Home › DRIVE LINE › PROPELLER SHAFT › PROPELLER SHAFT ASSEMBLY (for 2WD)

PROPELLER SHAFT ASSEMBLY (for 2WD) > INSTALLATION

for Preparation Click here



1. MEASURE EXTENSION HOUSING AND DIFFERENTIAL FLANGE ANGLE

NOTICE:
  1. Perform the inspection on a level surface.
  2. Perform the inspection with the vehicle empty.
  3. Perform the inspection with all wheels on the ground.

HINT:
As the extension housing and rear differential flange angles are necessary when measuring the installation angle of the propeller shaft, measure the angle of the extension housing and rear differential flange before installing the propeller shaft.



    C180329E03
  1. Using SST, measure and record the angle of the extension housing flange (A).

    SST
    09370-50010  
    Text in Illustration 
    *a
    Extension Housing Flange Angle: A



    C180330E02
  1. Using SST, measure and record the angle of the rear differential flange (B).

    SST
    09370-50010  
    Text in Illustration 
    *a
    Extension Housing Flange Angle: B



2. TEMPORARILY INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY
  1. Completely remove any oil or the like and clean the contact surfaces of the propeller shaft flange and differential flange.

  1. for A750E and A760E:
    Remove SST from the transmission.

    SST
    09325-40010  

  1. for AB60E:
    Remove SST from the transmission.

    SST
    09325-60010  

  1. Insert the sleeve yoke into the transmission.



  1. w/o Bearing Washer:



      C158583
    1. Temporarily install the center support bearing to the crossmember with the 2 mounting bolts.



  1. w/ Bearing Washer:



      C179315E02
    1. Temporarily install the center support bearing to the crossmember with the 2 bearing washers and 2 mounting bolts.
      Text in Illustration 
      *1
      No. 2 Center Support Bearing Washer
      *2
      No. 1 Center Support Bearing Assembly
      *a
      Frame



    C158582E03
  1. Align the matchmarks on the propeller shaft flange and differential flange.
    Text in Illustration 
    *a
    Matchmark

  1. Connect the propeller shaft to the differential side, and install the 4 bolts and 4 nuts.

    Torque:
    70 N*m{ 714 kgf*cm , 52 ft.*lbf }



3. TIGHTEN PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY


  1. With the vehicle empty and all 4 tires supported by a lift, or with the vehicle suspension in the full rebound position, adjust the center bearing so that dimension A (the distance from the front surface of the center bearing housing to the back surface of the intermediate shaft) is as shown in the chart below.

    HINT:
    Measure dimension A (the distance from the front surface of the center bearing housing to the back surface of the intermediate shaft) at 3 places and make adjustments so that the measured dimensions are equal.



    C172056E02


    Text in Illustration 
    *a
    Intermediate Shaft
    *b
    Dimension A
    *c
    Tires supported and vehicle empty (When using drive-on type lift)
    *d
    Full rebound position (When using 2 post lift)
    V100135
    Front Side
    -
    -

    Standard dimension A:

    Vehicle model
    Dimension A
    Tires supported and vehicle empty (When using drive-on type lift)
    Full rebound position (When using 2 post lift)
    GSK51L-CRASKA
    23.0 mm (0.906 in.)
    16.0 mm (0.630 in.)
    USK51L-CRTLKA*
    23.0 mm (0.906 in.)
    USK51L-CRTSKA*
    USK52L-CHTSKA
    21.0 mm (0.827 in.)
    USK52L-CHTSKA*
    USK51L-PSTSKA*
    24.0 mm (0.945 in.)
    USK51L-PSTLKA*
    UPK51L-CRTSKA
    UPK51L-CRTSKA*
    UPK51L-PSTSKA
    UPK51L-PSTSKA*
    GSK51L-THASKA
    23.0 mm (0.906 in.)
    USK51L-PSTZKA
    24.0 mm (0.945 in.)
    USK51L-THTSKA
    21.0 mm (0.827 in.)
    USK51L-THTSKA*

    *: includes Off road package



    C160089E02
  1. Check that the center line of the bracket is at right angles to the shaft axial direction.

  1. Tighten the 2 mounting bolts.

    Torque:
    40 N*m{ 410 kgf*cm , 30 ft.*lbf }

    Text in Illustration 
    *a
    90°
    *b
    Bracket Center Line
    *c
    Shaft Axial Direction



4. INSPECT PROPELLER SHAFT ANGLE

NOTICE:
  1. Perform the inspection on a level surface.
  2. Perform the inspection with the vehicle empty.
  3. Perform the inspection with all wheels on the ground.



  1. Measure the No. 1 joint angle.



    1. Using SST, measure and record the angle of the intermediate shaft (C).


      C180167E02

      SST
      09370-50010  

      Text in Illustration 
      *a
      Intermediate Shaft Angle: C
      -
      -



    2. C180168E02
    3. Subtract the angle of the extension housing flange (A) measured before installing the propeller shaft from the angle of the intermediate shaft (C) to calculate the No. 1 joint angle.

