mm (1.26 in.) / 49.35 mm (1.94 in.)
    32.1 mm (1.26 in.) / 49.0 mm (1.93 in.)
    E
    -
    21.5 mm(0.846 in.) / 40.8 mm (1.61 in.)
    -
    F
    48.5 mm (1.91 in.) / 62.7 mm (2.47 in.)
    45.9 mm (1.81 in.) / 64.0 mm (2.52 in.)
    -



2. ASSEMBLE NO. 4 BRAKE PISTON AND BRAKE REACTION SLEEVE


    D028795E09
  1. Coat 2 new O-rings with ATF, and install them to the brake reaction sleeve.

  1. Coat 2 new O-rings with ATF, and install them to the No. 4 brake piston.

  1. Install the No. 4 brake piston to the reaction sleeve.



3. INSTALL NO. 4 BRAKE PISTON WITH BRAKE REACTION SLEEVE


D028080E03
  1. Install the No. 4 brake piston with brake reaction sleeve to the transmission case.

    NOTICE:
    1. Do not damage the O-rings.
    2. Make sure the No. 4 brake piston is underneath the brake reaction sleeve.



4. INSTALL 1ST AND REVERSE BRAKE PISTON


    D028081E03
  1. Coat a new O-ring with ATF.

  1. Install the O-ring on the 1st and reverse brake piston.

  1. With the spring seat of the piston facing upwards (the front side), place the piston in the transmission case.

    NOTICE:
    Be careful not to damage the O-ring.



    D028549E01
  1. Place the piston return spring onto the No. 4 brake piston.



5. INSTALL 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY


    D028082E01
  1. Place SST on the spring retainer, and compress the return spring.

    SST
    09350-30020   (09350-07050)

  1. Using SST, install the snap ring.

    SST
    09350-30020   (09350-07070)



6. INSTALL REAR PLANETARY GEAR ASSEMBLY


    D027947E01
  1. Install the thrust needle roller bearing.

    Thrust needle roller bearing diameter:
    Item
    Inside
    Outside
    Bearing
    45.9 mm (1.81 in.)
    64.0 mm (2.52 in.)



    D027946E03
  1. Install the thrust needle roller bearing.

  1. Coat the No. 9 thrust bearing race with petroleum jelly, and install it onto the rear planetary ring gear.

    Bearing and race diameter:
    Item
    Inside
    Outside
    Bearing
    21.5 mm (0.847 in.)
    40.8 mm (1.61 in.)
    Race
    48.5 mm (1.91 in.)
    62.7 mm (2.47 in.)



    D027945E01
  1. Install the rear planetary gear assembly.



7. INSPECT PACK CLEARANCE OF 1ST AND REVERSE BRAKE


    D027966E01
  1. Make sure the 1st and reverse brake piston moves smoothly when applying and releasing the compressed air into the transmission case.



    D029831E01
  1. Using a vernier caliper, measure the level difference (length A) between the upper surface of the 1st and reverse brake piston and the hitting surface of the No. 4 brake flange at both ends across a diameter, and calculate the average.

    NOTICE:
    The 1st and reverse brake piston must be installed tightly to the end face of the transmission case.

    HINT:
    Length A = 36.35 to 37.09 mm (1.43 to 1.46 in.)



    D029832E03
  1. Using a vernier caliper, measure the thickness (length B) of the 2 brake flanges, 7 No. 4 brake plates and 8 No. 4 brake discs altogether at both ends across a diameter, and calculate the average.

    HINT:
    Pack clearance = Length A - Length B - 0.25 mm to 1.8 mm (0.00984 to 0.0709 in.)
    Length B = 36.04 to 37.14 mm (1.42 to 1.46 in.)

    Standard pack clearance:
    0.8 to 1.1 mm (0.0315 to 0.0433 in.)

    If the pack clearance is outside the standard, select and install a brake flange that makes the pack clearance within the standard.

    H thickness:
    No.
    Thickness
    No.
    Thickness
    0
    0 mm (0 in.)
    8
    0.8 mm (0.0315 in.)
    2
    0.2 mm (0.00787 in.)
    10
    1.0 mm (0.0394 in.)
    4
    0.4 mm (0.0157 in.)
    12
    1.2 mm (0.0472 in.)
    6
    0.6 mm (0.0236 in.)
    14
    1.4 mm (0.0551 in.)



8. INSTALL NO. 4 BRAKE DISC


    D027944E01
  1. Install the 2 flanges, 8 discs and 7 plates.

