Home › ENGINE ยท 3UR-FBE › LUBRICATION › OIL PUMP

OIL PUMP > INSTALLATION

for Preparation Click here



1. INSTALL WATER INLET PIPE
  1. Apply soapy water to 2 new O-rings and install them to the water inlet pipe.

  1. Install the water inlet pipe to the No. 1 heat exchanger cover.



2. INSTALL TIMING CHAIN COVER SUB-ASSEMBLY
  1. Apply a light coat of engine oil to a new oil pump gasket.

  1. Install the oil pump gasket to the cylinder block.

  1. Apply a light coat of engine oil to a new O-ring.

  1. Install the O-ring to the oil pan sub-assembly.



  1. Apply seal packing in a continuous line to the timing chain cover sub-assembly as shown in the following illustration.


    A178520E04


    Text in Illustration 
    *a
    Continuous Line Area
    *b
    Dashed Line Area
    *c
    Diagonal Line Area
    -
    -

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


    1. A150825E09

      Apply Seal Packing As Follows:
      Area
      Seal Packing Diameter
      Application Position from Inside Edge of Cover
      Continuous line area
      3.0 to 4.0 mm (0.118 to 0.157 in.)
      2.5 mm (0.0984 in.)
      Dashed line area
      6.4 mm (0.252 in.) or more, or within OK area shown in illustration
      7.0 mm (0.276 in.)
      Diagonal line area
      3.0 to 4.0 mm (0.118 to 0.157 in.)
      5.5 mm (0.217 in.)

    Text in Illustration 
    *a
    Seal Packing Thickness
    *b
    Seal Packing Width
    *c
    OK Area

    NOTICE:
    1. When the contact surfaces are wet, wipe them with an oil-free cloth before applying seal packing.
    2. Install the timing chain cover sub-assembly within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.
    3. Do not start the engine for at least 2 hours after installing.



    A162541
  1. Align the oil pump drive rotor spline and crankshaft as shown in the illustration. Install the spline and timing chain cover sub-assembly to the crankshaft.



    A162542E04
  1. Temporarily install the timing chain cover sub-assembly with the 28 bolts and nut.

    Standard Bolt:
    Item
    Length
    Thread Diameter
    Bolt A
    25 mm (0.984 in.)
    8 mm (0.315 in.)
    Bolt B
    55 mm (2.17 in.)
    8 mm (0.315 in.)
    Bolt C
    70 mm (2.76 in.)
    8 mm (0.315 in.)
    Bolt D
    35 mm (1.38 in.)
    10 mm (0.394 in.)
    Bolt E
    55 mm (2.17 in.)
    10 mm (0.394 in.)
    Bolt F
    80 mm (3.15 in.)
    10 mm (0.394 in.)

    Text in Illustration 
    *1
    Nut

    NOTICE:
    Make sure that there is no oil on the bolt threads.



    A174145E01
  1. Tighten the 3 bolts in several steps in the sequence shown in the illustration.

    Torque:
    47 N*m{ 479 kgf*cm , 35 ft.*lbf }



    A163330E01
  1. Temporarily install the fan bracket assembly with the 4 bolts.

    Standard Bolt:
    Item
    Length
    Thread Diameter
    Bolt A
    70 mm (2.76 in.)
    8 mm (0.315 in.)
    Bolt B
    80 mm (3.15 in.)
    10 mm (0.394 in.)

  1. Temporarily install the V-ribbed belt tensioner assembly with the standard bolt and 6 mm hexagon bolt.



    A174146E01
  1. Tighten the 8 bolts labeled 4 to 11 in several steps in the sequence shown in the illustration.

    Torque:
    47 N*m{ 479 kgf*cm , 35 ft.*lbf }



    A162544E01
  1. Tighten the 23 bolts and nut labeled 12 to 35 in several steps in the sequence shown in the illustration.

    Torque:
    23 N*m{ 235 kgf*cm , 17 ft.*lbf }


    NOTICE:
    A162545E01
    After the installation, if the seal packing has seeped out at the areas labeled A shown in the illustration, wipe it off.



3. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH
  1. Install 5 new gaskets to the No. 2 camshaft bearing cap and No. 3 camshaft bearing cap.

  1. Install the gasket to the cylinder head cover sub-assembly LH.

    NOTICE:
    Remove any oil from the contact surface.



    A291560E01
  1. Apply seal packing as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Text in Illustration 
    V100135
    Seal Packing

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the cylinder head cover sub-assembly LH within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.



    A162523E01
  1. Install the cylinder head cover sub-assembly LH washer with a new seal and the 14 bolts.

    Torque:
    for bolt A:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }
    except bolt A:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

    NOTICE:
    Do not start the engine for at least 2 hours after the installation.



4. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY RH
  1. Install 5 new gaskets to the No. 1 camshaft bearing cap and No. 3 camshaft bearing cap.

  1. Install the gasket to the cylinder head cover sub-assembly RH.

    NOTICE:
    Remove any oil from the contact surface.



    A291561E01
  1. Apply seal packing as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Text in Illustration 
    V100135
    Seal Packing

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the cylinder head cover sub-assembly RH within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.



    A162525E01
  1. Install the cylinder head cover sub-assembly RH washer with a new seal and the 14 bolts.

    Torque:
    for bolt A:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }
    except bolt A:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

    NOTICE:
    Do not start the engine for at least 2 hours after the installation.



5. INSTALL IGNITION COIL ASSEMBLY
  1. Install the 8 ignition coils with the 8 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



6. INSTALL CRANKSHAFT PULLEY


    A164230E07
  1. Align the crankshaft pulley set key with the key groove of the crankshaft pulley, and slide on the crankshaft pulley.
    Text in Illustration 
    *a
    Hold
    *b
    Turn
    *c
    SST

  1. Using SST, install the crankshaft pulley set bolt.

    SST
    09213-70011  
    09330-00021  

    Torque:
    300 N*m{ 3059 kgf*cm , 221 ft.*lbf }



7. CONNECT WIRE HARNESS CLAMP BRACKET
  1. Connect the wire harness clamp bracket to the timing chain cover sub-assembly with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



8. INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY
  1. Install the No. 1 idler pulley sub-assembly with the bolt.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }



9. INSTALL WATER PUMP PULLEY
  1. Temporarily install the water pump pulley with the 4 bolts.

  1. Using SST, hold the water pump pulley and tighten the 4 bolts.

    SST
    09960-10010   (09962-01000, 09963-01000)

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



10. INSTALL WATER INLET HOUSING


    A162555E05
  1. Install a new gasket to the timing chain cover sub-assembly.
    Text in Illustration 
    *1
    Gasket

  1. Install the water inlet housing with the 3 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



11. INSTALL AIR TUBE SUB-ASSEMBLY
  1. Connect the 2 hoses.

  1. Install the air tube sub-assembly with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



12. INSTALL NO. 1 ENGINE COVER


A158656

NOTICE:
Make sure that the No. 1 engine cover is level with the top surface of the intake port of the cylinder head for 1 and 2.

HINT:
  1. Align the No. 1 engine cover cutouts with the air tube.
  2. Align the No. 1 engine cover with the air switching valve surface and cylinder head wall.



13. INSTALL NO. 2 ENGINE COVER


A307709

NOTICE:
Make sure that the No. 2 engine cover is level with the top surface of the intake port if the cylinder head.

HINT:
  1. Align the No. 2 engine cover cutout with the air tube.
  2. Align the No. 2 engine cover with the front water by-pass joint and cylinder head wall.



14. INSTALL FRONT WATER BY-PASS JOINT
  1. Install 2 new gaskets and the front water by-pass joint with the 4 nuts to the cylinder head.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Connect the No. 2 water by-pass hose to the front water by-pass joint, and slide the clamp to secure the hose.



