CYLINDER HEAD > INSPECTION |
| 1. INSPECT CAMSHAFT OIL CLEARANCE |
Clean the bearing caps, camshaft housing and camshaft journals.
Place the camshafts on the camshaft housing.
![]() |
Lay a strip of Plastigage across each of the camshaft journals.
Install the camshaft bearing caps .
Install the camshaft housing .
Remove the camshaft bearing caps .
![]() |
Measure the Plastigage at its widest point.
| Item | Specified Condition |
| No. 1 journal | 0.030 to 0.065 mm (0.00118 to 0.00256 in.) |
| Other journals | 0.025 to 0.062 mm (0.000984 to 0.00244 in.) |
| Item | Specified Condition |
| No. 1 journal | 0.10 mm (0.00394 in.) |
| Other journals | 0.09 mm (0.00354 in.) |
| 2. INSPECT CAMSHAFT THRUST CLEARANCE |
Inspect the LH side camshafts.
Install the LH side camshafts.
![]() |
Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.
Inspect the RH side camshafts.
Install the RH side camshafts.
Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.
| 3. INSPECT COMPRESSION SPRING |
![]() |
Using a vernier caliper, measure the free length of the inner compression spring.
![]() |
Using a steel square, measure the deviation of the inner compression spring.
| 4. INSPECT INTAKE VALVE |
![]() |
Using a micrometer, measure the diameter of the valve stem.
![]() |
Using a vernier caliper, measure the valve head margin thickness.
![]() |
Using a vernier caliper, measure the valve's overall length.
| 5. INSPECT EXHAUST VALVE |
![]() |
Using a micrometer, measure the diameter of the valve stem.
![]() |
Using a vernier caliper, measure the valve head margin thickness.
![]() |
Using a vernier caliper, measure the valve's overall length.
| 6. INSPECT VALVE GUIDE BUSH OIL CLEARANCE |
![]() |
Using a caliper gauge, measure the inside diameter of the guide bush.
Subtract the valve stem diameter measurement from the guide bush inside diameter measurement.
| Item | Specified Condition |
| Intake | 0.025 to 0.060 mm (0.000984 to 0.00236 in.) |
| Exhaust | 0.030 to 0.065 mm (0.00118 to 0.00256 in.) |
| Item | Specified Condition |
| Intake | 0.08 mm (0.00315 in.) |
| Exhaust | 0.10 mm (0.00394 in.) |
| 7. INSPECT INTAKE VALVE SEAT |
![]() |
Apply a light coat of Prussian blue to the valve face.
Lightly press the valve face against the valve seat.
Check the valve face and valve seat.
Check that the contact surfaces of the valve seat and valve face are in the middle area of their respective surfaces, with the width between 1.1 to 1.5 mm (0.0433 to 0.0591 in.).
If not, correct the valve seat.
Check that the contact surfaces of the valve seat and valve face are even around the entire valve seat.
If not, correct the valve seat.
| 8. INSPECT EXHAUST VALVE SEAT |
![]() |
Apply a light coat of Prussian blue to the valve face.
Lightly press the valve face against the valve seat.
Check the valve face and valve seat.
Check that the contact surfaces of the valve seat and valve face are in the middle area of their respective surfaces, with the width between 1.1 to 1.5 mm (0.0433 to 0.0591 in.).
If not, correct the valve seat.
Check that the contact surfaces of the valve seat and valve face are even around the entire valve seat.
If not, correct the valve seat.
| 9. INSPECT CYLINDER HEAD SUB-ASSEMBLY |
![]() |
Using a precision straightedge and feeler gauge, measure the warpage of the contact surfaces of the cylinder block and manifold.
| Item | Specified Condition |
| Cylinder head lower side | 0.05 mm (0.00197 in.) |
| Intake side | 0.08 mm (0.00315 in.) |
| Exhaust side | 0.05 mm (0.00197 in.) |
![]() |
Using a dye penetrant, check the intake ports, exhaust ports and cylinder surface for cracks.
If cracked, replace the cylinder head.