STARTER (for 1.6 kW Type) > INSPECTION |
| 1. INSPECT STARTER ASSEMBLY |
Perform a pull-in test.
Remove the nut and disconnect the lead wire from terminal C.
![]() |
Connect the battery to the starter as shown in the illustration. Then check that the clutch pinion gear moves outward.
| *1 | Terminal 50 |
| *2 | Terminal C |
Perform holding test.
![]() |
With the battery connected as above with the clutch pinion gear out, disconnect the negative (-) terminal lead from terminal C. Check that the pinion gear remains out.
| *1 | Terminal C |
![]() | Disconnect |
![]() |
Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear returns inward.
| *1 | Terminal 50 |
![]() | Disconnect |
Perform an operation test without load.
Connect the lead wire to terminal C.
Mount the starter in a vise between aluminum plates.
![]() |
Connect the battery and an ammeter to the starter as shown in the illustration.
| *1 | Terminal 50 |
| *2 | Terminal 30 |
Check that the starter rotates smoothly and steadily while the pinion gear is moving out. Then measure the current.
| 2. INSPECT STARTER ARMATURE ASSEMBLY |
Check the commutator for dirt and/or burns on the surface.
If the surface is dirty and/or burnt, correct it with sandpaper (No. 400) or lathe. If necessary, replace the starter armature assembly.
Inspect the commutator for an open circuit.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Segment - Segment | Always | Below 1 Ω |
| *1 | Segment |
Inspect the commutator for a short circuit.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Segment - Coil core | Always | 10 kΩ or higher |
| *1 | Segment |
| *2 | Coil Core |
![]() |
Using a vernier caliper, measure the protrusion length.
| *1 | Depth |
| 3. INSPECT STARTER COMMUTATOR END FRAME ASSEMBLY |
Check the brush length.
![]() |
Using a vernier caliper, measure the brush length.
| *1 | Length |
Inspect the insulation.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Positive (+) brush - Negative (-) brush | Always | 10 kΩ or higher |
| 4. INSPECT STARTER CENTER BEARING CLUTCH SUB-ASSEMBLY |
Check the gear teeth on the planetary gear, internal gear and starter clutch for wear or damage.
If any of the gears is damaged, replace the starter center bearing clutch sub-assembly.
Check the starter clutch pinion gear.
![]() |
Hold the starter clutch and rotate the pinion gear clockwise, and check that it turns freely. Try to rotate the pinion gear counterclockwise and check that it locks.
![]() | Free |
![]() | Lock |
| 5. INSPECT REPAIR SERVICE STARTER KIT |
Check the plunger.
![]() |
Push in the plunger, and check that it returns quickly to it is original position.
If the result is not as specified, replace the repair service starter kit.
Inspect the pull-in coil.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Terminals 50 - Terminal C | Always | Below 1 Ω |
| *1 | Terminal 50 |
| *2 | Terminal C |
Inspect the holding coil.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Terminal 50 - Switch body | Always | Below 2 Ω |
| *1 | Terminal 50 |
| *2 | Switch Body |