ENGINE OIL COOLER > INSTALLATION |
| 1. INSTALL OIL COOLER ASSEMBLY |
Install a new seal washer to the bolt.
Install the oil cooler with the bolt and nut.
![]() |
Install the 2 hoses.
| *1 | Upward |
| *2 | Rearward |
| 2. INSTALL OIL FILTER BRACKET |
Install the oil filter bracket and a new gasket with the 2 nuts and bolt.
| 3. CONNECT WATER BY-PASS PIPE SUB-ASSEMBLY |
![]() |
Connect the 2 hoses and water by-pass pipe.
| *1 | Upward |
| *2 | Rearward |
Install the 3 bolts.
| 4. INSTALL OIL FILTER ELEMENT |
Clean the inside of the oil filter cap, the threads and O-ring groove.
![]() |
Apply a small amount of engine oil to a new O-ring and install the O-ring to the oil filter cap.
| *1 | O-Ring |
| *a | CORRECT |
| *b | INCORRECT |
Set a new oil filter element on the oil filter cap.
Remove any dirt or foreign matter from the installation surface of the engine.
Apply a small amount of engine oil to the O-ring again and temporarily install the oil filter cap.
![]() |
Using SST, tighten the oil filter cap.
| *1 | Oil Filter Bracket |
| *2 | O-Ring |
| *3 | Oil Filter Cap |
| *4 | Oil Filter Bracket Clip |
| *a | No Gap |
![]() |
Apply a small amount of engine oil to a new drain plug O-ring and install the O-ring to the oil filter cap.
| *1 | O-Ring |
Install the oil filter drain plug.
| 5. ADD ENGINE OIL |
![]() |
Add fresh oil.
| Oil grade | Oil Viscosity (SAE) |
| ILSAC GF-5 multigrade engine oil | 0W-20 |
| Item | Specified Condition |
| Drain and refill without oil filter change | 5.6 liters (5.9 US qts, 4.9 Imp. qts) |
| Drain and refill with oil filter change | 6.1 liters (6.4 US qts, 5.4 Imp. qts) |
| Dry fill | 7.0 liters (7.4 US qts, 6.2 Imp. qts) |
| 6. CHECK ENGINE OIL LEVEL |
Warm up the engine, and then stop the engine and wait for 5 minutes.
Check that the engine oil level is between the low level and full level marks on the dipstick.
If low, check for leakage and add oil up to the full level mark.
| 7. ADD ENGINE COOLANT |
Add engine coolant.
Slowly pour coolant into the radiator reservoir until it reaches the FULL line.
Install the reservoir cap.
Install the radiator cap.*1
Start the engine and stop it immediately.*2
Allow approximately 10 seconds to pass. Then remove the radiator cap and check the coolant level. If the coolant level has decreased, add coolant.*3
Repeat steps *1, *2 and *3 until the coolant level does not decrease.
Install the radiator cap.*4
Set the air conditioning as follows.*5
| Item | Condition |
| Fan speed | Any setting except off |
| Temperature | Toward WARM |
| Air conditioning switch | Off |
Start the engine, warm it up until the thermostat opens, and then continue to run the engine for several minutes to circulate the coolant.*6
Stop the engine, wait until the engine coolant cools down to ambient temperature. Then remove the radiator cap and check the coolant level.*7
If the coolant level has decreased, add coolant and warm up the engine until the thermostat opens.*8
If the coolant level has not decreased, check that the coolant level in the radiator reservoir is at the FULL line.
If the coolant level is below the FULL line, repeat steps *4 through *8.
If the coolant level is above the FULL line, drain coolant until the coolant level reaches the FULL line.
| 8. INSPECT FOR ENGINE OIL LEAK |
Start the engine. Make sure that there are no oil leaks from the area that was worked on.
| 9. INSPECT FOR COOLANT LEAK |
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.