OIL PUMP > REMOVAL |
| 1. DISCHARGE FUEL SYSTEM PRESSURE |
Disconnect the cable from the negative (-) battery terminal.
![]() |
Disconnect the 2 fuel pump ECU connectors.
Connect the cable to the negative (-) battery terminal.
Start the engine. After the engine has stopped on its own, turn the ignition switch off.
Crank the engine again, and then check that the engine does not start.
Loosen the fuel tank cap, and then discharge the pressure in the fuel tank completely.
Connect the 2 fuel pump ECU connectors.
| 2. PRECAUTION |
| 3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 4. DRAIN ENGINE OIL |
Remove the oil filler cap.
Remove the oil pan drain plug and gasket, and drain the engine oil into a container.
Install a new gasket and the oil pan drain plug.
| 5. DRAIN ENGINE COOLANT |
Loosen the radiator drain cock plug.
Remove the radiator cap. Then drain the coolant from the radiator.
Loosen the 2 cylinder block drain cock plugs. Then drain the coolant from the engine.
Tighten the 2 cylinder block drain cock plugs.

Tighten the radiator drain cock plug by hand.
| 6. REMOVE RADIATOR ASSEMBLY |
| 7. REMOVE AIR CLEANER HOSE ASSEMBLY |
![]() |
Disconnect the vacuum hose from the air cleaner hose assembly.
Slide the clamp and disconnect the ventilation hose from the air cleaner hose assembly.
Loosen the 2 hose clamps.
Remove the air cleaner hose assembly.
| 8. REMOVE AIR CLEANER ASSEMBLY |
![]() |
Remove the air cleaner cap.
Disconnect the MAF meter connector.
Using a clip remover, detach the wire harness clamp.
for Type A:
Unfasten the 4 hook clamps and then remove the air cleaner cap.
for Type B:
Unfasten the 2 hook clamps and then remove the air cleaner cap.
Remove the air cleaner element.
![]() |
Remove the 2 bolts and air cleaner case.
| 9. DISCONNECT ENGINE WIRE |
Engine Room LH Side:
![]() |
Remove the engine room relay block cover.
Disconnect the 2 connectors and detach the 2 clamps from the engine room junction block.
![]() |
Disconnect the 4 air injection control driver connectors.
![]() |
Disconnect the 2 wire harness clamps.
![]() |
Disconnect the injector connector.
Disconnect the 4 ignition coil connectors.
Disconnect the 2 VVT sensor connectors.
Disconnect the 5 clamps.
Remove the 2 bolts and ground wire LH.
![]() |
Disconnect the engine coolant temperature sensor connector.
Disconnect the 2 camshaft timing oil control valve connectors.
Disconnect the camshaft position sensor connector.
Disconnect the 3 clamps.
Disconnect the cooler compressor connector.
![]() |
Engine Room RH Side:
Disconnect the 2 camshaft timing oil control valve connectors.
Disconnect the 4 ignition coil connectors.
Disconnect the injector connector.
Disconnect the 2 VVT sensor connectors.
Remove the 2 bolts and ground wire RH.
Disconnect the 2 air pump connectors.
Disconnect the throttle position sensor and throttle control motor connector.
Disconnect the 7 clamps.
![]() |
Disconnect the 2 clamps and power steering oil pressure switch connector.
| *1 | Junction Connector |
Disconnect the clamp and junction connector.
| 10. REMOVE INTAKE MANIFOLD |
| 11. DISCONNECT AIR PUMP HOSE AND WIRE HARNESS |
![]() |
Slide the 2 clamps and disconnect the No. 2 air hose and No. 3 air hose from the air tube sub-assembly.
| *1 | No. 3 Air Hose |
| *2 | No. 2 Air Hose |
Disconnect the 2 clamps.
| 12. DISCONNECT HEATER HOSE AND PIPE |
![]() |
Remove the 2 bolts.
Slide the 3 clamps and disconnect the 3 hoses.
| 13. DISCONNECT COOLER COMPRESSOR ASSEMBLY |
![]() |
Remove the 2 bolts, 2 nuts and 2 stud bolts, and disconnect the cooler compressor assembly.
| 14. DISCONNECT NO. 2 FUEL TUBE SUB-ASSEMBLY |
![]() |
Remove the 2 bolts and disconnect the No. 2 fuel tube sub-assembly.
| *a | LH Side |
| *b | RH Side |
| 15. REMOVE OIL FILTER ELEMENT |
![]() |
Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.
![]() |
Remove the oil filter drain plug.
![]() |
Install the pipe to the oil filter cap.
![]() |
Check that oil is drained from the oil filter. Then disconnect the pipe and remove the O-ring, as shown in the illustration.
![]() |
Using SST, remove the oil filter cap.
![]() |
Remove the oil filter element and O-ring from the oil filter cap.
| 16. REMOVE OIL PRESSURE SENDER GAUGE ASSEMBLY |
![]() |
Disconnect the sender gauge connector.
![]() |
Remove the oil pressure sender gauge.
| 17. REMOVE NO. 2 WATER BY-PASS PIPE (w/ Oil Cooler) |
![]() |
Slide the 4 clamps and disconnect the 4 hoses from the No. 2 water by-pass pipe.
