Home › STEERING › POWER STEERING › STEERING GEAR

STEERING GEAR > DISASSEMBLY

for Preparation Click here



1. FIX POWER STEERING GEAR ASSEMBLY


    C159512E01
  1. Using SST, secure the power steering gear.

    SST
    09612-00012  

    HINT:
    Tape SST before use.

    NOTICE:
    When using a vise, do not overtighten it.



2. REMOVE TIE ROD END SUB-ASSEMBLY LH


    C154516E01
  1. Put matchmarks on the tie rod end LH and steering rack end.



3. REMOVE TIE ROD END SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



4. REMOVE STEERING RACK BOOT CLIP
  1. Using pliers, remove the 2 steering rack boot clips.



5. REMOVE NO. 2 STEERING RACK BOOT CLAMP


    C159523
  1. Using pliers, remove the 2 boot clamps as shown in the illustration.

    NOTICE:
    Be careful not to damage the No. 2 steering rack boot.



6. REMOVE NO. 2 STEERING RACK BOOT


7. REMOVE NO. 1 STEERING RACK BOOT


8. REMOVE STEERING RACK END SUB-ASSEMBLY


    ZX09339E01
  1. Using a screwdriver and hammer, stake back the washer.

    NOTICE:
    Do not strike the steering rack.

  1. Using a wrench, hold the steering rack (LH side).



    G038616E02
  1. Using SST, remove the steering rack end (LH side) from the power steering rack.

    SST
    09922-10010  

    NOTICE:
    Rotate SST in the direction shown in the illustration.

  1. Using SST, remove the steering rack end (RH side) from the power steering rack.

    SST
    09922-10010  

    NOTICE:
    Rotate SST in the direction shown in the illustration.

  1. Remove the 2 claw washers.



9. REMOVE STEERING GEAR RACK GUIDE


    C206204
  1. Using SST, remove the steering rack guide spring cap nut.

    SST
    09922-10010  

    NOTICE:
    Rotate SST in the direction shown in the illustration.



    C206205
  1. Using a 32 mm hexagon wrench, remove the rack guide spring cap.

  1. Remove the spring and rack guide.



10. REMOVE POWER STEERING CONTROL VALVE


    F051708E01
  1. Wind vinyl tape around the serrated portion of the control valve.

  1. Remove the dust cover from the control valve housing.



    G100343E01
  1. Remove the 2 bolts.

  1. Pull out the control valve from the rack housing.

  1. Remove the control valve oil seal.



    F051710E01
  1. To prevent the oil seal lip from getting damaged, wind vinyl tape around the serrated portion of the control valve.

  1. Using a plastic-faced hammer, remove the control valve from the control valve housing.



    F051711E01
  1. Using a screwdriver, remove the 4 control valve rings.

    NOTICE:
    Be careful not to damage the grooves for the control valve rings.



11. REMOVE POWER STEERING CONTROL VALVE UPPER OIL SEAL


    C206224E01
  1. Using SST and a press, remove the control valve upper bearing and control valve upper oil seal from the control valve housing.

    SST
    09950-60010   (09951-00250)
    09950-70010   (09951-07150)



12. REMOVE CYLINDER END STOPPER


    F051713
  1. Using a screwdriver and hammer, turn the cylinder end stopper clockwise until the wire end can be seen through the service hole.

  1. Using a screwdriver and hammer, turn the cylinder end stopper counterclockwise, and remove the wire and cylinder end stopper.



13. REMOVE POWER STEERING RACK


14. REMOVE POWER STEERING RACK BUSH
  1. Remove the rack bush from the power steering rack.

  1. Using a screwdriver, remove the O-ring from the rack bush.



    F051714E01
  1. Using SST, remove the rack bush oil seal.

    SST
    09527-21011  
    09612-24014   (09613-22011)



15. REMOVE POWER STEERING CYLINDER TUBE OIL SEAL


    F051715E01
  1. Using SST and a press, remove the cylinder tube oil seal.

    SST
    09950-60010   (09951-00320)
    09950-70010   (09951-07360)



16. REMOVE RACK STEERING PISTON RING


    R010955E02
  1. Using a screwdriver, remove the piston ring and O-ring.

    NOTICE:
    Be careful not to damage the groove for the piston ring.