    Install in order:
    F - D - P - D - P - D - P - D - P - D - P - D - P - D - P - D - F

    HINT:
    F = Flange
    D = Disc
    P = Plate



9. INSTALL BRAKE PLATE STOPPER SPRING


D027943E01


10. INSTALL REAR PLANETARY RING GEAR FLANGE SUB-ASSEMBLY


    D027965E05
  1. Install the No. 8 thrust bearing race, thrust needle roller bearing, No. 7 thrust bearing race and planetary ring gear flange to the intermediate shaft.

    Bearing and race diameter:
    Item
    Inside
    Outside
    No. 7 thrust bearing race
    33.4 mm (1.31 in.)
    49.0 mm (1.93 in.)
    Thrust needle roller bearing
    32.1 mm (1.26 in.)
    49.35 mm (1.94 in.)
    No. 8 thrust bearing race
    32.1 mm (1.26 in.)
    49.0 mm (1.93 in.)



11. INSTALL NO. 3 1-WAY CLUTCH ASSEMBLY


    D027964E01
  1. Install the 1-way clutch and 1-way clutch inner race to the intermediate shaft.



12. INSTALL INTERMEDIATE SHAFT


    D027942E01
  1. Install the intermediate shaft with No. 3 1-way clutch assembly to the case.



    D027927E03
  1. Using SST, install the snap ring.

    SST
    09350-30020   (09350-07050, 09350-07060)



13. INSTALL CENTER PLANETARY GEAR ASSEMBLY


    D027940E01
  1. Install the planetary sun gear and center planetary gear to the case.

  1. Coat the thrust bearing race with petroleum jelly, and install it onto the center planetary ring gear.

    Race diameter:
    Item
    Inside
    Outside
    Race
    53.7 mm (2.11 in.)
    74.0 mm (2.91 in.)



14. INSTALL NO. 2 BRAKE PISTON


    D028797E07
  1. Coat 2 new O-rings with ATF, and install them to the brake piston.

  1. Press the brake piston into the brake cylinder with both hands.

    NOTICE:
    Be careful not to damage the O-rings.

  1. Install the brake piston to the case.



15. INSTALL NO. 2 BRAKE DISC


D027938E04
  1. Install the brake piston return spring.

  1. Install the 3 plates, 3 discs and flange.

    Install in order:
    D - P - D - P - D - P - F

    HINT:
    D = Disc
    P = Plate
    F = Flange



    D028818E06
  1. Using SST and press, compress the return spring and install the No. 2 brake spring snap ring.

    SST
    09351-40010  



16. INSTALL NO. 1 BRAKE PISTON


    D028539E10
  1. Coat 2 new O-rings with ATF, and install them on the brake piston.

  1. Press the brake piston into the brake cylinder with both hands.

    NOTICE:
    Be careful not to damage the O-rings.



17. INSTALL BRAKE PISTON RETURN SPRING SUB-ASSEMBLY


    D027935E01
  1. Install the brake piston return spring and No. 1 brake piston with No. 1 brake cylinder on the transmission case.



18. INSTALL BRAKE PISTON RETURN SPRING SNAP RING


    D028819E04
  1. Using SST and a press, compress the return spring and install the brake piston return spring snap ring.

    SST
    09351-40010  



19. INSTALL NO. 1 BRAKE DISC


    D027933E04
  1. Install the 3 plates, 3 discs and flange.

    Install in order:
    P - D - P - D - P - D - F

    HINT:
    P = Plate
    D = Disc
    F = Flange



20. INSTALL CENTER PLANETARY RING GEAR


    D028541E01
  1. Install the center planetary ring gear and front planetary ring gear flange on the front planetary ring gear.



    D028540E01
  1. Using a screwdriver, install the snap ring.



21. INSTALL FRONT PLANETARY RING GEAR


    D027932E01
  1. Install the front planetary ring gear and thrust needle roller bearing on the case.

    Thrust needle roller bearing diameter:
    Item
    Inside
    Outside
    Bearing
    55.7 mm (2.19 in.)
    76.4 mm (3.01 in.)



22. INSTALL FRONT PLANETARY GEAR ASSEMBLY


    D027931E04
  1. Install the thrust needle roller bearing and thrust washer.

  1. Coat the thrust race with petroleum jelly, and install it onto the front planetary ring gear.

    Thrust needle roller bearing and race diameter:
    Item
    Inside
    Outside
    Bearing
    43.4 mm (1.71 in.)
    58.3 mm (2.30 in.)
    Race
    38.0 mm (1.50 in.)
    57.0 mm (2.24 in.)



