Home › BODY ELECTRICAL › NAVIGATION › NAVIGATION SYSTEM

NAVIGATION SYSTEM > Sound Signal Circuit between Navigation Receiver Assembly and Stereo Component Amplifier

for Preparation Click here


DESCRIPTION

The navigation receiver assembly sends a sound signal to the stereo component amplifier assembly via this circuit.
The sound signal that has been sent is amplified by the stereo component amplifier assembly, and then is sent to the speakers.

WIRING DIAGRAM


E282412E01


E282606E01


INSPECTION PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
  1. for 7 or 9 Speakers:

    1. Disconnect the J134 and J133 navigation receiver assembly connectors.

    2. Disconnect the J145 stereo component amplifier assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      J133-2 (FL+) - J145-1 (FL+)
      Always
      Below 1 Ω
      J133-6 (FL-) - J145-6 (FL-)
      Always
      Below 1 Ω
      J133-1 (FR+) - J145-2 (FR+)
      Always
      Below 1 Ω
      J133-5 (FR-) - J145-7 (FR-)
      Always
      Below 1 Ω
      J134-2 (RL+) - J145-3 (RL+)
      Always
      Below 1 Ω
      J134-6 (RL-) - J145-8 (RL-)
      Always
      Below 1 Ω
      J134-1 (RR+) - J145-9 (RR+)
      Always
      Below 1 Ω
      J134-3 (RR-) - J145-10 (RR-)
      Always
      Below 1 Ω
      J133-2 (FL+) - Body ground
      Always
      10 kΩ or higher
      J133-6 (FL-) - Body ground
      Always
      10 kΩ or higher
      J133-1 (FR+) - Body ground
      Always
      10 kΩ or higher
      J133-5 (FR-) - Body ground
      Always
      10 kΩ or higher
      J134-2 (RL+) - Body ground
      Always
      10 kΩ or higher
      J134-6 (RL-) - Body ground
      Always
      10 kΩ or higher
      J134-1 (RR+) - Body ground
      Always
      10 kΩ or higher
      J134-3 (RR-) - Body ground
      Always
      10 kΩ or higher

  1. for 12 Speakers:

    1. Disconnect the J134 and J133 navigation receiver assembly connectors.

    2. Disconnect the J141 stereo component amplifier assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      J133-6 (FL-) - J141-2 (L-)
      Always
      Below 1 Ω
      J133-2 (FL+) - J141-3 (L+)
      Always
      Below 1 Ω
      J133-5 (FR-) - J141-4 (R-)
      Always
      Below 1 Ω
      J133-1 (FR+) - J141-5 (R+)
      Always
      Below 1 Ω
      J133-6 (FL-) - Body ground
      Always
      10 kΩ or higher
      J133-2 (FL+) - Body ground
      Always
      10 kΩ or higher
      J133-5 (FR-) - Body ground
      Always
      10 kΩ or higher
      J133-1 (FR+) - Body ground
      Always
      10 kΩ or higher
      J134-4 (SLD2) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)