Home › ENGINE ยท 1GR-FE › ENGINE MECHANICAL › ENGINE UNIT

ENGINE UNIT > DISASSEMBLY

for Preparation Click here



1. REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY


    A222098
  1. Disconnect the oil pressure switch connector from the engine oil pressure switch assembly.

  1. Using a 24 mm deep socket wrench, remove the engine oil pressure switch assembly.



2. REMOVE ENGINE COOLANT TEMPERATURE SENSOR


A224780
  1. Disconnect the sensor connector.

  1. Using a 19 mm deep socket wrench, remove the sensor.

  1. Remove the gasket from the sensor.



3. REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY


    A273790
  1. Remove the water drain cock plug from the water drain cock.

  1. Remove the water drain cock from the cylinder block.



4. REMOVE VVT SENSOR


    A224729
  1. LH:
    Remove the 2 bolts and 2 VVT sensors.



    A224728
  1. RH:
    Remove the 2 bolts and 2 VVT sensors.



5. REMOVE CRANKSHAFT POSITION SENSOR


    A224727
  1. Remove the bolt and crankshaft position sensor.



6. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY RH


    A224731
  1. LH:
    Remove the 2 bolts and 2 oil control valves.



    A224730
  1. RH:
    Remove the 2 bolts and 2 oil control valves.



7. REMOVE OIL FILLER CAP HOUSING


    A221161
  1. Remove the oil filler cap.

  1. Remove the 2 nuts, oil filler cap housing and gasket.



8. REMOVE NO. 1 OIL PIPE


    A223691
  1. Remove the 2 oil pipe unions, oil control valve filter LH, 3 gaskets and No. 1 oil pipe.

    NOTICE:
    Do not touch the mesh when removing the oil control valve filter.



9. REMOVE NO. 2 OIL PIPE


    A223692
  1. Remove the 2 oil pipe unions, oil control valve filter RH, 3 gaskets and No. 2 oil pipe.

    NOTICE:
    Do not touch the mesh when removing the oil control valve filter.



10. REMOVE OIL FILTER ELEMENT


    A094910E09
  1. Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.
    Text in Illustration 
    *1
    Pipe
    *2
    Hose



    A222100
  1. Remove the oil filter drain plug.



    A222101E01
  1. Install the pipe to the oil filter cap.
    Text in Illustration 
    *1
    Cap
    *2
    Valve
    *3
    Pipe
    *4
    O-Ring
    *5
    Hose

    NOTICE:
    If the O-ring is removed with the oil filter drain plug, install the O-ring together with the pipe.

    HINT:
    Use a container to catch the draining oil.



    A222102
  1. Check that oil is drained from the oil filter. Then, disconnect the pipe as shown in the illustration and remove the O-ring.



    A222103E01
  1. Using SST, remove the oil filter cap.

    SST
    09228-06501  
    Text in Illustration 
    *1
    Oil Filter Bracket Clip

    NOTICE:
    Do not remove the oil filter bracket clip.



    A153538E03
  1. Remove the oil filter element and O-ring from the oil filter cap.
    Text in Illustration 
    *1
    O-Ring

    NOTICE:
    Be sure to remove the O-ring (for the oil filter cap) by hand, without using any tools, to prevent damage to the groove for the O-ring in the oil filter cap.



11. REMOVE OIL FILTER BRACKET


    A225410
  1. Remove the 2 nuts, bolt, oil filter bracket and gasket.



12. REMOVE WATER INLET HOUSING


    A225380
  1. Disconnect the 3 water by-pass hoses.



    A223012
  1. Remove the 5 bolts and water inlet housing.



    A224736
  1. Remove the O-ring and gasket from the water outlet pipe and water pump.



    A225379
  1. Remove the 3 water by-pass hoses.



13. REMOVE REAR WATER BY-PASS JOINT


    A076534E01
  1. Remove the 2 bolts, 4 nuts, rear water by-pass joint and 2 gaskets.

  1. Remove the O-ring from the No. 1 water outlet pipe.



14. REMOVE SPARK PLUG
  1. Remove the 6 spark plugs.



15. REMOVE PCV VALVE SUB-ASSEMBLY


    A237918
  1. Loosen the hose clamp and disconnect the PCV hose from the valve.



    A237919
  1. Remove the valve.