    D027930E01
  1. Install the front planetary gear assembly and 1-way clutch inner race to the case.



23. INSPECT NO. 1 BRAKE PISTON


    D028814E01
  1. Make sure the No. 1 brake piston moves smoothly when applying and releasing the compressed air into the transmission case.



    D028815E01
  1. Using a feeler gauge, measure the B3 brake pack clearance between the snap ring and flange.

    Standard piston stroke:
    0.42 to 0.72 mm (0.0165 to 0.0283 in.)

    If the piston stroke is outside the specification, parts may have been assembled incorrectly. Perform the reassembly again. If the piston stroke is still outside the specification, select another flange.

    HINT:
    There are 4 different thicknesses for the flange.

    Flange thickness:
    No.
    Thickness
    No.
    Thickness
    0
    2.0 mm (0.0787 in.)
    2
    2.4 mm (0.0945 in.)
    1
    2.2 mm (0.0866 in.)
    3
    2.6 mm (0.102 in.)



24. INSTALL 2ND BRAKE PISTON


    D028546E11
  1. Coat 2 new O-rings with ATF, and install them to the 2nd brake piston.

  1. Press the 2nd brake cylinder into the 2nd brake piston with both hands.

    NOTICE:
    Be careful not to damage the O-rings.



    D028817E04
  1. Using SST and a press, compress the return spring and install the snap ring.

    SST
    09351-40010  

    NOTICE:
    Be sure the end gap of the snap ring is not aligned with the spring retainer claw.



25. INSTALL 2ND BRAKE CYLINDER


    D027929E01
  1. Install the 2nd brake cylinder to the case.



26. INSTALL 1-WAY CLUTCH ASSEMBLY


    D027928E01
  1. Install the thrust washer and 1-way clutch to the case.



27. INSTALL 2ND BRAKE PISTON HOLE SNAP RING


    D027927E03
  1. Using SST, install the snap ring.

    SST
    09350-30020   (09350-07060)



28. INSTALL NO. 3 BRAKE DISC


    D027926E05
  1. Install the cushion plate, 4 plates, 4 discs and flange to the case.

    Install in order:
    C - P - D - P - D - P - D - P - D - F

    HINT:
    C = Cushion
    P = Plate
    D = Disc
    F = Flange



29. INSTALL NO. 3 BRAKE SNAP RING


    D027925E01
  1. Using a screwdriver, install the snap ring.



30. INSTALL DIRECT CLUTCH PISTON SUB-ASSEMBLY


    D028816E02
  1. Coat 2 new O-rings with ATF, and install them to the direct clutch piston.



    D028517E01
  1. Install the No. 2 clutch balancer and direct clutch return spring to the direct clutch piston.



    D028516E02
  1. Coat a new O-ring with ATF, and install it on the clutch drum.

  1. Press the direct clutch piston into the clutch drum with both hands.

    NOTICE:
    Be careful not to damage the O-rings.



    D028514E05
  1. Place SST on the direct clutch piston, and compress the return spring with a press.

    SST
    09320-89010  
    09350-30020   (09350-07070)

    NOTICE:
    Stop pressing when the spring sheet is lowered to the place 1 to 2 mm (0.0393 to 0.0787 in.) from the snap ring groove to prevent the spring sheet from being deformed.

  1. Install the snap ring with a snap ring expander.

    NOTICE:
    Do not expand the snap ring excessively.



    D028536E07
  1. Set the end gap of the snap ring in the piston as shown in the illustration.

    NOTICE:
    Be sure the end gap of the snap ring is not aligned with the spring retainer claw.



31. INSTALL REVERSE CLUTCH PISTON SUB-ASSEMBLY


    D028513E02
  1. Coat a new O-ring with ATF, and install it on the clutch drum.



    D028512E02
  1. Coat a new O-ring with ATF, and install it on the reverse clutch piston.



    D028511E01
  1. Press the clutch drum sub-assembly into the reverse clutch piston with both hands.

    NOTICE:
    Be careful not to damage the O-ring.



32. INSTALL REVERSE CLUTCH RETURN SPRING SUB-ASSEMBLY


    D028510E02
  1. Coat a new O-ring with ATF, and install it on the reverse clutch piston.

  1. Install the reverse clutch return spring onto the reverse clutch piston.



33. INSTALL NO. 3 CLUTCH BALANCER


    D028509E04
  1. Place SST on the No. 3 clutch balancer, and compress the clutch balancer with a press.

