STARTER > INSTALLATION |
| 1. INSTALL STARTER ASSEMBLY |
![]() |
Install the flywheel housing side cover.
Install the starter with the 2 bolts.
Install the starter wire with the nut.
Connect the starter connector.
Attach the 2 wire harness clamps.
| 2. INSTALL STARTER COVER |
Install the starter cover with the 3 bolts.
| 3. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH |
![]() |
Install a new gasket to the cylinder head and a new gasket to the No. 2 air tube.
![]() |
Temporarily install the exhaust manifold and then uniformly tighten 8 new nuts that are not labeled A. Then tighten the new nuts labeled A in the illustration.
| 4. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR |
![]() |
Install the heat insulator with the 3 bolts.
| 5. INSTALL FRONT EXHAUST PIPE ASSEMBLY |
Install a new gasket and the exhaust pipe to the exhaust manifold RH with 3 new nuts.
Install a new gasket and the exhaust pipe to the center exhaust pipe with the 2 bolts.
Connect the air fuel ratio sensor connector.
Connect the heated oxygen sensor connector and attach the 2 clamps.
| 6. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE |
Apply a light coat of engine oil to a new O-ring.
![]() |
Install the O-ring to the guide.
Install the dipstick guide with the bolt.
Install the dipstick.
| 7. INSTALL GENERATOR ASSEMBLY |
![]() |
Install the generator with the 3 bolts and nut.
![]() |
Connect the generator connector.
Connect the generator wire with the nut.
Install the terminal cap.
![]() |
Install the harness bracket to the generator with the bolt.
| 8. CONNECT VANE PUMP ASSEMBLY |
![]() |
![]() |
Connect the vane pump to the timing chain cover with the 2 bolts.
![]() |
Attach the 2 clamps and connect the power steering oil pressure switch connector.
| 9. INSTALL FRONT FENDER APRON SEAL RH |
Install the apron seal with the 5 clips.
| 10. INSTALL FAN AND GENERATOR V BELT |
![]() |
Set the V belt onto every part.
While turning the belt tensioner counterclockwise, remove the pin.
![]() |
After installing the belt, check that it fits properly in the ribbed grooves.
| 11. INSTALL AIR CLEANER ASSEMBLY |
![]() |
Install the air cleaner case with the 2 bolts.
Install the air cleaner element onto the air cleaner case.
![]() |
Install the air cleaner cap.
for Type A:
Install the air cleaner cap and fasten the 4 hook clamps.
for Type B:
Install the air cleaner cap and fasten the 2 hook clamps.
Connect the MAF meter connector.
Attach the wire harness clamp.
| 12. INSTALL AIR CLEANER HOSE ASSEMBLY |
Install the air cleaner hose assembly with the 2 hose clamps.
Connect the vacuum hose to the air cleaner hose assembly.
Connect the ventilation hose to the air cleaner hose assembly, and slide the clamp to secure the hose.
| 13. INSTALL V-BANK COVER SUB-ASSEMBLY |
![]() |
Attach the 2 V-bank cover hooks to the No. 1 V-bank cover bracket. Then align the 2 V-bank cover grommets with the 2 pins, and press down on the V-bank cover sub-assembly to attach the pins.
| *1 | V-bank Cover Grommet |
| *2 | Pin |
| *3 | No. 1 V-bank Cover Bracket |
| *4 | V-bank Cover Hook |
| 14. INSTALL NO. 1 ENGINE UNDER COVER |
![]() |
Hook the engine under cover to the vehicle body as shown in the illustration.
Install the 3 screws and 5 bolts.
| 15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |