Home › DRIVE LINE › WF1AM TRANSFER › TRANSFER ASSEMBLY

TRANSFER ASSEMBLY > DISASSEMBLY

for Preparation Click here



1. REMOVE LOWER TRANSFER CASE PROTECTOR
  1. Remove the 4 bolts and lower transfer case protector.



2. REMOVE WIRING HARNESS CLAMP BRACKET


    C291193
  1. Remove the 3 bolts and 3 wiring harness clamp brackets.



    C291143
  1. Disconnect the connector and 3 clamps.

  1. Remove the 2 bolts and wiring harness clamp bracket.



3. REMOVE TRANSFER SHIFT ACTUATOR ASSEMBLY


    C291190
  1. Disconnect the 3 connectors and detach the 2 clamps.

  1. Remove the 4 bolts and transfer shift actuator assembly.



4. REMOVE OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY (REAR)


    C291146E01
  1. Using a chisel and hammer, loosen the staked part of the transfer output shaft nut.

    NOTICE:
    1. Completely loosen the staked part of the transfer output shaft nut when removing it.
    2. Do not damage the threads of the rear transfer output shaft.

  1. Using SST, hold the output shaft companion flange sub-assembly (rear).

    SST
    09330-00021  
    Text in Illustration 
    *a
    Hold
    *b
    Turn

  1. Using a 30 mm socket wrench, remove the transfer output shaft nut.

  1. Remove the O-ring.



    C291147E01
  1. Using SST, remove the output shaft companion flange sub-assembly (rear).

    SST
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04031, 09957-04010, 09958-04011)
    Text in Illustration 
    *a
    Hold
    *b
    Turn



5. REMOVE TRANSFER OUTPUT SHAFT TYPE T OIL SEAL


    C291148E01
  1. Using SST, remove the transfer output shaft type T oil seal.

    SST
    09308-10010  

    NOTICE:
    Be careful not to damage the transfer output shaft type T oil seal and rear transfer case contact surface.



6. REMOVE TRANSFER INDICATOR SWITCH


    C291191E01
  1. Disconnect the connector and detach the clamp.

  1. Using SST, remove the transfer indicator switch.

    SST
    09224-00010  



7. REMOVE REAR TRANSFER CASE


    C291150
  1. Using a 40 IP ''TORX PLUS'' socket wrench or T40 ''TORX'' socket wrench, remove the 17 bolts.

  1. Remove the rear transfer case.

    HINT:
    If necessary, tap the rear transfer case with a plastic-faced hammer to remove it.



8. REMOVE SOLENOID COIL SUB-ASSEMBLY
  1. Disconnect the solenoid coil sub-assembly terminal.



    C291151
  1. Remove the 3 nuts and solenoid coil sub-assembly.

    NOTICE:
    Be careful not to drop the solenoid coil sub-assembly.



9. REMOVE TRANSFER COVER TYPE T OIL SEAL


    C291152E01
  1. Using a screwdriver, remove the transfer cover type T oil seal.
    Text in Illustration 
    *a
    Protective Tape

    NOTICE:
    Do not damage the rear transfer case.

    HINT:
    Tape the screwdriver tip before use.



10. REMOVE TRANSFER DRIVEN SPROCKET BEARING (REAR)


    C291153E02
  1. Using SST, remove the transfer driven sprocket bearing (rear).

    SST
    09612-65014   (09612-01040)
    Text in Illustration 
    *a
    Hold
    *b
    Turn



11. REMOVE REAR TRANSFER OUTPUT SHAFT RADIAL BALL BEARING


    C291154E01
  1. Using a screwdriver, remove the transfer output shaft rear shaft snap ring.
    Text in Illustration 
    *a
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.

  1. Remove the rear transfer output shaft radial ball bearing.



12. REMOVE SOLENOID COVER


    C291155E01
  1. Remove the No. 1 transfer output shaft spacer and solenoid cover.
    Text in Illustration 
    *1
    No. 1 Transfer Output Shaft Spacer
    *2
    Solenoid Cover



13. REMOVE TRANSFER SELECT RETURN SPRING


    C291156
  1. Remove the transfer select return spring.



14. REMOVE TRANSFER HIGH AND LOW SHIFT FORK SHAFT


    C291157
  1. Remove the transfer high and low shift fork shaft.