15. CONNECT NO. 10 WATER BY-PASS HOSE


    A291559E03
  1. Connect the No. 10 water by-pass hose to the front water by-pass joint, and slide the clamp to secure the hose.
    Text in Illustration 
    *1
    No. 9 Water By-pass Hose
    *2
    No. 10 Water By-pass Hose
    *a
    Paint Mark (Orange)
    *b
    Paint Mark (Yellow)



16. CONNECT NO. 9 WATER BY-PASS HOSE
  1. Connect the No. 9 water by-pass hose to the front water by-pass joint, and slide the clamp to secure the hose.



17. INSTALL WATER BY-PASS PIPE SUB-ASSEMBLY
  1. Connect the No. 2 water by-pass hose and No. 3 water by-pass hose to the water by-pass pipe sub-assembly, and slide the 2 clamps to secure the hoses.

  1. Install the water by-pass pipe sub-assembly with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Connect the air tube sub-assembly with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



18. INSTALL NO. 1 WATER BY-PASS HOSE
  1. Connect the No. 1 water by-pass hose to the inlet water housing and front water by-pass joint, and slide the 2 clamps to secure the hoses.



19. INSTALL GENERATOR ASSEMBLY
  1. Install the 2 stud bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Install the generator assembly with the 2 bolts and 2 nuts.

    Torque:
    43 N*m{ 439 kgf*cm , 32 ft.*lbf }

  1. Connect the generator connector.

  1. Connect the generator wire with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Install the terminal cap.

  1. Connect the wire harness bracket to the generator assembly with the bolt.

    Torque:
    31 N*m{ 316 kgf*cm , 23 ft.*lbf }



20. CONNECT VANE PUMP ASSEMBLY


A163333E05

HINT:
Before performing the following procedures, move the spacer until the vane pump assembly can be installed.
Text in Illustration 
*a
Spacer

  1. Connect the vane pump assembly to the timing chain cover sub-assembly with the 2 bolts.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }



21. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE
  1. Apply a light coat of engine oil to a new O-ring.



    A164434E01
  1. Install the O-ring to the guide.

  1. Install the dipstick guide with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Install the dipstick.



22. INSTALL OIL FILTER BRACKET (w/o Oil Cooler)
  1. Apply a light coat of engine oil to 2 new O-rings.

  1. Install the 2 O-rings to the timing chain cover sub-assembly.

  1. Install the oil filter bracket with the 2 bolts and 2 nuts.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }



23. INSTALL OIL FILTER BRACKET (w/ Oil Cooler)


    A162470
  1. Apply a light coat of engine oil to 2 new O-rings.

  1. Install the 2 O-rings to the timing chain cover.



    A162469
  1. Install the oil filter bracket with the 2 nuts and 2 bolts.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }



24. INSTALL NO. 1 OIL COOLER BRACKET (w/ Oil Cooler)


    A163672
  1. Connect the ground wire to the cylinder block.

  1. Install the oil cooler bracket with the 2 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



25. INSTALL NO. 2 WATER BY-PASS PIPE (w/ Oil Cooler)
  1. Connect the 4 hoses to the No. 2 water by-pass pipe, and slide the 4 clamps to secure the hoses.

  1. Install the No. 2 water by-pass pipe with the 3 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



26. INSTALL OIL PRESSURE SENDER GAUGE ASSEMBLY


    A186675E01
  1. Apply adhesive to 2 or 3 threads of the oil pressure sender gauge.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



    A162467
  1. Install the oil pressure sender gauge.

    Torque:
    15 N*m{ 153 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Do not start the engine within 1 hour after installation.



    A163657
  1. Connect the sender gauge connector.



27. INSTALL OIL FILTER ELEMENT


    A178458E01
  1. Clean the inside of the oil filter cap, its threads and its O-ring groove.



    A284602E01
  1. Apply a small amount of engine oil to a new O-ring and install it to the oil filter cap.

    NOTICE:
    1. Be sure to install the O-ring in the proper location, otherwise oil may leak.
    2. Do not twist the O-ring.

