PARKING BRAKE ASSEMBLY > REASSEMBLY |
| 1. INSTALL PARKING BRAKE ANCHOR BLOCK |
![]() |
Install the anchor block with the 2 nuts.
| 2. CONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY |
![]() |
Connect the No. 3 parking brake cable with the bolt.
| 3. INSTALL PARKING BRAKE SHOE LEVER LH |
Apply high temperature grease to the parking brake shoe lever.
![]() ![]() |
Install the parking brake shoe lever to the No. 3 parking brake cable.
| 4. INSTALL NO. 2 PARKING BRAKE SHOE ASSEMBLY LH |
Apply high temperature grease to the areas of the backing plate that contact the shoe.
![]() |
Using SST, install the No. 2 parking brake shoe with the shoe hold down spring pin, compression spring and shoe hold down spring cup.
| 5. INSTALL NO. 1 PARKING BRAKE SHOE ASSEMBLY LH |
Apply high temperature grease to the areas of the backing plate that contact the shoe.
![]() |
Apply the high temperature grease to the areas of the shoe adjusting screw set shown in the illustration.
Set the parking brake shoe and shoe adjuster screw set in place.
Connect the tension spring.
![]() |
Using SST, install the No. 1 parking brake shoe with the shoe hold down spring pin, compression spring and shoe hold down spring cup.
| 6. INSTALL PARKING BRAKE SHOE RETURN SPRING |
![]() |
Using SST, install the shoe return spring.
| 7. CHECK PARKING BRAKE INSTALLATION |
Check that each part is installed properly.

| 8. INSTALL REAR DISC |
![]() |
Align the matchmarks and install the rear disc.
| 9. CONNECT REAR DISC BRAKE CYLINDER ASSEMBLY LH |
![]() |
Connect the rear disc brake cylinder with 2 new bolts.
| 10. ADJUST PARKING BRAKE SHOE CLEARANCE |
Temporarily install the hub nuts.
Remove the hole plug.
![]() |
Insert a screwdriver into the adjustment hole of the disc. Rotate the adjustment wheel in the "X" direction until the shoes are locked. Then rotate the adjustment wheel in the "Y" direction 8 notches.
Check that the disc can be rotated smoothly. If not, rotate the adjustment wheel in the "Y" direction and check again.
Install the hole plug.
Remove the hub nuts.
| 11. CHECK PARKING BRAKE PEDAL TRAVEL |
Firmly depress the parking brake pedal.
Release the parking brake.
Slowly depress the parking brake pedal with a force of approximately 300 N (31 kgf, 67.4 lbf) and count the number of clicks.
| 12. ADJUST PARKING BRAKE PEDAL TRAVEL |
Depress the parking brake pedal.
![]() |
Apply load equivalent to 4 kN (408 kgf, 899.2 lbf) on equalizer twice to pull No. 2 and No. 3 parking brake cable to remove initial elongation.
Release the parking brake pedal to the original position.
![]() |
Loosen the pedal side No. 1 parking brake cable lock nut.
Turn the pedal side No. 1 parking brake cable adjustment nut until the parking brake pedal travel is correct.
| Pedal Load | Specified Condition |
| 300 N (31 kgf, 67.4 lbf) | 6 to 9 clicks |
Using a wrench or equivalent to hold the adjustment nut, tighten the lock nut.
Additionally, excessive pedal travel can be adjusted on the No. 1 parking brake cable underbody side as follows.
Release the parking brake pedal to the original position.
![]() |
Loosen the underbody side No. 1 parking brake cable lock nut.
Turn the underbody side No. 1 parking brake cable adjustment nut until the parking brake pedal travel is correct.
| Pedal Load | Specified Condition |
| 300 N (31 kgf, 67.4 lbf) | 6 to 9 clicks |
Tighten the No. 1 parking brake cable underbody lock nut.
Depress and release the parking brake pedal 3 or 4 times. Then check the number of clicks when depressing the pedal.
Check whether the parking brake drags or not.
If the parking brake drags, adjust the shoe clearance.
When operating the parking brake pedal, check that the parking brake pedal indicator light comes on at the first notch.
If not, adjust the parking brake switch installation position.
| 13. INSTALL REAR WHEEL LH |
| 14. SETTLE PARKING BRAKE SHOE AND DISC |
Drive the vehicle for approximately 400 m (0.25 miles) under the following conditions.
The vehicle speed is approximately 50 km/h (31 mph) and the vehicle is on a safe, level and dry road.
The parking brake pedal is being depressed with a force of 150 N (15 kgf, 33.7 lbf).
Repeat the procedures above 2 or 3 times.