      No. 1 joint angle:
      Angle of intermediate shaft (C) - Angle of extension housing flange (A)

      Measured Value (Reference):
      Intermediate Shaft Angle Measured Value (C)
      Extension Housing Flange Angle Measured Value (A)
      No. 1 Joint Angle (Calculated Value)
      (C) - (A)
      3°15' (3.25°)
      4°00' (4.00°)
      -0°45' (-0.75°)

      Text in Illustration 
      *a
      No. 1 Joint Angle

      HINT:
      1. Using the following chart, check if the calculated No. 1 joint angle is within the specified value.
      2. The tolerance is +/-0°60' (1.00°).


      Standard No. 1 joint angle:

      Vehicle model
      No. 1 joint angle
      GSK51L-CRASKA
      -0°02' +/-0°60' (-0.03° +/-1.00°)
      USK51L-CRTSKA
      USK51L-CRTLKA
      0°41' +/-0°60' (0.68° +/-1.00°)
      USK51L-CRTSKA*
      USK51L-CRTLKA*
      0°41' +/-0°60' (0.68° +/-1.00°)
      USK52L-CHTSKA
      0°58' +/-0°60' (0.97° +/-1.00°)
      USK52L-CHTSKA*
      0°57' +/-0°60' (0.96° +/-1.00°)
      USK51L-PSTSKA
      USK51L-PSTLKA
      0°41' +/-0°60' (0.68° +/-1.00°)
      USK51L-PSTSKA*
      USK51L-PSTLKA*
      0°41' +/-0°60' (0.68° +/-1.00°)
      UPK51L-CRTSKA
      0°41' +/-0°60' (0.69° +/-1.00°)
      UPK51L-CRTSKA*
      0°41' +/-0°60' (0.68° +/-1.00°)
      UPK51L-PSTSKA
      UPK51L-PSTSKA*
      0°41' +/-0°60' (0.68° +/-1.00°)
      GSK51L-THASKA
      -0°02' +/-0°60' (-0.03° +/-1.00°)
      USK51L-PSTZKA
      0°41' +/-0°60' (0.68° +/-1.00°)
      USK51L-THTSKA
      USK51L-THTSKA*
      0°41' +/-0°60' (0.68° +/-1.00°)

      *: includes Off road package
      1. If the measured angle is not within the specification, adjust it with the bearing washer (See "Adjust Propeller Shaft Angle").



  1. Measure the No. 2 joint angle.



    1. Using SST, measure and record the angle of the propeller shaft (D).


      C180169E02

      SST
      09370-50010  

      Text in Illustration 
      *a
      Intermediate Shaft Angle: D
      -
      -



    2. Subtract the angle of the propeller shaft (D) from the angle of the intermediate shaft (C) to calculate the No. 2 joint angle.


      C180170E02

      No. 2 joint angle:
      Angle of intermediate shaft (C) - Angle of propeller shaft (D)


      Measured Value (Reference):

      Intermediate Shaft Angle Measured Value (C)
      Propeller Shaft Angle Measured Value (D)
      No. 2 Joint Angle (Calculated Value)
      (C) - (D)
      3°15' (3.25°)
      5°30' (5.50°)
      -2°15' (-2.25°)


      Text in Illustration 
      *a
      No. 2 Joint Angle
      -
      -

      HINT:
      1. Using the following chart, check if the calculated No. 2 joint angle is within the specified value.
      2. The tolerance is +/-0°60' (1.00°).


      Standard No. 2 joint angle:

      Vehicle model
      No. 2 joint angle
      GSK51L-CRASKA
      -1°34' +/-0°60' (-1.57° +/-1.00°)
      USK51L-CRTSKA
      USK51L-CRTLKA
      -2°02' +/-0°60' (-2.03° +/-1.00°)
      USK51L-CRTSKA*
      USK51L-CRTLKA*
      -1°47' +/-0°60' (-1.78° +/-1.00°)
      USK52L-CHTSKA
      -1°17' +/-0°60' (-1.28° +/-1.00°)
      USK52L-CHTSKA*
      -0°51' +/-0°60' (-0.85° +/-1.00°)
      USK51L-PSTSKA
      USK51L-PSTLKA
      -2°25' +/-0°60' (-2.42° +/-1.00°)
      USK51L-PSTSKA*
      USK51L-PSTLKA*
      -2°06' +/-0°60' (-2.10° +/-1.00°)
      UPK51L-CRTSKA
      -2°14' +/-0°60' (-2.24° +/-1.00°)
      UPK51L-CRTSKA*
      -1°56' +/-0°60' (-1.93° +/-1.00°)
      UPK51L-PSTSKA
      -1°52' +/-0°60' (-1.87° +/-1.00°)
      UPK51L-PSTSKA*
      -1°56' +/-0°60' (-1.93° +/-1.00°)
      GSK51L-THASKA
      -1°23' +/-0°60' (-1.39° +/-1.00°)
      USK51L-PSTZKA
      -2°11' +/-0°60' (-2.19° +/-1.00°)
      USK51L-THTSKA
      -2°58' +/-0°60' (-2.97° +/-1.00°)
      USK51L-THTSKA*
      -2°52' +/-0°60' (-2.87° +/-1.00°)

      *: includes Off road package
      1. If the measured angle is not within the specification, adjust it with the bearing washer (See "Adjust Propeller Shaft Angle").



  1. Measure the No. 3 joint angle.



    1. Subtract the angle of the rear differential flange (B) measured before installing the propeller shaft from the angle of the propeller shaft (D) to calculate the No. 3 joint angle.


      C180171E02

      No. 3 joint angle:
      Angle of propeller shaft (D) - Angle of rear differential flange (B)


      Measured Value (Reference):

      Propeller Shaft Angle Measured Value (D)
      Rear Differential Flange Angle Measured Value (B)
      No. 3 Joint Angle (Calculated Value)
      (D) - (B)
      5°30' (5.50°)
      1°15' (1.25°)
      4°15' (4.25°)


      Text in Illustration 
      *a
      No. 3 Joint Angle
      -
      -

      HINT:
      1. Using the following chart, check if the calculated No. 3 joint angle is within the specified value.
      2. The tolerance is +/-0°60' (1.00°).


      Standard No. 3 joint angle:

      Vehicle model
      No. 3 joint angle
      GSK51L-CRASKA
      3°34' +/-0°60' (3.57° +/-1.00°)
      USK51L-CRTSKA
      USK51L-CRTLKA
      2°50' +/-0°60' (2.83° +/-1.00°)
      USK51L-CRTSKA*
      USK51L-CRTLKA*
      2°34' +/-0°60' (2.57° +/-1.00°)
      USK52L-CHTSKA
      3°17' +/-0°60' (3.28° +/-1.00°)
      USK52L-CHTSKA*
      2°52' +/-0°60' (2.87° +/-1.00°)
      USK51L-PSTSKA
      USK51L-PSTLKA
      4°12' +/-0°60' (4.20° +/-1.00°)
      USK51L-PSTSKA*
      USK51L-PSTLKA*
      3°53' +/-0°60' (3.88° +/-1.00°)
      UPK51L-CRTSKA
      3°31' +/-0°60' (3.52° +/-1.00°)
      UPK51L-CRTSKA*
      3°14' +/-0°60' (3.23° +/-1.00°)
      UPK51L-PSTSKA
      3°40' +/-0°60' (3.67° +/-1.00°)
      UPK51L-PSTSKA*
      3°43' +/-0°60' (3.72° +/-1.00°)
      GSK51L-THASKA
      3°23' +/-0°60' (3.39° +/-1.00°)
      USK51L-PSTZKA
      3°59' +/-0°60' (3.98° +/-1.00°)
      USK51L-THTSKA
      4°13' +/-0°60' (4.22° +/-1.00°)
      USK51L-THTSKA*
      3°37' +/-0°60' (3.62° +/-1.00°)

      *: includes Off road package
      1. If the measured angle is not within the specification, adjust it with the bearing washer (See "Adjust Propeller Shaft Angle").



5. ADJUST PROPELLER SHAFT ANGLE

HINT:
If the propeller shaft angle is outside the specification or there is vibration and noise, perform the propeller shaft adjustment using the following procedure.

  1. Adjust the No. 1, No. 2 and No. 3 joint angle.

    1. Support the propeller shaft with a jack.

    2. Remove the 2 center bearing mounting bolts.

    3. Slowly lower the jack, and disconnect the center bearing.

    4. Select an appropriate center support bearing washer thickness from the table below, and obtain a washer set.

      Standard bearing washer thickness:
      Thickness
      2.0 mm (0.0787 in.)
      4.5 mm (0.1772 in.)
      6.5 mm (0.2559 in.)
      9.0 mm (0.3543 in.)
      11.0 mm (0.4331 in.)
      13.5 mm (0.5315 in.)

      HINT:
      1. Each set contains 2 washers.
      2. Using the washer set, perform the adjustment.
      3. As a reference when selecting a bearing washer, the angle changes as follows for every 1.0 mm (0.0394 in.) change in bearing washer thickness.

        Angle variation for every 1.0 mm (0.0394 in.) change in bearing washer thickness:
        No. 1 joint angle:
        0°04' (0.06°)
        No. 2 joint angle:
        0°07' (0.12°)
        No. 3 joint angle:
        0°04' (0.06°)



6. INSPECT FOR OIL LEAK