Home › ENGINE ยท 1GR-FE › LUBRICATION › OIL AND OIL FILTER

OIL AND OIL FILTER > REPLACEMENT

for Preparation Click here


CAUTION:
  1. Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.
  2. Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Protective clothing and gloves that cannot be penetrated by oil should be worn. The skin should be washed with soap and water, or use waterless hand cleaner, to remove any used engine oil thoroughly. Do not use gasoline, thinners, or solvents.
  3. In order to protect the environment, used oil and used oil filters must be disposed of at designated disposal sites.



1. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil pan drain plug and drain the engine oil into a container.

  1. Install a new gasket and the oil pan drain plug.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



2. REMOVE OIL FILTER ELEMENT


    A094910E09
  1. Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.
    Text in Illustration 
    *1
    Pipe
    *2
    Hose



    A222100
  1. Remove the oil filter drain plug.



    A222101E01
  1. Install the pipe to the oil filter cap.
    Text in Illustration 
    *1
    Cap
    *2
    Valve
    *3
    Pipe
    *4
    O-Ring
    *5
    Hose

    NOTICE:
    If the O-ring is removed with the oil filter drain plug, install the O-ring together with the pipe.

    HINT:
    Use a container to catch the draining oil.



    A222102
  1. Check that oil is drained from the oil filter. Then, disconnect the pipe as shown in the illustration and remove the O-ring.



    A222103E01
  1. Using SST, remove the oil filter cap.

    SST
    09228-06501  
    Text in Illustration 
    *1
    Oil Filter Bracket Clip

    NOTICE:
    Do not remove the oil filter bracket clip.



    A153538E03
  1. Remove the oil filter element and O-ring from the oil filter cap.
    Text in Illustration 
    *1
    O-Ring

    NOTICE:
    Be sure to remove the O-ring (for the oil filter cap) by hand, without using any tools, to prevent damage to the groove for the O-ring in the oil filter cap.



3. INSTALL OIL FILTER ELEMENT
  1. Clean the inside of the oil filter cap, the threads and O-ring groove.



    A284599E01
  1. Apply a small amount of engine oil to a new O-ring and install the O-ring to the oil filter cap.
    Text in Illustration 
    *1
    O-Ring
    *a
    CORRECT
    *b
    INCORRECT

    NOTICE:
    1. Be sure to install the O-ring in the proper location, otherwise oil may leak.
    2. Do not twist the O-ring.

  1. Set a new oil filter element on the oil filter cap.

  1. Remove any dirt or foreign matter from the installation surface of the engine.

  1. Apply a small amount of engine oil to the O-ring again and temporarily install the oil filter cap.



    A284600E01
  1. Using SST, tighten the oil filter cap.

    SST
    09228-06501  

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    Text in Illustration 
    *1
    Oil Filter Bracket
    *2
    O-Ring
    *3
    Oil Filter Cap
    *4
    Oil Filter Bracket Clip
    *a
    No Gap

    NOTICE:
    1. When tightening the oil filter cap, do not remove the oil filter bracket clip.
    2. Make sure that the oil filter is installed securely as shown in the illustration.
    3. Make sure that the O-ring does not get caught between the parts.
    4. After tightening the oil filter cap, make sure that there is no gap and that the O-ring is not protruding.



    A222105E01
  1. Apply a small amount of engine oil to a new drain plug O-ring and install the O-ring to the oil filter cap.
    Text in Illustration 
    *1
    O-Ring

    NOTICE:
    Before installing the O-ring, remove any dirt or foreign matter from the installation surface of the oil filter cap.

  1. Install the oil filter drain plug.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }

    NOTICE:
    Make sure that the O-ring does not get caught between the parts.



4. ADD ENGINE OIL


    A308107
  1. Add fresh oil.

    Standard Oil Grade:
    Oil grade
    Oil Viscosity (SAE)
    ILSAC GF-5 multigrade engine oil
    0W-20

    Standard Oil Capacity:
    Item
    Specified Condition
    Drain and refill without oil filter change
    5.6 liters (5.9 US qts, 4.9 Imp. qts)
    Drain and refill with oil filter change
    6.1 liters (6.4 US qts, 5.4 Imp. qts)
    Dry fill
    7.0 liters (7.4 US qts, 6.2 Imp. qts)

    NOTICE:
    Do not allow engine oil to adhere to the moving parts of the belt tensioner, as this may cause malfunctions.

    If engine oil is on the location indicated by the arrow, replace the belt tensioner.



5. CHECK ENGINE OIL LEVEL
  1. Warm up the engine, and then stop the engine and wait for 5 minutes.

  1. Check that the engine oil level is between the low level and full level marks on the dipstick.
    If low, check for leakage and add oil up to the full level mark.

    NOTICE:
    Do not fill engine oil above the full level mark.

    HINT:
    A certain amount of engine oil will be consumed while driving. In the following situations, oil consumption may increase, and engine oil may need to be refilled in between oil maintenance intervals.
    1. When the engine is new, for example directly after purchasing the vehicle or after replacing the engine.
    2. If low quality oil or oil of an inappropriate viscosity is used.
    3. When driving at high engine speed or with a heavy load, (when towing, or), when driving while accelerating or decelerating frequently.
    4. When leaving the idling for a long time, or when driving frequently through heavy traffic.
    When judging the amount of oil consumption, keep in mind that the oil may have become diluted, making it difficult to judge the true level accurately.



6. INSPECT FOR ENGINE OIL LEAK
  1. Start the engine. Make sure that there are no oil leaks from the area that was worked on.