16. REMOVE CRANKSHAFT PULLEY


    A072947E04
  1. Using SST, hold the crankshaft pulley and loosen the pulley bolt. Continue to loosen the bolt until only 2 or 3 threads are screwed into the crankshaft.

    SST
    09213-54015   (91651-60855)
    09330-00021  



    A072948E02
  1. Using the pulley set bolt and SST, remove the crankshaft pulley and pulley bolt.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05031)



17. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH


    A226542
  1. Remove the 12 bolts, seal washer, cylinder head cover and gasket.

    HINT:
    Make sure the removed parts are returned to the same places they were removed from.



    A223665
  1. Remove the 3 gaskets.



18. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY


    A226543
  1. Remove the 12 bolts, seal washer, cylinder head cover and gasket.

    HINT:
    Make sure the removed parts are returned to the same places they were removed from.



    A221164
  1. Remove the 3 gaskets.



19. REMOVE SPARK PLUG TUBE GASKET


A124195
  1. Bend the ventilation baffle plate claws on the cylinder head cover to an angle of 90° or more.
    Text in Illustration 
    V100135
    Pry

  1. Remove the 6 spark plug tube gaskets.

    HINT:
    Be careful not to damage the gasket when removing it as the removed gasket needs to be used when installing a new one.



20. REMOVE OIL PAN DRAIN PLUG
  1. Remove the drain plug and gasket.



21. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY


    A174340
  1. Remove the 10 bolts and 2 nuts.

    HINT:
    Make sure the removed parts are returned to the same places they were removed from.



    A174341E02
  1. Insert the blade of an oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan.
    Text in Illustration 
    *1
    Oil Pan Seal Cutter

    NOTICE:
    Be careful not to damage the contact surfaces of the oil pans.



22. REMOVE OIL STRAINER SUB-ASSEMBLY


    A239204
  1. Remove the 2 nuts, oil strainer and gasket.



23. REMOVE OIL PAN SUB-ASSEMBLY


    A222173
  1. Remove the 17 bolts and 2 nuts.

    HINT:
    Make sure the removed parts are returned to the same places they were removed from.



    A221168E04
  1. Using a screwdriver, remove the oil pan by prying between the oil pan and cylinder block as shown in the illustration.
    Text in Illustration 
    *A
    LH Side
    *B
    RH Side
    *a
    Pry

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder block and oil pan.

    HINT:
    Tape the screwdriver tip before use.



    A222122
  1. Remove the 3 O-rings from the timing chain cover.



24. REMOVE NO. 1 OIL PAN BAFFLE PLATE


    A224779
  1. Remove the 6 bolts and No. 1 oil pan baffle plate.



25. REMOVE ENGINE REAR OIL SEAL RETAINER


    A076247E04
  1. Remove the 5 bolts and 2 nuts.

  1. Using a screwdriver, remove the oil seal retainer by prying between the oil seal retainer and crankshaft bearing cap.
    Text in Illustration 
    *a
    Pry

    HINT:
    Tape the screwdriver tip before use.



26. REMOVE REAR CRANKSHAFT OIL SEAL


    A076248E03
  1. Using a screwdriver and hammer, tap out the oil seal.

    NOTICE:
    Be careful not to damage the rear oil seal retainer.



27. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY


    A221169
  1. Remove the 26 bolts and the 2 nuts.



    A221170
  1. Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver.

    NOTICE:
    Be careful not to damage the contact surfaces of the timing chain cover, cylinder block and cylinder head.

    HINT:
    Tape the screwdriver tip before use.



    A221404
  1. Remove the oil pump gasket from the cylinder block.



28. REMOVE WATER PUMP ASSEMBLY


    A221171
  1. Remove the 8 bolts, water pump and gasket.



29. REMOVE FRONT CRANKSHAFT OIL SEAL
  1. Using a screwdriver and wooden block, pry out the oil seal.

    NOTICE:
    Do not damage the surface of the oil seal press fit hole.

    HINT:
    Tape the screwdriver tip before use.



30. SET NO. 1 CYLINDER TO TDC/COMPRESSION
  1. Temporarily install the pulley set bolt.



    A222172E01
  1. Turn the crankshaft clockwise to align the timing mark on the crank angle sensor plate with the RH block bore center line (TDC/compression).
    Text in Illustration 
    *1
    Center Line
    *2
    Timing Mark
    *3
    Sensor Plate



    A225378E01
  1. Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing caps as shown in the illustration.
    If not, turn the crankshaft clockwise 1 revolution (360°) and align the timing marks as above.
    Text in Illustration 
    *1
    Timing Mark



31. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY


    A124589E05
  1. Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.
    Text in Illustration 
    *1
    Plunger
    *2
    Stopper Plate
    *3
    Pin

  1. Move the stopper plate downward to set the lock, and insert a pin of 1.27 mm (0.0500 in.) into the stopper plate hole.



    A095165E02
  1. Remove the 2 bolts and No. 1 chain tensioner assembly.



32. REMOVE CHAIN TENSIONER SLIPPER


    A223730
  1. Remove the chain tensioner slipper.



33. REMOVE NO. 1 CHAIN SUB-ASSEMBLY


    A221173E01
  1. Turn the crankshaft counterclockwise 10° to loosen the chain of the crankshaft timing sprocket.
    Text in Illustration 
    *1
    Center Line
    *2
    Timing Mark
    *3
    Sensor Plate

  1. Remove the pulley set bolt.



    A221174
  1. Remove the chain sub-assembly from the crankshaft timing sprocket and place it on the crankshaft.



    A095682E12
  1. Turn the camshaft timing gear assembly on bank 1 clockwise approximately 60° so that it is as shown in the illustration. Be sure to loosen the chain sub-assembly between the banks.

  1. Remove the chain sub-assembly.
    Text in Illustration 
    *A
    for Bank 1



34. REMOVE NO. 1 IDLE GEAR SHAFT


    A221175
  1. Using a 10 mm hexagon wrench, remove the No. 2 idle gear shaft, No. 1 idle gear and No. 1 idle gear shaft.



35. REMOVE NO. 1 CHAIN VIBRATION DAMPER


    A223642
  1. Remove the 2 bolts and No. 1 chain vibration damper.



36. REMOVE NO. 2 CHAIN VIBRATION DAMPER


    A221176
  1. Remove the 2 No. 2 chain vibration dampers.



37. REMOVE CRANKSHAFT TIMING SPROCKET


    A158530E01
  1. Remove the crankshaft timing sprocket.



38. REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 1)


    A221132E01
  1. While raising the No. 2 chain tensioner assembly, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the hole to hold the No. 2 chain tensioner assembly.
    Text in Illustration 
    *1
    Pin
    *2
    Plunger
    *a
    Push



    A221177E01
  1. Using SST to hold the hexagonal portion of each camshaft, loosen the bolts of the camshaft timing gear assembly and camshaft timing exhaust gear assembly.

    SST
    09922-10010  
    Text in Illustration 
    *a
    Turn
    *b
    Hold

    NOTICE:
    Do not loosen the other 4 bolts. If any of the 4 bolts is loosened, replace the camshaft timing gear assembly and/or camshaft timing exhaust gear assembly with a new one.

  1. Remove the 2 bolts and camshaft timing gear assembly together with the No. 2 chain.



39. REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY


    A221178
  1. Remove the bolt and No. 2 chain tensioner assembly.



40. REMOVE CAMSHAFT BEARING CAP (for Bank 1)


    A129700E06
  1. Check that the camshafts are positioned as shown in the illustration.
    Text in Illustration 
    *1
    Knock Pin
    *a
    Front View



    A221179E01
  1. Uniformly loosen and remove the 8 bearing cap bolts in several steps in the sequence shown in the illustration.



    A221180E01
  1. Uniformly loosen and remove the 12 bearing cap bolts in several steps in the sequence shown in the illustration.

    NOTICE:
    Uniformly loosen the bolts while keeping the camshaft level.

  1. Remove the 5 camshaft bearing caps.

  1. Remove the camshaft and No. 2 camshaft.



41. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY RH


    A221181E01
  1. Remove the camshaft housing sub-assembly RH by prying between the cylinder head and camshaft housing sub-assembly RH with a screwdriver.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head and camshaft housing sub-assembly RH.



42. REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 2)


    A221182E01
  1. While pushing down the No. 3 chain tensioner assembly, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the hole to hold the No. 3 chain tensioner assembly.
    Text in Illustration 
    *1
    Pin
    *2
    Plunger
    *a
    Push



    A223637E01
  1. Using SST to hold the hexagonal portion of each camshaft, loosen the bolts of the camshaft timing gear assembly and camshaft timing exhaust gear assembly.

