Home › SERVICE SPECIFICATIONS › SERVICE SPECIFICATIONS › 1GR-FE ENGINE CONTROL SYSTEM

1GR-FE ENGINE CONTROL SYSTEM > SERVICE DATA



Camshaft Timing Oil Control Valve 
Tester Connection
Condition
Specified Condition
1 - 2
20°C (68°F)
6.9 to 7.9 Ω

Crankshaft Position Sensor 
Tester Connection
Condition
Specified Condition
1 - 2
Cold
1630 to 2740 Ω
Hot
2065 to 3225 Ω

Engine Coolant Temperature Sensor 
Tester Connection
Condition
Specified Condition
1 - 2
Approx. 20°C (68°F)
2.32 to 2.59 kΩ
Approx. 80°C (176°F)
0.310 to 0.326 kΩ

Throttle Body 
Tester Connection
Condition
Specified Condition
2 (M+) - 1 (M-)
20°C (68°F)
0.3 to 100 Ω

Knock Sensor 
Tester Connection
Condition
Specified Condition
1 - 2
20°C (68°F)
120 to 280 kΩ

Accelerator Pedal 
Accelerator Pedal Operation
Accelerator Position No. 1
Accelerator Position No. 2
Released
0.5 to 1.1 V
1.2 to 2.0 V
Depressed
2.6 to 4.5 V
3.4 to 4.9 V

Air Fuel Ratio Sensor (for Bank 1) 
Tester Connection
Condition
Specified Condition
1 (HA1A) - 2 (+B)
20°C (68°F)
1.6 to 3.2 Ω
1 (HA1A) - 4 (A1A-)
Always
10 kΩ or higher

Air Fuel Ratio Sensor (for Bank 2) 
Tester Connection
Condition
Specified Condition
1 (HA2A) - 2 (+B)
20°C (68°F)
1.6 to 3.2 Ω
1 (HA2A) - 4 (A2A-)
Always
10 kΩ or higher

Heated Oxygen Sensor (for Bank 1) 
Tester Connection
Condition
Specified Condition
1 (HT1B) - 2 (+B)
20°C (68°F)
11 to 16 Ω
1 (HT1B) - 4 (E2)
Always
10 kΩ or higher

Heated Oxygen Sensor (for Bank 2) 
Tester Connection
Condition
Specified Condition
1 (HT2B) - 2 (+B)
20°C (68°F)
11 to 16 Ω
1 (HT2B) - 4 (E2)
Always
10 kΩ or higher

Integration Relay (IG2) 
Tester Connection
Condition
Specified Condition
IG2 MAIN fuse
Always
Below 1 Ω
1C-1 - 1B-8
When battery voltage is not applied between 1B- 6 and 1B-7
10 kΩ or higher
When battery voltage is applied between 1B-6 and 1B-7
Below 1 Ω

Integration Relay (EFI) 
Tester Connection
Condition
Specified Condition
EFI fuse
Always
Below 1 Ω
1C-1 - 1B-4
When battery voltage is not applied between 1B- 2 and 1B-3
10 kΩ or higher
When battery voltage is applied between 1B-2 and 1B-3
Below 1 Ω
1C-1 - 1B-5
When battery voltage is not applied between 1B- 2 and 1B-3
10 kΩ or higher
When battery voltage is applied between 1B-2 and 1B-3
Below 1 Ω

Fuel Pump Relay (F/PMP) 
Tester Connection
Condition
Specified Condition
3 - 5
When battery voltage is not applied to terminals 1 and 2
10 kΩ or higher
When battery voltage is applied to terminals 1 and 2
Below 1 Ω

Integration Relay (A/F) 
Tester Connection
Condition
Specified Condition
A/F fuse
Always
Below 1 Ω
1C-1 - 1A-4
When battery voltage is not applied between 1A- 2 and 1A-3
10 kΩ or higher
When battery voltage is applied between 1A-2 and 1A-3
Below 1 Ω

Air Injection VSV Relay (AI-VSV) 
Tester Connection
Condition
Specified Condition
3 - 5
When battery voltage is not applied to terminals 1 and 2
10 kΩ or higher
When battery voltage is applied to terminals 1 and 2
Below 1 Ω