Home › ENGINE ยท 1GR-FE › STARTING › STARTER (for 1.6 kW Type)

STARTER (for 1.6 kW Type) > REASSEMBLY

for Preparation Click here



1. INSTALL STARTER CENTER BEARING CLUTCH SUB-ASSEMBLY


    A124187E08
  1. Apply high-temperature grease to the drive lever set pin, as shown in the illustration.
    Text in Illustration 
    V100135
    Apply High-temperature Grease



    A084665E08
  1. Install the drive lever set pin to the starter center bearing clutch.
    Text in Illustration 
    *1
    Drive Lever Set Pin
    *2
    Starter Center Bearing Clutch

  1. Install the starter center bearing clutch and drive lever set pin together to the starter drive housing.



2. INSTALL PLANETARY GEAR


    A076128E02
  1. Apply high-temperature grease to the planetary gears and pin parts of the planetary shaft.
    Text in Illustration 
    V100135
    Apply High-temperature Grease

  1. Install the 3 planetary gears into the pins of the starter center bearing clutch.



3. INSTALL STARTER ARMATURE ASSEMBLY


    A124190E07
  1. Apply high-temperature grease to the plate washer, bearing and a new snap ring.
    Text in Illustration 
    *1
    New Snap Ring
    *2
    Plate Washer
    *3
    Bearing
    V100135
    Apply High-temperature Grease

  1. Hold the starter commutator end frame assembly in a vise between aluminum plates.

    NOTICE:
    Do not overtighten the vise.

  1. Apply high-temperature grease to the armature shaft.

  1. Install the starter armature to the starter commutator end frame.

    NOTICE:
    Do not damage starter commutator end frame.

  1. Install the plate washer to the armature shaft.

  1. Using snap ring pliers, install the snap ring.

    NOTICE:
    1. Be sure to install the snap ring in the armature shaft groove securely.
    2. Be sure to properly install the snap ring because it expands easily.



  1. Check the snap ring length.



      A058810E29
    1. Using a vernier caliper, measure the snap ring length.

      Maximum length:
      5.0 mm (0.197 in.)
      Text in Illustration 
      *1
      Length

      If the length is more than the maximum, replace the snap ring.



4. INSTALL STARTER COMMUTATOR END FRAME COVER


    A094625E01
  1. Install the starter commutator end frame cover into the starter commutator end frame.



5. INSTALL STARTER ARMATURE PLATE


    A073991E27
  1. Align the claw of the armature plate with the groove inside the starter yoke, and install the starter armature plate.
    Text in Illustration 
    *1
    Claw
    *2
    Groove



6. INSTALL STARTER COMMUTATOR END FRAME ASSEMBLY


    A058587E02
  1. Align the starter commutator end frame rubber with the groove of the starter yoke.

  1. Install the starter commutator end frame to starter yoke.

    NOTICE:
    The magnet of the starter yoke may attract the starter armature when the starter commutator end frame is installed, causing the magnet to break.



7. INSTALL STARTER YOKE ASSEMBLY


    A076130E01
  1. Align the claw of the starter yoke with the groove inside the starter drive housing.

  1. Install the starter yoke with the 2 bolts.

    Torque:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }



8. INSTALL REPAIR SERVICE STARTER KIT


    A118287E06
  1. Apply high-temperature grease to the plunger and hook.
    Text in Illustration 
    V100135
    Apply High-temperature Grease



    A076131E01
  1. Hang the plunger hook of the repair service starter kit to the drive lever.

  1. Install the plunger and return spring.

  1. Install the repair service starter kit with the 2 screws.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the lead wire to the terminal C with the nut.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }