Home › BODY ELECTRICAL › PARK ASSIST / MONITORING › ULTRASONIC SENSOR (for Rear Side)

ULTRASONIC SENSOR (for Rear Side) > INSTALLATION

for Preparation Click here


CAUTION:
As the rear bumper cover is extremely heavy, the engine lifter may suddenly drop if the instructions listed in the repair manual are not followed. Therefore, always follow the instructions listed in the repair manual when performing this procedure.



1. INSTALL NO. 2 ULTRASONIC SENSOR (for Steel Type Bumper)


    B354821
  1. Install the No. 2 ultrasonic sensor as shown in the illustration.

    NOTICE:
    Do not damage the bumper with the protrusion when installing the No. 2 ultrasonic sensor.



2. INSTALL NO. 2 ULTRASONIC SENSOR RETAINER (for Steel Type Bumper)


    B354820
  1. Install the No. 2 ultrasonic sensor retainer as shown in the illustration.



3. INSTALL NO. 2 ULTRASONIC SENSOR (for Resin Type Bumper)



B354822E01

  1. Attach the 4 claws to install the No. 2 ultrasonic sensor as shown in the illustration.
    Text in Illustration 
    *a
    No. 2 ultrasonic sensor direction
    *b
    Keyhole direction

    NOTICE:
    1. No. 2 ultrasonic sensor direction is the same as the keyhole direction.
    1. Do not damage the bumper with the protrusion when installing the No. 2 ultrasonic sensor.



4. INSTALL NO. 3 ULTRASONIC SENSOR



B354822E01

  1. Attach the 4 claws to install the No. 3 ultrasonic sensor as shown in the illustration.
    Text in Illustration 
    *a
    No. 3 ultrasonic sensor direction
    *b
    Keyhole direction

    NOTICE:
    1. No. 3 ultrasonic sensor direction is the same as the keyhole direction.
    1. Do not damage the bumper with the protrusion when installing the No. 3 ultrasonic sensor.



5. INSTALL NO. 2 FRAME WIRE (for Steel Type Bumper)
  1. w/ Towing Package:
    .

  1. w/o Towing Package:
    (See page ).



6. INSTALL REAR BUMPER BAR CORNER REINFORCEMENT LH (for Steel Type Bumper)
  1. Install the rear bumper bar corner reinforcement LH with the 5 bolts.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }



7. INSTALL REAR BUMPER BAR CORNER REINFORCEMENT RH (for Steel Type Bumper)

HINT:
Use the same procedure described for the LH side.



8. INSTALL REAR BUMPER EXTENSION INSERT LH (for Resin Type Bumper)
  1. Install the rear bumper extension insert LH with the 8 clips.



9. INSTALL REAR BUMPER EXTENSION INSERT RH (for Resin Type Bumper)

HINT:
Use the same procedure described for the LH side.



10. INSTALL LICENSE PLATE LIGHT ASSEMBLY LH
  1. Connect the connector.

  1. Attach the 2 claws to install the license plate assembly LH.



11. INSTALL LICENSE PLATE LIGHT ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.



12. INSTALL REAR BUMPER PAD SUB-ASSEMBLY (for Steel Type Bumper)
  1. Attach the 12 claws and 2 guides to install the rear bumper pad sub-assembly LH.

  1. Install the 3 clips.



13. INSTALL REAR BUMPER PAD SUB-ASSEMBLY (for Resin Type Bumper)
  1. Attach the 12 claws and 2 guides to install the rear bumper pad sub-assembly LH.

  1. Install the 3 clips.



14. INSTALL REAR BUMPER PLATE LH (for Steel Type Bumper)
  1. Attach the 3 claws and clip to install the rear bumper plate LH.



15. INSTALL REAR BUMPER PLATE LH (for Resin Type Bumper)
  1. Attach the 3 claws and clip to install the rear bumper plate LH.



16. INSTALL REAR BUMPER PLATE RH (for Steel Type Bumper)

HINT:
Use the same procedure described for the LH side.



17. INSTALL REAR BUMPER PLATE RH (for Resin Type Bumper)

HINT:
Use the same procedure described for the LH side.



18. INSTALL REAR BUMPER COVER (for Steel Type Bumper)
  1. w/ Towing Package:

    1. Using an engine lifter or equivalent, install the rear bumper cover with the 12 bolts.

      Torque:
      153 N*m{ 1560 kgf*cm , 113 ft.*lbf }

      NOTICE:
      1. Using plate lift attachments or equivalent, set the rear bumper cover on a flat surface.
      2. Be sure to perform the operation with 2 persons or more.
      3. Be careful not to damage the rear bumper cover.

  1. w/o Towing Package:

    1. Using an engine lifter or equivalent, install the rear bumper cover with the 8 bolts.

      Torque:
      153 N*m{ 1560 kgf*cm , 113 ft.*lbf }

      NOTICE:
      1. Using plate lift attachments or equivalent, set the rear bumper cover on a flat surface.
      2. Be sure to perform the operation with 2 persons or more.
      3. Be careful not to damage the rear bumper cover.



19. INSTALL REAR BUMPER COVER (for Resin Type Bumper)
  1. w/ Towing Package:

    1. Using an engine lifter or equivalent, install the rear bumper cover with the 12 bolts.

      Torque:
      153 N*m{ 1560 kgf*cm , 113 ft.*lbf }

      NOTICE:
      1. Using plate lift attachments or equivalent, set the rear bumper cover on a flat surface.
      2. Be sure to perform the operation with 2 persons or more.
      3. Be careful not to damage the rear bumper cover.

  1. w/o Towing Package:

    1. Using an engine lifter or equivalent, install the rear bumper cover with the 8 bolts.

      Torque:
      153 N*m{ 1560 kgf*cm , 113 ft.*lbf }

      NOTICE:
      1. Using plate lift attachments or equivalent, set the rear bumper cover on a flat surface.
      2. Be sure to perform the operation with 2 persons or more.
      3. Be careful not to damage the rear bumper cover.



20. INSTALL WIRING HARNESS CONNECTOR (for Steel Type Bumper)
  1. Attach the 2 claws to install the wiring harness connector.

  1. Connect the connector.



21. INSTALL WIRING HARNESS CONNECTOR (for Resin Type Bumper)
  1. Attach the 2 claws to install the wiring harness connector.

  1. Connect the connector.



22. INSTALL CONNECTOR COVER (for Steel Type Bumper)

HINT:
Use the same procedure described for the wiring harness connector.



23. INSTALL CONNECTOR COVER (for Resin Type Bumper)

HINT:
Use the same procedure described for the wiring harness connector.