    SST
    09922-10010  
    Text in Illustration 
    *a
    Turn
    *b
    Hold

    NOTICE:
    Do not loosen the other 4 bolts. If any of the 4 bolts is loosened, replace the camshaft timing gear assembly and/or camshaft timing exhaust gear assembly with a new one.

  1. Remove the 2 bolts and camshaft timing gear together with the No. 2 chain.



43. REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY


    A221183
  1. Remove the bolt and No. 3 chain tensioner assembly.



44. REMOVE CAMSHAFT BEARING CAP (for Bank 2)


    A223636E01
  1. Check that the camshafts are positioned as shown in the illustration.
    Text in Illustration 
    *1
    Knock Pin
    *a
    Front View



    A221184E01
  1. Uniformly loosen and remove the 8 bearing cap bolts in several steps in the sequence shown in the illustration.



    A221185E01
  1. Uniformly loosen and remove the 13 bearing cap bolts in several steps in the sequence shown in the illustration.

    NOTICE:
    Uniformly loosen the bolts while keeping the camshaft level.

  1. Remove the 5 camshaft bearing caps.

  1. Remove the No. 3 camshaft and No. 4 camshaft.



45. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH


    A221186E01
  1. Remove the camshaft housing sub-assembly LH by prying between the cylinder head and camshaft housing sub-assembly LH with a screwdriver.
    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head and camshaft housing sub-assembly LH.



46. REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
  1. Remove the 24 valve rocker arms from the cylinder head.

    HINT:
    Arrange the removed parts in the correct order.



47. REMOVE VALVE LASH ADJUSTER ASSEMBLY
  1. Remove the 24 valve lash adjusters from the cylinder head.

    HINT:
    Arrange the removed parts in the correct order.



48. REMOVE VALVE STEM CAP
  1. Remove the 24 valve stem caps from the cylinder head.

    HINT:
    Arrange the removed parts in the correct order.



49. REMOVE CYLINDER HEAD SUB-ASSEMBLY


    A221092E01
  1. Using a 10 mm bi-hexagon wrench, uniformly loosen the 8 cylinder head bolts in the sequence shown in the illustration. Remove the 8 cylinder head bolts and plate washers.

    NOTICE:
    1. Be careful not to drop washers into the cylinder head sub-assembly.
    2. Cylinder head warpage or cracking could result from removing bolts in an incorrect order.

    HINT:
    Arrange the removed parts in the correct order.

  1. Remove the cylinder head sub-assembly.



50. REMOVE CYLINDER HEAD LH


    A221093E01
  1. Uniformly loosen and remove the 2 cylinder head set bolts in several steps in the sequence shown in the illustration.



    A221094E01
  1. Using a 10 mm bi-hexagon wrench, uniformly loosen the 8 bolts in the sequence shown in the illustration. Remove the 8 cylinder head bolts and plate washers.

    NOTICE:
    1. Be careful not to drop washers into the cylinder head sub-assembly.
    2. Cylinder head warpage or cracking could result from removing bolts in an incorrect order.

    HINT:
    Be sure to keep the removed parts for each installation position separate.

  1. Remove the cylinder head LH.



51. REMOVE CYLINDER HEAD GASKET


52. REMOVE NO. 2 CYLINDER HEAD GASKET


53. REMOVE NO. 1 WATER OUTLET PIPE


    A227937
  1. Detach the 3 wire harness clamps.

  1. Remove the 2 nuts, bolt and water outlet pipe.



54. REMOVE KNOCK SENSOR


    A075662
  1. Disconnect the 2 sensor connectors.

  1. Remove the 2 bolts and 2 sensors.



55. REMOVE CYLINDER BLOCK WATER JACKET SPACER


A225372
  1. Remove the 2 water jacket spacers from the cylinder head.

    NOTICE:
    Be sure to remove the water jacket spacers. If not, they may fall and become damaged when the cylinder block is inverted.



56. REMOVE TAPER SCREW PLUG

NOTICE:
It is not necessary to remove a taper screw plug unless it is being replaced.



57. REMOVE STRAIGHT PIN

NOTICE:
It is not necessary to remove a straight pin unless it is being replaced.



58. REMOVE RING PIN

NOTICE:
It is not necessary to remove a ring pin unless it is being replaced.



59. REMOVE STUD BOLT

NOTICE:
It is not necessary to remove a stud bolt unless it is being replaced.