SFI SYSTEM > ECM Power Source Circuit |

| 1.CHECK HARNESS AND CONNECTOR (BATTERY - NO. 1 INTEGRATION RELAY) |
![]() |
Remove the No. 1 integration relay from the engine room junction block.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1C-1 - Body ground | Always | 11 to 14 V |
| *a | Front view of wire harness connector (to No. 1 Integration Relay) |
|
| ||||
| OK | |
| 2.INSPECT NO. 1 INTEGRATION RELAY (EFI) |
Inspect the No. 1 integration relay (EFI) .
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (+B, +B2 AND MREL CIRCUIT) |
Check the harness and connectors between the No. 1 integration relay and ECM.
Remove the No. 1 integration relay from the engine room junction block.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A24-34 (MREL) - 1B-2 | Always | Below 1 Ω |
| A24-3 (+B) - 1B-4 | Always | Below 1 Ω |
| A24-2 (+B2) - 1B-4 | Always | Below 1 Ω |
| A24-34 (MREL) or 1B-2 - Body ground | Always | 10 kΩ or higher |
| A24-3 (+B) or 1B-4 - Body ground | Always | 10 kΩ or higher |
| A24-2 (+B2) or 1B-4 - Body ground | Always | 10 kΩ or higher |
Check the harness and connectors between the No. 1 integration relay and body ground.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1B-3 - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND) |
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D74-81 (E1) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 5.INSPECT ECM (IGSW VOLTAGE) |
![]() |
Disconnect the ECM connectors.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A24-28 (IGSW) - D74-81 (E1) | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector (to ECM) |
|
| ||||
| OK | ||
| ||
| 6.INSPECT NO. 1 INTEGRATION RELAY (IG2) |
Inspect the No. 1 integration relay (IG2) .
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM, NO. 1 INTEGRATION RELAY - BODY GROUND) |
Remove the No. 1 integration relay from the engine room junction block.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1B-8 - A24-28 (IGSW) | Always | Below 1 Ω |
| 1B-8 or A24-28 (IGSW) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - IGNITION SWITCH ASSEMBLY) |
Check the harness and connectors between the No. 1 integration relay and ignition switch assembly.
Remove the No. 1 integration relay from the engine room junction block.
Disconnect the ignition switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1B-6 - J9-6 (IG2) | Always | Below 1 Ω |
| 1B-6 or J9-6 (IG2) - Body ground | Always | 10 kΩ or higher |
Check the harness and connectors between the No. 1 integration relay and body ground.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1B-7 - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 9.INSPECT IGNITION SWITCH ASSEMBLY |
Inspect the ignition switch assembly (Click here).
|
| ||||
| OK | ||
| ||