Home › RESTRAINTS › SEAT BELT › SEAT BELT WARNING SYSTEM

SEAT BELT WARNING SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK COMBINATION METER ASSEMBLY


  1. Disconnect the J28 combination meter assembly connector.


    E177004E11

  2. Disconnect the J28 combination meter assembly connector.

  3. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    J28-2 (IG+) - Body ground
    P - Body ground
    Ignition power supply
    (IG signal)
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V
    J28-1 (B) - Body ground
    LG - Body ground
    Battery power supply
    Always
    11 to 14 V
    J28-24 (ES) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω

  4. Reconnect the J28 combination meter assembly connector.

  5. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    J28-30 (SI) - Body ground
    LG - Body ground
    Speed signal (input)
    Ignition switch ON, wheel turned slowly
    Pulse generation


CHECK CENTER AIRBAG SENSOR ASSEMBLY

C131032E20


Terminal No.
Terminal Symbol
Destination
P1-11
DBE+
Front seat inner belt assembly LH
P1-12
DBE-
Front seat inner belt assembly LH
Q1-12
FSP+
Occupant detection ECU
Q1-13
FSP-
Occupant detection ECU

CHECK OCCUPANT DETECTION ECU


  1. Measure the voltage according to the value(s) in the table below.


    H100909E45

    HINT:
    Since the occupant detection ECU uses waterproof connectors, the voltage and waveform cannot be inspected directly. Standard voltage readings and waveforms are indicated for reference only.


    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specification
    Y2-1 (+B) - Y2-3 (GND)
    W - W-B
    Battery
    Ignition switch ON
    11 to 14 V
    Y2-2 (DIA) - Y2-3 (GND)
    GR - W-B
    Diagnosis (DLC3)
    Ignition switch ON
    Pulse generation
    Y2-3 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    Y2-4 (FSR-) - Y2-3 (GND)
    Y - W-B
    Center airbag sensor communication ground line
    Always
    Below 1 Ω
    Y2-5 (BGND) - Y2-3 (GND)
    P - W-B
    Passenger side buckle switch ground line
    Always
    Below 1 Ω
    Y2-7 (IG2) - Y2-3 (GND)
    B - W-B
    Power source (IGN fuse)
    Ignition switch ON
    11 to 14 V
    Y2-8 (FSR+) - Y2-4 (FSR-)
    L - Y
    Center airbag sensor communication line
    Ignition switch ON
    Pulse generation
    Y2-9 (BSW) - Y2-5 (BGND)
    G - P
    Passenger side buckle switch line
    Ignition switch ON, buckle switch ON
    0.12 to 0.18 A
    Ignition switch ON, buckle switch OFF
    0.4 to 0.7 mA
    Y1-1 (SGD1) - Y2-3 (GND)
    G - W-B
    Front occupant detection sensor LH ground line
    Always
    Below 1 Ω
    Y1-2 (SGD2) - Y2-3 (GND)
    O - W-B
    Front occupant detection sensor RH ground line
    Always
    Below 1 Ω
    Y1-3 (SGD3) - Y2-3 (GND)
    W - W-B
    Rear occupant detection sensor LH ground line
    Always
    Below 1 Ω
    Y1-4 (SGD4) - Y2-3 (GND)
    BR - W-B
    Rear occupant detection sensor RH ground line
    Always
    Below 1 Ω
    Y1-11 (SVC1) - Y1-1 (SGD1)
    R - G
    Front occupant detection sensor LH power supply line
    Ignition switch ON, load is applied to front occupant detection sensor LH
    4.5 to 5.1 V
    Y1-12 (SVC2) - Y1-2 (SGD2)
    W - O
    Front occupant detection sensor RH power supply line
    Ignition switch ON, load is applied to front occupant detection sensor RH
    4.5 to 5.1 V
    Y1-5 (SVC3) - Y1-3 (SGD3)
    GR - W
    Rear occupant detection sensor LH power supply line
    Ignition switch ON, load is applied to rear occupant detection sensor LH
    4.5 to 5.1 V
    Y1-6 (SVC4) - Y1-4 (SGD4)
    V - BR
    Rear occupant detection sensor RH power supply line
    Ignition switch ON, load is applied to rear occupant detection sensor RH
    4.5 to 5.1 V
    Y1-7 (SIG1) - Y1-1 (SGD1)
    P - G
    Front occupant detection sensor LH signal line
    Ignition switch ON, load is applied to front occupant detection sensor LH
    Pulse generation
    Y1-8 (SIG2) - Y1-2 (SGD2)
    L - O
    Front occupant detection sensor RH signal line
    Ignition switch ON, load is applied to front occupant detection sensor RH
    Pulse generation
    Y1-9 (SIG3) - Y1-3 (SGD3)
    Y - W
    Rear occupant detection sensor LH signal line
    Ignition switch ON, load is applied to rear occupant detection sensor LH
    Pulse generation
    Y1-10 (SIG4) - Y1-4 (SGD4)
    B - BR
    Rear occupant detection sensor RH signal line
    Ignition switch ON, load is applied to rear occupant detection sensor RH
    Pulse generation