WINDSHIELD GLASS > INSTALLATION |
| 1. INSTALL NO. 2 WINDSHIELD GLASS STOPPER |
Apply Primer G to the glass where the spacers will be installed.
Install 2 new stoppers onto the glass as shown in the illustration.

| Area | Specified Condition |
| a | 8.5 mm (0.334 in.) |
| 2. INSTALL NO. 1 WINDSHIELD GLASS STOPPER |
![]() |
Install 2 new stoppers to the vehicle body as shown in the illustration.
| 3. INSTALL WINDSHIELD GLASS ADHESIVE DAM |
Apply Primer G to the glass where the glass adhesive dams will be installed.
Remove the peeling paper from the adhesive part of the dam. While aligning the dam to the ceramic notch and dam reference line, install the dam (adhesive side) to the glass (Primer G area).

| Area | Specified Condition |
| a | 29.2 mm (1.15 in.) |
| 4. INSTALL UPPER WINDSHIELD OUTSIDE MOULDING |
![]() |
Using a brush or sponge, coat the edge of the glass and the contact surface with Primer G.
Install the windshield outside moulding, as shown in the illustration.
| Temperature | Usage Time Frame |
| 35°C (95°F) | 15 minutes |
| 20°C (68°F) | 1 hour 40 minutes |
| 5°C (41°F) | 8 hours |
| 5. INSTALL WINDSHIELD GLASS |
![]() |
Using a brush, apply Primer M to the exposed part of the vehicle body.
Using a brush or sponge, apply Primer G to the contact surface of the glass.

Apply adhesive to the glass.
Cut off the tip of the cartridge nozzle as shown in the illustration.
| Temperature | Usage Time Frame |
| 35°C (95°F) | 15 minutes |
| 20°C (68°F) | 1 hour 40 minutes |
| 5°C (41°F) | 8 hours |
Load the sealer gun with the cartridge.
Apply adhesive to the glass as shown in the illustration.

| Area | Specified Condition |
| a | 12.0 mm (0.472 in.) |
| b | 8.0 mm (0.315 in.) |
| c | 4.0 mm (0.157 in.) |
![]() |
Install the glass to the vehicle body.
Using suction cups, position the glass so that the matchmarks are aligned. Press it in gently along the rim.
Lightly press the outer surface of the glass to ensure that it is securely fit to the vehicle body.
Hold the glass in place securely with protective tape or equivalent until the adhesive hardens.
w/ Windshield Deicer:
Install the clip and connect the connector.
| 6. INSTALL WINDSHIELD MOULDING OUTSIDE |
![]() |
Install the windshield outside moulding, as shown in the illustration.
Apply Primer G to the windshield outside moulding area "a" shown in the illustration.
| 7. CHECK FOR LEAK AND REPAIR |
Conduct a leak test after the adhesive has completely hardened.
Seal any leaks with auto glass sealer.
| 8. INSTALL ROOF DRIP SIDE FINISH MOULDING CLIP |
Using a heat light, heat the clip installation areas on the vehicle body.
Remove the double-sided tape from the vehicle body.
Wipe off any tape adhesive residue with cleaner.
Using a heat light, heat the clips.
Remove the peeling paper from the face of the clips.
Install the clips in the positions shown in the illustration.

| 9. INSTALL ROOF DRIP SIDE FINISH MOULDING LH |
Attach the clip to install the moulding.