Remove the 3 bolts and No. 2 water by-pass pipe.
| 18. REMOVE NO. 1 OIL COOLER BRACKET (w/ Oil Cooler) |
![]() |
Remove the 2 nuts and bracket.
Disconnect the ground wire from the cylinder block.
| 19. REMOVE OIL FILTER BRACKET (w/ Oil Cooler) |
![]() |
Remove the 2 bolts, 2 nuts and filter bracket.
![]() |
Remove the 2 O-rings.
| 20. REMOVE OIL FILTER BRACKET (w/o Oil Cooler) |
![]() |
Remove the 2 bolts, 2 nuts and oil filter bracket.
![]() |
Remove the 2 O-rings.
| 21. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE |
Remove the dipstick.
![]() |
Remove the bolt and dipstick guide.
Remove the O-ring from the dipstick guide.
| 22. DISCONNECT VANE PUMP ASSEMBLY |
![]() |
Remove the 2 bolts and disconnect the vane pump assembly.
| 23. REMOVE GENERATOR ASSEMBLY |
![]() |
Disconnect the generator connector.
Remove the terminal cap and nut, and disconnect the generator wire.
![]() |
Remove the bolt and disconnect the wire harness bracket from the generator assembly.
![]() |
Remove the 2 bolts, 2 nuts and generator assembly.
Remove the 2 stud bolts.
| 24. REMOVE NO. 1 WATER BY-PASS HOSE |
![]() |
Slide the 2 clamps and remove the No. 1 water by-pass hose from the water inlet housing and front water by-pass joint.
| 25. REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY |
![]() |
Remove the bolt and disconnect the air tube sub-assembly.
![]() |
Slide the 2 clamps and disconnect the No. 2 water by-pass hose and No. 3 water by-pass hose from the water by-pass pipe sub-assembly.
Remove the 2 bolts and water by-pass pipe sub-assembly.
| 26. DISCONNECT NO. 9 WATER BY-PASS HOSE |
![]() |
Slide the clamp and disconnect the No. 9 water by-pass hose from the front water by-pass joint.
| *1 | No. 9 Water By-pass Hose |
| *2 | No. 10 Water By-pass Hose |
| 27. CONNECT NO. 10 WATER BY-PASS HOSE |
Slide the clamp and disconnect the No. 10 water by-pass hose from the front water by-pass joint.
| 28. REMOVE FRONT WATER BY-PASS JOINT |
![]() |
Slide the clamp and disconnect the No. 2 water by-pass hose from the front water by-pass joint.
Remove the 4 nuts, front water by-pass joint and 2 gaskets.
| 29. REMOVE NO. 2 ENGINE COVER |
![]() |
| 30. REMOVE NO. 1 ENGINE COVER |
![]() |
| 31. REMOVE AIR TUBE SUB-ASSEMBLY |
![]() |
Remove the bolt, disconnect the 2 hoses, and remove the air tube sub-assembly.
| 32. REMOVE WATER INLET HOUSING |
![]() |
Remove the 3 bolts, water inlet housing and gasket.
| 33. REMOVE WATER PUMP PULLEY |
![]() |
Using SST, hold the water pump pulley.
| *a | SST |
Remove the 4 bolts and water pump pulley.
| 34. REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY |
![]() |
Remove the bolt and No. 1 idler pulley sub-assembly.
| 35. REMOVE FAN BRACKET ASSEMBLY |
![]() |
Remove the 4 bolts and fan bracket assembly.
| 36. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY |
![]() |
Remove the standard bolt, 6 mm hexagon bolt and V-ribbed belt tensioner assembly.
| 37. REMOVE IGNITION COIL ASSEMBLY |
Remove the 8 bolts and 8 ignition coils.
| 38. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH |
![]() |
Remove the 14 bolts, seal washer, cylinder head cover sub-assembly LH and gasket.
![]() |
Remove the 5 gaskets from the No. 2 camshaft bearing cap and No. 3 camshaft bearing cap.
| 39. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY RH |
![]() |
Remove the 14 bolts, seal washer, cylinder head cover sub-assembly RH and gasket.
![]() |
Remove the 5 gaskets from the No. 1 camshaft bearing cap and No. 3 camshaft bearing cap.
| 40. REMOVE CRANKSHAFT PULLEY |
![]() |
Using SST, loosen the crankshaft pulley set bolt.
| *a | SST |
| *b | Turn |
| *c | Hold |
Partially install the crankshaft pulley set bolt to the crankshaft pulley until 2 or 3 threads are engaged.
![]() |
Using the crankshaft pulley set bolt and SST, remove the crankshaft pulley.
| *a | SST |
| *b | Turn |
| *c | Hold |
| 41. DISCONNECT WIRE HARNESS CLAMP BRACKET |
![]() |
Remove the bolt and disconnect the wire harness clamp bracket.
| 42. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY |
![]() |
Remove the 28 bolts and nut shown in the illustration.
| *1 | Nut |
![]() |
Remove the timing chain cover sub-assembly by prying between it and the cylinder head and cylinder block with a screwdriver as shown in the illustration.
![]() |
Remove the oil pump gasket from the cylinder block.
![]() |
Remove the O-ring from the oil pan sub-assembly.
| 43. REMOVE WATER INLET PIPE |
![]() |
Remove the water inlet pipe from the No. 1 heat exchanger cover.
Remove the 2 O-rings from the water inlet pipe.