  1. Set a new oil filter element to the oil filter cap.

  1. Remove any dirt or foreign matter from the installation surface of the engine.

  1. Apply a small amount of engine oil to the O-ring again and temporarily install the oil filter cap.



  1. Using SST, tighten the oil filter cap.

    SST
    09228-06501  

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }



    A284603E01

    NOTICE:
    1. When tightening the oil filter cap, do not remove the oil filter bracket clip.
    2. Make sure that the oil filter is installed securely as shown in the illustration.
    3. Be careful that the O-ring does not get caught between any surrounding parts.
    4. After tightening the oil filter cap, make sure that there is no gap and that the O-ring is not protruding.



    A162466E01
  1. Apply a small amount of engine oil to a new drain plug O-ring, and install it to the oil filter cap.

    NOTICE:
    Before installing the O-ring, remove any dirt or foreign matter from the installation surface of the oil filter cap.

  1. Install the oil filter drain plug.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }

    NOTICE:
    Be careful that the O-ring does not get caught between any surrounding parts.



28. CONNECT NO. 2 FUEL TUBE SUB-ASSEMBLY
  1. Connect the No. 2 fuel tube sub-assembly with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



29. CONNECT COOLER COMPRESSOR ASSEMBLY


    A163332E01
  1. Install the cooler compressor assembly with the 2 stud bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Install the 2 bolts and 2 nuts.

    NOTICE:
    Tighten the bolts and nuts in the order shown in the illustration to install the cooler compressor assembly.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }



30. CONNECT HEATER HOSE AND PIPE
  1. Connect the 3 hoses, and slide the 3 clamps to secure the hoses.

  1. Install the 2 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



31. CONNECT AIR PUMP HOSE AND WIRE HARNESS
  1. Connect the No. 2 air hose and No. 3 air hose to the air tube sub-assembly, and slide the 2 clamps to secure the hoses.

  1. Connect the 2 clamps and air pump wire harness.



32. INSTALL INTAKE MANIFOLD
(Click here)


33. CONNECT ENGINE WIRE
  1. Engine Room RH Side:

    1. Connect the 7 clamps.

    2. Connect the throttle position sensor and throttle control motor connector.

    3. Connect the 2 air pump connectors.

    4. Install the ground wire RH with the 2 bolts.

      Torque:
      8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    5. Connect the 2 VVT sensor connectors.

    6. Connect the injector connector.

    7. Connect the 4 ignition coil connectors.

    8. Connect the 2 camshaft timing oil control valve connectors.

    9. Connect the 2 clamps and power steering oil pressure switch connector.

    10. Connect the clamp and junction connector.

  1. Engine Room LH Side:

    1. Connect the cooler compressor connector.

    2. Connect the 3 clamps.

    3. Connect the camshaft position sensor connector.

    4. Connect the 2 camshaft timing oil control valve connectors.

    5. Connect the engine coolant temperature sensor connector.

    6. Connect the 5 clamps.

    7. Install the ground wire LH with the 2 bolts.

      Torque:
      8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    8. Connect the 2 VVT sensor connectors.

    9. Connect the 4 ignition coil connectors.

    10. Connect the injector connector.

    11. Connect the 2 wire harness clamps.

    12. Connect the 4 air injection control driver connectors.

    13. Connect the 2 connectors and attach the 2 clamps to the engine room junction block.

    14. Install the engine room relay block cover.



34. INSTALL AIR CLEANER ASSEMBLY


    A309638E01
  1. Install the air cleaner case with the 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Install the air cleaner element onto the air cleaner case.



    A309637E01
  1. Install the air cleaner cap.

    1. for Type A:
      Install the air cleaner cap and fasten the 4 hook clamps.

    2. for Type B:
      Install the air cleaner cap and fasten the 2 hook clamps.

    3. Connect the MAF meter connector.

    4. Attach the wire harness clamp.



35. INSTALL AIR CLEANER HOSE ASSEMBLY
  1. Install the air cleaner hose assembly with the 2 hose clamps.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

  1. Connect the vacuum hose to the air cleaner hose assembly.

  1. Connect the ventilation hose to the air cleaner hose assembly, and slide the clamp to secure the hose.



36. INSTALL RADIATOR ASSEMBLY
(Click here)


37. ADD ENGINE OIL
  1. Add fresh oil.

    Standard Oil Grade:
    Oil Grade
    Oil Viscosity (SAE)
    ILSAC GF-5 multigrade engine oil
    0W-20

    Standard Oil Capacity:
    Item
    Specified Condition
    Drain and refill without oil filter change
    7.1 liters (7.5 US qts, 6.2 Imp. qts)
    Drain and refill with oil filter change
    7.5 liters (7.9 US qts, 6.6 Imp. qts)
    Dry fill
    9.3 liters (9.8 US qts, 8.2 Imp. qts)

  1. Install the oil filler cap.



38. ADD ENGINE COOLANT
  1. Add engine coolant.
    Standard capacity: 
    Item
    Specified Condition
    w/ Trailer Towing System
    13.0 liters (13.7 US qts, 11.4 Imp. qts)
    w/o Trailer Towing System
    12.1 liters (12.8 US qts, 10.6 Imp. qts)

    NOTICE:
    Do not substitute plain water for engine coolant.

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).
    2. Please contact your Toyota dealer for further details.



    A151850E05
  1. Slowly pour coolant into the radiator reservoir until it reaches the FULL line.

  1. Install the reservoir cap.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.

  1. Install the radiator cap.

  1. Start the engine and warm it up until the thermostat opens.

    HINT:
    The thermostat opening timing can be confirmed by pressing the radiator inlet hose by hand, and checking when the engine coolant starts to flow inside the hose.

  1. Maintain the engine speed at 2000 to 2500 rpm.

    NOTICE:
    1. Make sure that the radiator reservoir still has some coolant in it.
    2. Pay attention to the needle of the water temperature meter. Make sure that the needle does not show an abnormally high temperature.
    3. If there is not enough coolant, the engine may burn out or overheat.
    4. Immediately after starting the engine, if the radiator reservoir does not have any coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the FULL line.
    5. Run the engine at 2000 rpm until the coolant level has stabilized.

  1. Press the inlet and outlet radiator hoses several times by hand to bleed air.

    CAUTION:
    1. Wear protective gloves.
    2. Be careful as the radiator hoses are hot.
    3. Keep your hands away from the fan.

  1. Stop the engine, and wait until the engine coolant cools down to ambient temperature.

    CAUTION:
    Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    A161780E01
  1. Check that the coolant level is between the FULL and LOW lines.
    If the coolant level is below the LOW line, repeat all of the procedures above.
    If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW lines.



39. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


40. INSPECT FOR OIL LEAK
  1. Start the engine. Make sure that there are no oil leaks from the area that was worked on.



41. INSPECT FOR COOLANT LEAK


A161766

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.



42. CHECK ENGINE OIL LEVEL
  1. Warm up the engine, then stop the engine and wait for 5 minutes.

  1. Check that the engine oil level is between the low level and full level marks on the dipstick.
    If low, check for leakage and add oil up to the full level mark.

    NOTICE:
    Do not fill engine oil above the full level mark.

    HINT:
    A certain amount of engine oil will be consumed while driving. In the following situations, oil consumption may increase, and engine oil may need to be refilled in between oil maintenance intervals.
    1. When the engine is new, for example directly after purchasing the vehicle or after replacing the engine.
    2. If low quality oil or oil of an inappropriate viscosity is used.
    3. When driving at high engine speed or with a heavy load, (when towing, or), when driving while accelerating or decelerating frequently.
    4. When leaving the idling for a long time, or when driving frequently through heavy traffic.
    When judging the amount of oil consumption, keep in mind that the oil may have become diluted, making it difficult to judge the true level accurately.