REAR AXLE SHAFT > INSTALLATION |
| 1. INSTALL REAR AXLE SHAFT OIL SEAL |
![]() |
Using SST and a hammer, tap in a new oil seal.
Apply MP grease to the lip of the oil seal.
| 2. INSTALL REAR AXLE SHAFT |
Apply MP grease to a new O-ring.
Install the O-ring to the axle shaft.
![]() |
Install the rear axle shaft and parking brake plate with the 4 nuts.
| 3. CONNECT REAR SPEED SENSOR LH |
![]() |
Install the speed sensor (labeled A) with the nut (labeled B).
Connect the speed sensor connector (labeled C).
| 4. CONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY |
![]() |
Connect the No. 3 parking brake cable with the bolt.
| 5. INSTALL PARKING BRAKE SHOE LEVER SUB-ASSEMBLY LH |
Apply high temperature grease to the parking brake shoe lever.
![]() ![]() |
Install the parking brake shoe lever to the No. 3 parking brake cable.
| 6. INSTALL NO. 2 PARKING BRAKE SHOE ASSEMBLY LH |
Apply high temperature grease to the areas of the backing plate that contact the shoe.
![]() |
Using SST, install the No. 2 parking brake shoe with the shoe hold down spring pin, compression spring and shoe hold down spring cup.
| 7. INSTALL NO. 1 PARKING BRAKE SHOE ASSEMBLY LH |
Apply high temperature grease to the areas of the backing plate that contact the shoe.
![]() |
Apply the high temperature grease to the areas of the shoe adjusting screw set shown in the illustration.
Set the parking brake shoe and shoe adjuster screw set in place.
Connect the tension spring.
![]() |
Using SST, install the No. 1 parking brake shoe with the shoe hold down spring pin, compression spring and shoe hold down spring cup.
| 8. INSTALL PARKING BRAKE SHOE RETURN TENSION SPRING LH |
![]() |
Using SST, install the shoe return spring.
| 9. CHECK PARKING BRAKE INSTALLATION |
Check that each part is installed properly.

| 10. INSTALL REAR DISC LH |
![]() |
Align the matchmarks and install the rear disc.
| 11. ADJUST PARKING BRAKE SHOE CLEARANCE |
Temporarily install the hub nuts.
Remove the hole plug.
![]() |
Insert a screwdriver into the adjustment hole of the disc. Rotate the adjustment wheel in the "X" direction until the shoes are locked. Then rotate the adjustment wheel in the "Y" direction 8 notches.
Check that the disc can be rotated smoothly. If not, rotate the adjustment wheel in the "Y" direction and check again.
Install the hole plug.
Remove the hub nuts.
| 12. CONNECT REAR DISC BRAKE CYLINDER ASSEMBLY LH |
![]() |
Connect the rear disc brake cylinder and install 2 new bolts.
| 13. CONNECT REAR BRAKE FLEXIBLE HOSE |
Set the flexible hose to the connecting point with the brake tube, and then install a new clip.
![]() |
Using union nut wrench, connect the flexible hose to the brake tube while holding the flexible hose with a wrench.
| 14. FILL RESERVOIR WITH BRAKE FLUID |
Fill the brake fluid (Click here).
| 15. BLEED BRAKE LINE |
Bleed brake line
Remove the brake master cylinder reservoir filler cap assembly.
Add brake fluid into the reservoir between MAX and MIN level on the brake fluid reservoir.
Connect a vinyl tube to the bleeder plug of the front disc brake cylinder RH.
Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed.*1
When fluid stops coming out, tighten the bleeder plug, and then release the brake pedal.*2
Repeat *1 and *2 until all the air in the brake fluid is completely bled out and the new brake fluid comes out.
Tighten the bleeder plug completely.
Replace the brake fluid from the front disc brake cylinder LH using the same procedure as for RH.
Connect a vinyl tube to the bleeder plug of the rear disc brake cylinder RH.
Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed.*1
When fluid stops coming out, tighten the bleeder plug, and then release the brake pedal.*2
Repeat *1 and *2 until all the air in the brake fluid is completely bled out and the new brake fluid comes out.
Tighten the bleeder plug completely.
Replace the brake fluid from the rear disc brake cylinder LH using the same procedure as for RH.
Check and bleed brake system.
If the following malfunction symptoms occur, air may have entered the brake fluid line. Perform the following air bleed procedures.