| 10. INSTALL ROOF DRIP SIDE FINISH MOULDING RH |
| 11. INSTALL REAR ROOF DRIP SIDE FINISH MOULDING LH |
Clean the vehicle body surface.
Using a heat light, heat the vehicle body surface.
Remove the double-sided tape from the vehicle body.
Wipe off any tape adhesive residue with cleaner.
If reusing the moulding:
Clean the moulding.
Using a heat light, heat the moulding.
Remove the double-sided tape from the moulding.
Wipe off any tape adhesive residue with cleaner.
![]() |
Apply new double-sided tape to the moulding, as shown in the illustration.
Install the moulding.
Using a heat light, heat the vehicle body and moulding.
Remove the peeling paper from the face of the moulding.
![]() |
Attach the clip to install the moulding.
| 12. INSTALL REAR ROOF DRIP SIDE FINISH MOULDING RH |
| 13. INSTALL ROOF HEADLINING ASSEMBLY |
Return the roof headlining to its original position.
| 14. INSTALL COAT HOOK |
![]() |
Assemble the coat hook as shown in the illustration.
Attach the clip to install the coat hook.
| 15. INSTALL ASSIST GRIP SUB-ASSEMBLY |
for Regular Cab, for Double Cab:
Install the assist grip .
for CrewMax:
Install the assist grip .
| 16. INSTALL VISOR HOLDER |
for Regular Cab:
Install the visor holder .
for Double Cab, w/o Illumination:
Install the visor holder .
for CrewMax, w/o Illumination:
Install the visor holder .
| 17. INSTALL VISOR ASSEMBLY LH |
for Regular Cab:
Install the visor .
for Double Cab:
Install the visor .
for CrewMax:
Install the visor .
| 18. INSTALL VISOR ASSEMBLY RH |
| 19. INSTALL NO. 1 ROOM LIGHT ASSEMBLY |
![]() |
Using a screwdriver, detach the 4 claws and 2 guides and remove the No. 1 room light lens.
| *1 | Tape |
![]() |
Detach the 2 clips and 3 guides and remove the No. 1 room light assembly.
| 20. INSTALL ROOF CONSOLE BOX ASSEMBLY |
for Short Type:
Install the roof console box (see page ).
for Long Type:
Install the roof console box (Click here).
| 21. INSTALL INNER REAR VIEW MIRROR ASSEMBLY |
w/ EC Mirror:
Install the inner rear view mirror .
w/o EC Mirror:
Install the inner rear view mirror .
| 22. INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror) |
![]() |
Attach the 2 claws of the inner rear view mirror stay holder cover to the mirror, and then slide the inner rear view mirror stay holder cover in the direction indicated by the arrow in the illustration to attach the 2 claws to the roof headlining and install the inner rear view mirror stay holder cover.
| 23. INSTALL FRONT PILLAR GARNISH LH |
Attach the clip to install the front pillar garnish LH.
Install the bolt.
![]() |
Attach the claw to close the cover.
| 24. INSTALL FRONT PILLAR GARNISH RH |
Attach the clip to install the front pillar garnish RH.
Install the front assist grip sub-assembly to the front pillar garnish RH with the 2 bolts.
![]() |
Attach the 2 claws to close the 2 assist grip covers.
| 25. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
| 26. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
| 27. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY |
![]() |
Push the ventilator louver in the direction indicated by the arrow in the illustration to attach 8 claws and 2 clips, and install the ventilator louver.
| 28. INSTALL FRONT FENDER TO COWL SIDE SEAL LH |
Attach the claw to install the cowl side seal.
| 29. INSTALL FRONT FENDER TO COWL SIDE SEAL RH |
| 30. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH |
![]() |
Stop the wiper motor at the automatic stop position.
Clean the wiper arm serration with a round file or equivalent.
Clean the wiper pivot serration with a wire brush.
![]() |
Install the wiper arm and blade with the nut. Make sure that the wiper arm and blade comes to the position shown in the illustration.
| Position | Specified Condition |
| A | 23.9 mm (0.941 in.) |
| B | 35.5 mm (1.40 in.) |
| 31. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH |
![]() |
Stop the wiper motor at the automatic stop position.
Clean the wiper arm serration with a round file or equivalent.
Clean the wiper pivot serration with a wire brush.
![]() |
Install the wiper arm and blade with the nut. Make sure that the wiper arm and blade comes to the position shown in the illustration.
| Position | Specified Condition |
| A | 11.5 mm (0.453 in.) |
| B | 29.8 mm (1.17 in.) |
Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and there is no interference with the vehicle body.