    SST
    09387-00070  
    09350-30020   (09350-07070)

    NOTICE:
    Stop pressing when the spring sheet is lowered to the place 1 to 2 mm (0.0393 to 0.0787 in.) from the snap ring groove to prevent the spring sheet from being deformed.

  1. Install the snap ring with a snap ring expander.

    NOTICE:
    Do not expand the snap ring excessively.



    D028534E02
  1. Set the end gap of the snap ring in the piston as shown in the illustration.

    NOTICE:
    Be sure the end gap of the snap ring is not aligned with the spring retainer claw.



34. INSTALL DIRECT CLUTCH DISC


    C162137E01
  1. Install the 5 plates, 5 discs and reverse clutch flange on the clutch drum.

    Install in order:
    P - D - P - D - P - D - P - D - P - D - F

    HINT:
    P = Plate
    D = Disc
    F = Flange



    D028507E01
  1. Using a screwdriver, install the 2 hole snap rings on the clutch drum.



35. INSPECT PACK CLEARANCE OF DIRECT CLUTCH


    D029841E02
  1. Using a dial indicator, measure the moving distance (distance A) of the clutch flange at both ends across a diameter while blowing air from the oil hole as shown in the illustration, and calculate the average.

    Standard pack clearance:
    0.5 to 0.8 mm (0.0197 to 0.0315 in.)

    NOTICE:
    When measuring the moving distance, install a standard flange (thickness: 3.4 mm (0.134 in.)) to the position of the shaded area in the illustration.

    HINT:
    Flange moving distance A = 0.26 to 1.14 mm (0.0102 to 0.0449 in.)
    Pack clearance = Flange moving distance A - 0.05 mm (0.00197 in.)

    If the pack clearance is outside the standard, select and install a clutch flange that makes the pack clearance within the standard.

    Standard flange thickness:
    No.
    Thickness
    No.
    Thickness
    0
    3.0 mm (0.118 in.)
    5
    3.5 mm (0.138 in.)
    1
    3.1 mm (0.122 in.)
    6
    3.6 mm (0.142 in.)
    2
    3.2 mm (0.126 in.)
    7
    3.7 mm (0.146 in.)
    3
    3.3 mm (0.130 in.)
    8
    3.8 mm (0.150 in.)
    4
    3.4 mm (0.134 in.)
    -
    -



36. INSTALL REVERSE CLUTCH FLANGE


    D028506E01
  1. Install the reverse clutch flange to the clutch drum.



37. INSTALL REVERSE CLUTCH REACTION SLEEVE


    D031540E02
  1. Install the 5 reverse clutch discs, 4 clutch plates, reverse clutch flange, clutch cushion plate and reverse clutch reaction sleeve to the reverse clutch hub.

    Install in order:
    D - P - D - P - D - P - D - P - D - F - C - S

    HINT:
    D = Disc
    P = Plate
    F = Flange
    C = Cushion
    S = Sleeve

  1. Using a screwdriver, install the hole snap ring.



38. INSPECT PACK CLEARANCE OF REVERSE CLUTCH


  1. Using a dial indicator, measure the reverse clutch piston stroke (distance A) and the moving distance (distance B) of the reverse flange at the both ends across a diameter while blowing air (392 kPa, 4.0 kgf/cm2, 57 psi) from the oil hole as shown in the illustration, and calculate the average.

    Standard pack clearance:
    0.5 to 0.8 mm (0.0197 to 0.0315 in.)

    NOTICE:
    When measuring the moving distance, install a standard flange (thickness: 3.3 mm (0.130 in.)) to the position of the shaded area in the illustration.

    HINT:
    Piston stroke A = 1.05 to 2.15 mm (0.0413 to 0.0846 in.)
    Flange moving distance B = 0.72 to 1.08 mm (0.0283 to 0.0425 in.)
    Pack clearance = Piston stroke A to Flange moving distance B to 0.06 mm (0.00236 in.)



    D028538E02

    If the pack clearance is outside the standard, select and install a clutch flange that makes the pack clearance within the standard.

