Home › BODY › WINDSHIELD / WINDOWGLASS › POWER WINDOW REGULATOR MOTOR (for Front Door)

POWER WINDOW REGULATOR MOTOR (for Front Door) > INSPECTION

for Preparation Click here



1. INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (w/o Jam Protection Function)


    B161799E05
  1. Apply battery voltage to connector terminals 1 and 2.

  1. Apply battery voltage to the regulator motor and check the operation of the front power window regulator motor assembly LH.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → 1
    Battery negative (-) → 2
    Motor gear rotates counterclockwise
    Battery positive (+) → 2
    Battery negative (-) → 1
    Motor gear rotates clockwise

    1. If the result is not as specified, replace the front power window regulator motor assembly LH.
      Text in Illustration 
      *1
      Motor Gear
      *a
      Component without harness connected
      (Front Power Window Regulator Motor Assembly LH)
      *b
      Clockwise
      *c
      Counterclockwise



2. INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (w/ Jam Protection Function)


E281626E01

NOTICE:
  1. Do not apply positive (+) battery voltage to any terminals except terminal 2, to avoid damaging the pulse sensor inside the motor.
  2. Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly to the door.

  1. Apply battery voltage to the regulator motor and check the operation of the front power window regulator motor assembly LH.

    OK:
    Measurement Condition
    Motor Condition
    Specified Condition
    Battery positive (+) → Terminal 2
    Battery negative (-) → Terminal 1, 4 and 10
    Auto
    Motor gear rotates clockwise
    Battery positive (+) → Terminal 2
    Battery negative (-) → Terminal 1, 4 and 7
    Motor gear rotates counterclockwise
    Battery positive (+) → Terminal 2
    Battery negative (-) → Terminal 1 and 10
    Manual
    Motor gear rotates clockwise
    Battery positive (+) → Terminal 2
    Battery negative (-) → Terminal 1 and 7
    Motor gear rotates counterclockwise

    If the result is not as specified, replace the front power window regulator motor assembly LH.
    Text in Illustration 
    *1
    Motor Gear
    *a
    Component without harness connected
    (Front Power Window Regulator Motor Assembly LH)
    *b
    Clockwise
    *c
    Counterclockwise



3. INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (w/o Jam Protection Function)


    B161800E04
  1. Apply battery voltage to connector terminals 1 and 2.

  1. Apply battery voltage to the regulator motor and check the operation of the front power window regulator motor assembly RH.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → 1
    Battery negative (-) → 2
    Motor gear rotates clockwise
    Battery positive (+) → 2
    Battery negative (-) → 1
    Motor gear rotates counterclockwise

    1. If the result is not as specified, replace the front power window regulator motor assembly RH.
      Text in Illustration 
      *1
      Motor Gear
      *a
      Component without harness connected
      (Front Power Window Regulator Motor Assembly RH)
      *b
      Clockwise
      *c
      Counterclockwise



4. INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (w/ Jam Protection Function)


E281625E01

NOTICE:
  1. Do not apply positive (+) battery voltage to any terminals except terminal 2, to avoid damaging the pulse sensor inside the motor.
  2. Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly to the door.

  1. Apply battery voltage to the regulator motor and check the operation of the front power window regulator motor assembly RH.

    OK:
    Measurement Condition
    Motor Condition
    Specified Condition
    Battery positive (+) → Terminal 2
    Battery negative (-) → Terminal 1, 4 and 7
    Auto
    Motor gear rotates clockwise
    Battery positive (+) → Terminal 2
    Battery negative (-) → Terminal 1, 4 and 10
    Motor gear rotates counterclockwise
    Battery positive (+) → Terminal 2
    Battery negative (-) → Terminal 1 and 7
    Manual
    Motor gear rotates clockwise
    Battery positive (+) → Terminal 2
    Battery negative (-) → Terminal 1 and 10
    Motor gear rotates counterclockwise

    If the result is not as specified, replace the front power window regulator motor assembly RH.
    Text in Illustration 
    *1
    Motor Gear
    *a
    Component without harness connected
    (Front Power Window Regulator Motor Assembly RH)
    *b
    Clockwise
    *c
    Counterclockwise