15. REMOVE SOLENOID LOCK PLATE WITH NO. 2 TRANSFER GEAR SHIFT FORK


    C291158E01
  1. Remove the solenoid lock plate together with the No. 2 transfer gear shift fork.
    Text in Illustration 
    *1
    Solenoid Lock Plate
    *2
    No. 2 Transfer Gear Shift Fork

  1. Remove the No. 2 transfer gear shift fork from the solenoid lock plate.



16. REMOVE CONTROL SELECT SHAFT SUB-ASSEMBLY


    C291160E01
  1. Remove the No. 1 transfer gear shift fork from the side of the control select shaft sub-assembly as shown in the illustration. Then remove the control select shaft sub-assembly.
    Text in Illustration 
    *1
    No. 1 Transfer Gear Shift Fork
    *2
    Control Select Shaft Sub-assembly



17. REMOVE TRANSFER DRIVE SPROCKET SUB-ASSEMBLY


    C291161E01
  1. Remove the transfer drive sprocket sub-assembly together with the front transfer drive chain and transfer driven sprocket.
    Text in Illustration 
    *1
    Transfer Drive Sprocket Sub-assembly
    *2
    Front Transfer Drive Chain
    *3
    Transfer Driven Sprocket

    NOTICE:
    Do not drop the transfer drive sprocket sub-assembly, front transfer drive chain and transfer driven sprocket.

  1. Remove the transfer drive sprocket sub-assembly and transfer driven sprocket from the front transfer drive chain.



18. REMOVE TRANSFER OIL PUMP BODY SUB-ASSEMBLY


    C291162E01
  1. Using a T25 ''TORX'' socket wrench, remove the bolt and the transfer oil pump body sub-assembly together with the transfer oil tube and transfer oil strainer sub-assembly.
    Text in Illustration 
    *1
    Transfer Oil Pump Body Sub-assembly
    *2
    Transfer Oil Tube
    *3
    Transfer Oil Strainer Sub-assembly

    HINT:
    The sleeve does not have to be removed.
    The transfer oil strainer sub-assembly comes with the sleeve installed.

  1. Remove the transfer oil tube from the transfer oil pump body sub-assembly.

  1. Remove the transfer oil strainer sub-assembly from the transfer oil tube.



19. REMOVE TRANSFER CASE MAGNET


    C291163
  1. Remove the transfer case magnet.



20. REMOVE NO. 1 TRANSFER GEAR SHIFT FORK


    C291164
  1. Remove the No. 1 transfer gear shift fork.

  1. Inspect the gear shift fork pad .



    C291207
  1. Remove the 2 gear shift fork pads from the No. 1 transfer gear shift fork.

    HINT:
    It is not necessary to remove the 2 gear shift fork pads unless they are being replaced.



21. REMOVE REAR TRANSFER OUTPUT SHAFT


    C291165
  1. Remove the rear transfer output shaft.



22. REMOVE TRANSFER HIGH AND LOW CLUTCH SLEEVE


    C291166E01
  1. Remove the transfer high and low clutch sleeve, No. 2 transfer output shaft spacer and transfer lower planetary gear bearing.
    Text in Illustration 
    *1
    Transfer High and Low Clutch Sleeve
    *2
    No. 2 Transfer Output Shaft Spacer
    *3
    Transfer Lower Planetary Gear Bearing



23. REMOVE TRANSFER LOWER PLANETARY GEAR ASSEMBLY


    C291167
  1. Remove the transfer lower planetary gear assembly.



    C291168E01
  1. Using SST, remove the transfer input gear radial ball bearing.

    SST
    09950-00020  
    09950-00030  
    09950-60010   (09951-00480)
    Text in Illustration 
    *a
    Hold
    *b
    Turn



24. REMOVE TRANSFER LOWER PLANETARY RING GEAR


    C291169E01
  1. Using a screwdriver, remove the transfer lower planetary ring gear hole snap ring.
    Text in Illustration 
    *a
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.

  1. Remove the transfer lower planetary ring gear.



25. REMOVE TRANSFER OIL SEPARATOR


    C291201
  1. Using a T25 ''TORX'' socket wrench, remove the bolt and transfer oil separator.



26. REMOVE OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY (FRONT)


    C291170
  1. Using a snap ring expander, remove the shaft snap ring and output shaft companion flange sub-assembly (front).

    NOTICE:
    Do not drop the output shaft companion flange sub-assembly (front).



27. REMOVE NO. 2 TRANSFER CASE OIL SEAL


    C291171E01
  1. Using SST, remove the No. 2 transfer case oil seal.

    SST
    09612-65014   (09612-01020)
    Text in Illustration 
    *a
    Hold
    *b
    Turn



28. REMOVE TRANSFER DRIVEN SPROCKET BEARING (FRONT)


    C291172E01
  1. Using SST and a press, press out the transfer driven sprocket bearing (front).

    SST
    09950-60010   (09951-00390, 09952-06010)
    09950-60020   (09951-00730)
    09950-70010   (09951-07100)



29. REMOVE TRANSFER CASE OIL SEAL


    C291177E01
  1. Using SST, remove the transfer case oil seal.

    SST
    09612-65014   (09612-01020)
    Text in Illustration 
    *a
    Hold
    *b
    Turn