    Standard flange thickness:
    No.
    Thickness
    No.
    Thickness
    0
    2.8 mm (0.110 in.)
    6
    3.4 mm (0.134 in.)
    1
    2.9 mm (0.114 in.)
    7
    3.5 mm (0.138 in.)
    2
    3.0 mm (0.118 in.)
    8
    3.6 mm (0.142 in.)
    3
    3.1 mm (0.122 in.)
    9
    3.7 mm (0.146 in.)
    4
    3.2 mm (0.126 in.)
    A
    3.8 mm (0.150 in.)
    5
    3.3 mm (0.130 in.)
    -
    -



39. REMOVE REVERSE CLUTCH REACTION SLEEVE


    D029844E01
  1. Using a screwdriver, remove the snap ring from the clutch drum.



    D029843E01
  1. Remove the reverse clutch reaction sleeve, clutch cushion plate, reverse clutch flange, 5 reverse clutch discs, and 4 clutch plates from the reverse clutch hub.



40. INSTALL FORWARD CLUTCH PISTON


    D028525E02
  1. Coat 2 new O-rings with ATF, and install them on the forward clutch piston.



41. INSTALL NO. 1 CLUTCH BALANCER


    D028523E02
  1. Coat a new O-ring with ATF and install it on the clutch balancer.



    D028522E01
  1. Install the clutch balancer and forward clutch return spring.

    NOTICE:
    Be careful not to damage the O-ring.



    D028521E02
  1. Place SST on the No. 1 clutch balancer, and compress the return spring with a press.

    NOTICE:
    Stop pressing when the spring sheet is lowered to the place 1 to 2 mm (0.0393 to 0.0787 in.) from the snap ring groove to prevent the spring sheet from being deformed.

    SST
    09350-30020   (09350-07040, 09350-07070)

  1. Install the snap ring with a snap ring expander.

    NOTICE:
    Do not expand the snap ring excessively.

  1. Set the end gap of the snap ring in the piston as shown in the illustration.

    NOTICE:
    Be sure the end gap of the snap ring is not aligned with the spring retainer claw.



    D028535E02
  1. Set the end gap of the snap ring in the piston as shown in the illustration.



42. INSTALL FORWARD MULTIPLE DISC CLUTCH DISC


    D028520E02
  1. Install the 2 flanges, 6 discs and 5 plates to the input shaft assembly.

    Install in order:
    F- D - P - D - P - D - P - D - P - D - P - D - F

    HINT:
    F = Flange
    D = Disc
    P = Plate



    D028519E01
  1. Using a screwdriver, install the hole snap ring.



43. INSTALL INPUT SHAFT OIL SEAL RING


    D029677E01
  1. Coat 3 new oil seal rings with ATF.

  1. Squeeze the ends of the 3 oil seal rings together, and then install them to the starter shaft groove.

    NOTICE:
    Do not excessively widen the ring.

    HINT:
    After installing the oil seal rings, check that they rotate smoothly.



44. INSPECT PACK CLEARANCE OF FORWARD CLUTCH


    D028537E02
  1. Using a dial indicator, measure the moving distance (distance A) of the clutch flange at both ends across a diameter while blowing air from the oil hole as shown in the illustration, and calculate the average.

    Standard pack clearance:
    0.6 to 0.9 mm (0.0236 to 0.354 in.)

    NOTICE:
    When measuring the moving distance, install a standard flange (thickness: 3.4 mm (0.134 in.)) to the position of the shaded area in the illustration.

    HINT:
    Flange moving distance A = 0.26 to 1.36 mm (0.0102 to 0.0535 in.)
    Pack clearance = Flange moving distance A to 0.01 mm (0.000394 in.)

    If the pack clearance is outside the standard, select and install a clutch flange that makes the pack clearance within the standard.

    Standard flange thickness:
    No.
    Thickness
    No.
    Thickness
    0
    3.0 mm (0.118 in.)
    6
    3.6 mm (0.142 in.)
    1
    3.1 mm (0.122 in.)
    7
    3.7 mm (0.146 in.)
    2
    3.2 mm (0.126 in.)
    8
    3.8 mm (0.150 in.)
    3
    3.3 mm (0.130 in.)
    9
    3.9 mm (0.154 in.)
    4
    3.4 mm (0.134 in.)
    A
    4.0 mm (0.158 in.)
    5
    3.5 mm (0.138 in.)
    -
    -



45. INSTALL INPUT SHAFT ASSEMBLY


    D028505E01
  1. Install the input shaft to the clutch drum.



    D028504E01
  1. Install the thrust needle roller bearing to the clutch drum.

    Standard thrust needle roller bearing diameter:
    Item
    Inside
    Outside
    Bearing
    21.3 mm (0.839 in.)
    41.1 mm (1.62 in.)