Check and adjust brake fluid level in reservoir .
| 16. CHECK BRAKE FLUID LEVEL IN RESERVOIR |
![]() |
Check the fluid level and add fluid if necessary.
| 17. CHECK FOR BRAKE FLUID LEAKS |
| 18. INSTALL REAR WHEEL LH |
| 19. INSPECT DIFFERENTIAL OIL |
![]() |
Add differential oil so that the oil level is between 0 to 5 mm (0 to 0.197 in.) from the bottom lip of the differential filler plug hole.
| Item | Oil type and viscosity |
| Front differential | Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent. |
| Rear differential |
| Specified Condition | |
| 2.00 to 2.10 liters (2.12 to 2.21 US qts., 1.76 to 1.84 Imp. qts.) |
| Engine type | Wheelbase type | Cab type | Drive type | Specified Condition |
| 3UR-FE. 3UR-FBE | 3220 mm (10 ft. 6.8 in.) | Regular | 2WD | 3.45 to 3.55 liters (3.65 to 3.75 US qts., 3.04 to 3.12 Imp. qts.) |
| 4WD | ||||
| 3700 mm (12 ft. 1.7 in.) | Regular | 2WD | 3.55 to 3.65 liters (3.76 to 3.85 US qts., 3.13 to 3.21 Imp. qts.) | |
| 4WD | ||||
| Double | 2WD | |||
| 4WD | ||||
| CrewMax | 2WD | 3.70 to 3.80 liters (3.91 to 4.01 US qts., 3.26 to 3.34 Imp. qts.) | ||
| 4WD | 3.55 to 3.65 liters (3.76 to 3.85 US qts., 3.13 to 3.21 Imp. qts.) | |||
| 4180 mm (13 ft. 8.6 in.) | Double | 2WD | 3.70 to 3.80 liters (3.91 to 4.01 US qts., 3.26 to 3.34 Imp. qts.) | |
| 4WD | ||||
| 1GR-FE and 1UR-FE | 3220 mm (10 ft. 6.8 in.) | Regular | 2WD | 4.00 to 4.10 liters (4.23 to 4.33 US qts., 3.52 to 3.60 Imp. qts.) |
| 4WD | ||||
| 3700 mm (12 ft. 1.7 in.) | ALL | 2WD | 4.55 to 4.65 liters (4.81 to 4.91 US qts., 4.01 to 4.09 Imp. qts.) | |
| 4WD | ||||
| 4180 mm (13 ft. 8.6 in.) | 2WD | |||
| 4WD |
for Rear Differential:
Install a new gasket and the filler plug.
for Front Differential:
Using a 10 mm hexagon wrench, install a new gasket and the filler plug.
| 20. INSPECT FOR DIFFERENTIAL OIL LEAK |
| 21. CHECK PARKING BRAKE PEDAL TRAVEL |
Firmly depress the parking brake pedal.
Release the parking brake.
Slowly depress the parking brake pedal with a force of approximately 300 N (31 kgf, 67.4 lbf) and count the number of clicks.
| 22. ADJUST PARKING BRAKE PEDAL TRAVEL |
Depress the parking brake pedal.
![]() |
Apply load equivalent to 4 kN (408 kgf, 899.2 lbf) on equalizer twice to pull No. 2 and No. 3 parking brake cable to remove initial elongation.
Release the parking brake pedal to the original position.
![]() |
Loosen the pedal side No. 1 parking brake cable lock nut.
Turn the pedal side No. 1 parking brake cable adjustment nut until the parking brake pedal travel is correct.
| Pedal Load | Specified Condition |
| 300 N (31 kgf, 67.4 lbf) | 6 to 9 clicks |
Using a wrench or equivalent to hold the adjustment nut, tighten the lock nut.
Additionally, excessive pedal travel can be adjusted on the No. 1 parking brake cable underbody side as follows.
Release the parking brake pedal to the original position.
![]() |
Loosen the underbody side No. 1 parking brake cable lock nut.
Turn the underbody side No. 1 parking brake cable adjustment nut until the parking brake pedal travel is correct.
| Pedal Load | Specified Condition |
| 300 N (31 kgf, 67.4 lbf) | 6 to 9 clicks |
Tighten the No. 1 parking brake cable underbody lock nut.
Depress and release the parking brake pedal 3 or 4 times. Then check the number of clicks when depressing the pedal.
Check whether the parking brake drags or not.
If the parking brake drags, adjust the shoe clearance.
When operating the parking brake pedal, check that the parking brake pedal indicator light comes on at the first notch.
If not, adjust the parking brake switch installation position.
| 23. CHECK SRS WARNING LIGHT |
Check the SRS warning light (Click here).
| 24. CHECK SPEED SENSOR SIGNAL |
Check the speed sensor signal .