Home › ENGINE ยท 1GR-FE › COOLING › WATER PUMP

WATER PUMP > INSTALLATION

for Preparation Click here



1. INSTALL WATER PUMP ASSEMBLY


    A223007E01
  1. Install a new gasket and the water pump with the 17 bolts.

    Torque:
    for bolt A:
    47 N*m{ 479 kgf*cm , 35 ft.*lbf }
    for bolt B:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }
    for bolt C:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }



2. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY


    A226495E01
  1. Temporarily install the V-ribbed belt tensioner with the 5 bolts.

    Standard Bolt:
    Item
    Length
    A
    70 mm (2.76 in.)
    B
    33 mm (1.30 in.)

    Text in Illustration 
    V100135
    Bolt A
    V100136
    Bolt B

  1. Tighten bolts 1 and 2 in numerical order.

    Torque:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }

  1. Tighten the other bolts.

    Torque:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }



3. CONNECT COOLER COMPRESSOR ASSEMBLY
  1. Install the cooler compressor with the 2 stud bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



    A238276E01
  1. Install the 2 bolts and 2 nuts.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }

    HINT:
    Tighten the bolts and nuts in the order shown in the illustration to install the cooler compressor.

  1. Connect the cooler compressor connector.



4. INSTALL GENERATOR ASSEMBLY
(Click here)


5. CONNECT VANE PUMP ASSEMBLY
  1. Connect the vane pump with the 2 bolts.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }

  1. Attach the wire harness clamp.

  1. Connect the connector.



6. INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY
  1. for Separate Type:
    Install the 2 idler pulley cover plates, 2 No. 2 idler pulleys and 2 No. 2 idler pulley cover plates with the 2 bolts.

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }

  1. for Integrated Type:
    Install the 2 No. 2 idler pulleys with the 2 bolts.

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }



7. INSTALL WATER INLET HOUSING


    A223008
  1. Install a new O-ring to the water outlet pipe.

  1. Install a new gasket to the water pump.

  1. Apply soapy water to the gasket of the water outlet pipe.

  1. Install the water inlet with the 5 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the 5 water by-pass hoses.

  1. Connect the No. 2 oil cooler hose.

  1. Connect the oil cooler hose.

  1. Connect the throttle body connector.



8. CONNECT AIR TUBE
  1. Connect the air tube with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



9. INSTALL FAN SHROUD
  1. Install the fan pulley to the water pump assembly.

  1. Place the fan shroud together with the fan with fluid coupling between the radiator assembly and engine.

    NOTICE:
    Be careful not to damage the radiator core.



    A229548E02
  1. Align the paint marks on the heads of the water pump stud bolts with the paint marks of the same color on the outer edge of the fluid coupling flange and install the fan with fluid coupling to the water pump assembly.
    Text in Illustration 
    *1
    Paint Mark

  1. Temporarily install the fan with fluid coupling to the water pump assembly with the 4 nuts. Tighten the nuts as much as possible by hand.



    A151756
  1. Attach the 2 claws of the fan shroud to the radiator assembly as shown in the illustration.

  1. Install the fan shroud with the 2 bolts.

    Torque:
    6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

  1. Connect the reservoir hose to the radiator tank upper.

  1. Install the fan and generator V-belt .

  1. Tighten the 4 nuts of the fan with fluid coupling.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



10. INSTALL RADIATOR HOSE OUTLET


    A238133E01
  1. Connect the radiator hose outlet to the water inlet housing, and slide the clamp to secure the hose shown in the illustration.
    Text in Illustration 
    *a
    Upper
    *b
    Front



    A238134E01
  1. Install the radiator hose outlet to the radiator assembly, and slide the clamp to secure the hose shown in the illustration.
    Text in Illustration 
    *a
    Upper
    *b
    RH



11. INSTALL RADIATOR HOSE INLET


    A238132E01
  1. Connect the radiator hose inlet, and slide the 2 clamps to secure the hose as shown in the illustration.
    Text in Illustration 
    *a
    Upper
    *b
    LH
    *c
    Front



12. ADD ENGINE COOLANT
  1. Add engine coolant.

    Standard capacity:
    10.7 liters (11.3 US qts, 9.4 Imp. qts)

    NOTICE:
    Do not substitute plain water for engine coolant.

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    2. Press the No. 1 and No. 2 radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.

  1. Slowly pour coolant into the radiator reservoir until it reaches the FULL line.

  1. Install the reservoir cap.

  1. Install the radiator cap.*1

  1. Start the engine and stop it immediately.*2

  1. Allow approximately 10 seconds to pass. Then remove the radiator cap and check the coolant level. If the coolant level has decreased, add coolant.*3

  1. Repeat steps *1, *2 and *3 until the coolant level does not decrease.

    HINT:
    Be sure to perform this step while the engine is cold, as air in the inlet radiator hose will flow into the radiator if the engine is warmed up and the thermostat opens.

  1. Install the radiator cap.*4

  1. Set the air conditioning as follows.*5
    Measurement Condition 
    Item
    Condition
    Fan speed
    Any setting except off
    Temperature
    Toward WARM
    Air conditioning switch
    Off

  1. Start the engine, warm it up until the thermostat opens, and then continue to run the engine for several minutes to circulate the coolant.*6

    CAUTION:
    1. Wear protective gloves. Hot areas on the parts may injure your hands.
    2. Be careful of the fan.
    3. Be careful as the engine, radiator and radiator hoses are hot and can cause burns.

    NOTICE:
    1. Immediately after starting the engine, if the radiator reservoir does not have any coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the FULL line.
    2. Do not start the engine when there is no coolant in the radiator reservoir.
    3. Pay attention to the needle of the engine coolant temperature receiver gauge. Make sure that the needle does not show an abnormally high temperature.
    4. If there is not enough coolant, the engine may burn out or overheat.

    HINT:
    1. Press the inlet and outlet radiator hoses several times by hand to bleed air while warming up the engine.
    2. The thermostat opening timing can be confirmed by pressing the outlet radiator hose by hand and checking when the engine coolant starts to flow inside the hose.

  1. Stop the engine, wait until the engine coolant cools down to ambient temperature. Then remove the radiator cap and check the coolant level.*7

    CAUTION:
    Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. If the coolant level has decreased, add coolant and warm up the engine until the thermostat opens.*8

  1. If the coolant level has not decreased, check that the coolant level in the radiator reservoir is at the FULL line.
    If the coolant level is below the FULL line, repeat steps *4 through *8.
    If the coolant level is above the FULL line, drain coolant until the coolant level reaches the FULL line.



13. INSPECT FOR COOLANT LEAK

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.