46. INSTALL MULTIPLE DISC CLUTCH HUB


    D028503E05
  1. Install the No. 2 thrust bearing race and input shaft thrust bearing race rear to the multiple disc clutch hub.

    Standard bearing race diameter:
    Item
    Inside
    Outside
    No. 2 thrust bearing race
    38.4 mm (1.51 in.)
    63.0 mm (2.48 in.)
    Input shaft bearing race rear
    22.6 mm (0.890 in.)
    60.0 mm (2.36 in.)



    D028502E01
  1. Install the multiple disc clutch hub to the clutch drum.



47. INSTALL FORWARD CLUTCH HUB SUB-ASSEMBLY


    D028500E04
  1. Install the 2 thrust needle roller bearings to the forward clutch hub.

    Standard bearing and race diameter:
    Item
    Inside
    Outside
    Bearing A
    42.5 mm (1.67 in.)
    61.2 mm (2.41 in.)
    Bearing B
    33.3 mm (1.31 in.)
    56.6 mm (2.23 in.)



    D028001E01
  1. Install the forward clutch hub to the clutch drum.



48. INSTALL REAR CLUTCH DISC


    D027999E14
  1. Install the 5 discs, 4 plates, reverse clutch flange and clutch cushion plate to the reverse clutch hub.

    Install in order:
    D - P - D - P - D - P - D - P - D - F - C

    HINT:
    D = Disc
    P = Plate
    F = Flange
    C = Cushion plate



49. INSTALL REVERSE CLUTCH REACTION SLEEVE


    D027998E01
  1. Install the reverse clutch reaction sleeve to the reverse clutch hub.



50. INSTALL REVERSE CLUTCH HUB SUB-ASSEMBLY


    D027997E01
  1. Install the reverse clutch hub, to the clutch drum.



    D027996E01
  1. Using a screwdriver, install the snap ring on the clutch drum and input shaft.



51. INSTALL NO. 2 1-WAY CLUTCH ASSEMBLY


    D027994E01
  1. Coat the No. 2 clutch drum thrust washer with petroleum jelly and install it onto the clutch drum.

  1. Install the 1-way clutch assembly washer.



52. INSTALL CLUTCH DRUM AND INPUT SHAFT ASSEMBLY


    D027924E02
  1. Install the thrust needle roller bearing.

  1. Coat the race with petroleum jelly and install it onto the clutch drum and input shaft assembly.

    Thrust needle roller bearing and diameter:
    Item
    Inside
    Outside
    Bearing
    71.9 mm (2.83 in.)
    85.6 mm (3.37 in.)
    Race
    73.6 mm (2.90 in.)
    102.0 mm (4.02 in.)



    D029833E01
  1. Install the clutch drum and input shaft drum assembly onto the transmission case.



53. INSTALL OIL PUMP ASSEMBLY


    D028809E01
  1. Install the No. 1 thrust bearing race to the front oil pump.

    Thrust bearing race diameter:
    Item
    Inside
    Outside
    Race
    74.2 mm (2.92 in.)
    87.74 mm (3.45 in.)



    D028796E02
  1. Coat a new O-ring with ATF, and install it around the oil pump assembly.

  1. Place the oil pump through the input shaft, and align the bolt holes of the oil pump assembly with the transmission case.

  1. Hold the input shaft, and lightly press the oil pump body to slide the oil seal rings into the overdrive direct clutch drum.

    NOTICE:
    Do not excessively push on the oil pump, as the oil seal ring will stick to the direct clutch drum.



    D027921E01
  1. Install the 10 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



54. INSTALL MANUAL VALVE LEVER SHAFT OIL SEAL


    D028548E01
  1. Using SST, tap in 2 new oil seals.

    SST
    09350-30020   (09350-07110)

  1. Coat the lips of the oil seals with MP grease.



55. INSPECT INDIVIDUAL PISTON OPERATION


    D028547E02
  1. Check the operating sound while applying compressed air into the oil holes indicated in the illustration.

    HINT:
    When inspecting the O/D direct clutch, check with the C3 accumulator piston holes indicated in the illustration.
    If there is no sound, disassemble and check the installation condition of the parts.

    1. No. 2 clutch (C2)
    2. No. 3 clutch (C3)
    3. No. 1 clutch (C1)
    4. No. 3 brake (B3)
    5. No. 1 brake (B1)
    6. No. 2 brake (B2)
    7. No. 4 brake (B4)



56. INSTALL MANUAL VALVE LEVER SUB-ASSEMBLY


    D028798E02
  1. Install a new spacer to the manual valve lever.

