Home › STEERING › POWER STEERING › VANE PUMP (for 1UR-FE)

VANE PUMP (for 1UR-FE) > INSTALLATION

for Preparation Click here



1. INSTALL VANE PUMP ASSEMBLY


A163333E05

HINT:
Before performing the following procedures, move the spacer until the vane pump can be installed.

Text in Illustration 
*a
Spacer


    C161012
  1. Install the vane pump assembly with the 2 bolts.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }



2. INSTALL PRESSURE FEED TUBE
  1. Install a new gasket to the pressure feed tube.



    C161011E02
  1. Install the pressure feed tube with the union bolt.

    Torque:
    51 N*m{ 520 kgf*cm , 38 ft.*lbf }

    Text in Illustration 
    *1
    Pressure Feed Tube



3. CONNECT POWER STEERING OIL PRESSURE SENSOR CONNECTOR


    C161010
  1. Connect the power steering oil pressure sensor connector.



4. CONNECT NO. 1 OIL RESERVOIR TO PUMP HOSE


    C161009E02
  1. Connect the No. 1 oil reservoir to pump hose, and slide the clamp to secure it.
    Text in Illustration 
    *1
    Pump Hose



5. CONNECT WIRE HARNESS CLAMP


    C161008
  1. Connect the wire harness clamp.



6. INSTALL FAN AND GENERATOR V BELT


    A214821E01
  1. Attach the 2 V-bank cover hooks to the bracket. Then align the 2 V-bank cover grommets with the 2 pins, and press down on the V-bank cover to attach the pins.



7. INSTALL AIR CLEANER CASE SUB-ASSEMBLY


    A309638E01
  1. Install the air cleaner case with the 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Install the air cleaner element to the air cleaner case.



    A309637E01
  1. Install the air cleaner cap.

    1. for Type A:
      Install the air cleaner cap and fasten the 4 hook clamps.

    2. for Type B:
      Install the air cleaner cap and fasten the 2 hook clamps.

    3. Connect the MAF meter connector.

    4. Attach the wire harness clamp.



8. INSTALL V-BANK COVER SUB-ASSEMBLY


    A214821E01
  1. Attach the 2 V-bank cover hooks to the bracket. Then align the 2 V-bank cover grommets with the 2 pins, and press down on the V-bank cover to attach the pins.



9. ADD POWER STEERING FLUID


10. BLEED POWER STEERING FLUID
  1. Check the fluid level.

  1. Jack up the front of the vehicle and support it with stands.

  1. Turn the steering wheel.

    1. With the engine stopped, turn the wheel slowly from lock to lock several times.

  1. Lower the vehicle.

  1. Start the engine.

  1. Run the engine at idle for a few minutes.

  1. Turn the steering wheel.

    1. With the engine idling, turn the wheel left or right to the full lock position and keep it there for 2 to 3 seconds, and then turn the wheel to the opposite full lock position and keep it there for 2 to 3 seconds.*1

    2. Repeat *1 several times.

  1. Stop the engine.



    C124274E02
  1. Check for foaming or emulsification.
    If the system has to be bled twice because of foaming or emulsification, check for fluid leaks in the system.

  1. Check the fluid level.



11. INSPECT FOR POWER STEERING FLUID LEAK


12. INSTALL NO. 1 ENGINE UNDER COVER


    A150108
  1. Hook the engine under cover to the vehicle body as shown in the illustration.

  1. Install the 3 screws and 5 bolts.

    Torque:
    for bolt:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }
    for screw:
    3.0 N*m{ 31 kgf*cm , 27 in.*lbf }



13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
Some systems need to be initialized after the cable is reconnected (Click here).