  1. Install the manual valve lever shaft to the transmission case through the manual valve lever.



    D028799E01
  1. Using a hammer, tap in a new spring pin.



    D028800E01
  1. Align the manual valve lever indentation with the spacer hole, and stake them together with the punch.

  1. Check that the shaft rotates smoothly.



57. INSTALL PARKING LOCK PAWL SHAFT


    D028846E04
  1. Install the E-ring to the shaft.

  1. Install the parking lock pawl, shaft and spring.



58. INSTALL PARKING LOCK ROD SUB-ASSEMBLY


    D012709E01
  1. Connect the parking lock rod to the manual valve lever.



59. INSTALL PARKING LOCK PAWL BRACKET


    D012708E01
  1. Place the parking lock pawl bracket onto the transmission case and install the 3 bolts.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }



    D028801E03
  1. Move the manual valve lever to the P position, and confirm that the planetary ring gear is correctly locked up by the lock pawl.



60. INSTALL C-1 ACCUMULATOR VALVE


    D028802E06
  1. Coat a new O-ring with ATF, and install it to the piston.



    D028803E01
  1. Install the spring and accumulator valve to the hole.

    Accumulator spring:
    Spring
    Free length
    Outer diameter
    Color
    C-1 Inner
    30.40 mm (1.20 in.)
    11.40 mm (0.449 in.)
    Pink
    C-1 Outer
    48.76 mm (1.92 in.)
    16.60 mm (0.654 in.)
    Light green



61. INSTALL C-3 ACCUMULATOR PISTON


    D028802E07
  1. Coat 2 new O-rings with ATF, and install them to the piston.



    D028804E01
  1. Install the spring and accumulator piston to the hole.

    Accumulator spring:
    Spring
    Free length
    Outer diameter
    Color
    C-3 Inner
    44.0 mm (1.73 in.)
    14.0 mm (0.551 in.)
    Yellow
    C-3 Outer
    73.35 mm (2.89 in.)
    19.90 mm (0.784 in.)
    Red



62. INSTALL B-3 ACCUMULATOR PISTON


    D028802E08
  1. Coat 2 new O-rings with ATF, and install them to the piston.



    D028805E01
  1. Install the spring and accumulator piston to the hole.

    Accumulator spring:
    Spring
    Free length
    Outer diameter
    Color
    B-3
    70.5 mm (2.78 in.)
    19.7 mm (0.776 in.)
    Purple



63. INSTALL C-2 ACCUMULATOR PISTON


    D028802E09
  1. Coat 2 new O-rings with ATF, and install them to the piston.



    D028806E01
  1. Install the spring and accumulator piston to the hole.

    Accumulator spring:
    Spring
    Free length
    Outer diameter
    Color
    C-2
    62.0 mm (2.44 in.)
    15.9 mm (0.626 in.)
    White



64. INSTALL CHECK BALL BODY


    D027914E05
  1. Install the spring and check ball body.



65. INSTALL BRAKE DRUM GASKET


    D027969E01
  1. Install the 3 brake drum gaskets.



66. INSTALL TRANSMISSION CASE GASKET


    D027968E08
  1. Install the 3 transmission case gaskets.



67. INSTALL TRANSMISSION VALVE BODY ASSEMBLY


    C157293E01
  1. Align the groove of the manual valve with the pin of the lever.



    C157292E01
  1. Install the 19 bolts.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

    HINT:
    Each bolt length is indicated below.
    36 mm (1.42 in.) for bolt A
    25 mm (0.984 in.) for bolt B

  1. Install the detent spring and detent spring cover with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



68. INSTALL TRANSMISSION WIRE


    D027912E01
  1. Install a new O-ring to the transmission wire.

  1. Install the transmission wire harness.

  1. Install the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



    C125285E02
  1. Connect the 7 solenoid connectors.

  1. Install the 2 ATF temperature sensors.

  1. Install the 2 clamps and 2 bolts.

    Torque:
    for bolt A:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }
    for bolt B:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    HINT:
    Each bolt length is indicated below.
    12 mm (0.472 in.) for bolt A
    36 mm (1.42 in.) for bolt B



69. INSTALL VALVE BODY OIL STRAINER ASSEMBLY


    D012703E01
  1. Coat a new O-ring with ATF, and install it to the oil strainer.

  1. Install the oil strainer with the 4 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



70. INSTALL TRANSMISSION OIL CLEANER MAGNET


    D027992E02
  1. Install the 4 magnets.



71. INSTALL AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY
  1. Install a new gasket on the oil pan.

  1. Install the 20 bolts.

    Torque:
    4.4 N*m{ 45 kgf*cm , 39 in.*lbf }

  1. Install the drain plug.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



72. INSTALL AUTOMATIC TRANSMISSION EXTENSION HOUSING OIL SEAL


    D027978E03
  1. Using SST and a hammer, tap in a new oil seal.

    SST
    09710-30050  
    09950-70010   (09951-07100)



73. INSTALL EXTENSION HOUSING DUST DEFLECTOR


    D027979E01
  1. Using SST and a hammer, tap in a new dust deflector.

    SST
    09223-15020  
    09950-70010   (09951-07100)



74. INSTALL EXTENSION HOUSING SUB-ASSEMBLY


    D029874E01
  1. Install the thrust needle roller bearing and 2 bearing races.

  1. Using a snap ring expander, install the snap ring.



    D029875E01
  1. Using a feeler gauge, measure the clearance between the snap ring and the race.

    Standard clearance:
    0.05 to 0.33 mm (0.00197 to 0.0130 in.)

    1. If the clearance is outside the standard, select another race.

    HINT:
    There are 6 different thickness for the race.

    Race thickness:
    No.
    Thickness
    No.
    Thickness
    1
    3.7 mm (0.146 in.)
    4
    4.0 mm (0.158 in.)
    2
    3.8 mm (0.150 in.)
    5
    4.1 mm (0.161 in.)
    3
    3.9 mm (0.154 in.)
    6
    4.2 mm (0.165 in.)

  1. Clean the threads of the bolts and case.



    D027973E02
  1. Apply seal packing to the extension housing.

    Seal packing:
    Toyota Genuine Seal Packing 1281,
    Three Bond 1281 or equivalent

    Seal diameter:
    1.0 to 1.5 mm (0.0394 to 0.0591 in.)

  1. Apply adhesive to the threads of the 6 bolts.

    Adhesive:
    Toyota Genuine Adhesive 1344,
    Three Bond 1344 or equivalent



    D027972E03
  1. Install the extension housing with the 6 bolts.

    Torque:
    34 N*m{ 345 kgf*cm , 25 ft.*lbf }

    HINT:
    Each bolt length is indicated below.
    45 mm (1.77 in.) for bolt A
    35 mm (1.38 in.) for bolt B



75. INSTALL AUTOMATIC TRANSMISSION HOUSING


    C210181E01
  1. Clean the threads of the bolts and case with non-residue solvent.

  1. Install the transmission housing with the 10 bolts.

    Torque:
    for 14 mm head bolt A:
    34 N*m{ 345 kgf*cm , 25 ft.*lbf }
    for 17 mm head bolt B:
    57 N*m{ 581 kgf*cm , 42 ft.*lbf }
    for 14 mm head bolt C:
    34 N*m{ 345 kgf*cm , 25 ft.*lbf }



76. INSTALL AUTOMATIC TRANSMISSION BREATHER TUBE


    C117463E01
  1. Coat a new O-ring with ATF and install it to the breather tube.

  1. Install the breather tube with the 2 bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



77. INSTALL SPEED SENSOR


    C111258
  1. Coat 2 new O-rings with ATF, and install it to the speed sensor.

  1. Install the 2 speed sensors.

  1. Install the 2 bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



78. INSTALL OIL COOLER TUBE UNION


    C159633E01
  1. Coat 2 new O-rings with ATF, and install them to the 2 oil cooler tube unions.

  1. Install the 2 oil cooler tube unions.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }



79. INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY


D027903E01
  1. Install the park/neutral position switch onto the manual valve lever shaft, and temporarily install the adjusting bolt.

  1. Install a new lock washer and the nut.

    Torque:
    6.9 N*m{ 70 kgf*cm , 61 in.*lbf }



    C155873E01
  1. Push the control shaft rearward as much as possible.

  1. Return the control shaft lever 2 notches to the N position.



    D025795E10
  1. Align the neutral basic line with the switch groove as shown in the illustration, and tighten the adjusting bolt.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }



    D027990E01
  1. Using a screwdriver, bend the tabs of the lock washer.

    HINT:
    Bend at least 2 of the lock washer tabs.



80. INSTALL TRANSMISSION CONTROL SHAFT LEVER RH


    C155869
  1. Install the control shaft lever RH with the washer and nut.

    Torque:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }