Home › COMMUNICATION SYSTEM › MULTIPLEX COMMUNICATION › LIN COMMUNICATION SYSTEM

LIN COMMUNICATION SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK)

E146648E05

  1. Disconnect the DA and DB main body ECU (driver side junction block) connectors.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    DA-1 (ACC) - Body ground
    B - Body ground
    ACC power supply
    Always
    11 to 14 V
    DA-1 (IG) - Body ground
    B - Body ground
    IG power supply
    Always
    11 to 14 V
    DB-21 (GND1) - Body ground
    B - Body ground
    Body ground
    Always
    Below 1 Ω
    DB-21 (GND2) - Body ground
    B - Body ground
    Body ground
    Always
    Below 1 Ω

    1. If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for Power Window Control System [w/ Jam Protection Function])

B191457E03

  1. Disconnect the N2 power window regulator master switch assembly connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    N2-3 (B) - N2-1 (E)
    L - W-B
    Battery power supply
    Always
    11 to 14 V
    N2-1 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω

    1. If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Power Window Control System [w/ Jam Protection Function])

B216712E05

  1. Disconnect the N12 front power window regulator motor assembly LH connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    N12-2 (B) - N12-1 (GND)
    G - W-B
    Battery power supply
    Always
    11 to 14 V
    N12-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω

    1. If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Power Window Control System [w/ Jam Protection Function])

B216712E06

  1. Disconnect the M11 front power window regulator motor assembly RH connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    M11-2 (B) - M11-1 (GND)
    V - W-B
    Battery power supply
    Always
    11 to 14 V
    M11-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω

    1. If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU) (w/ Sliding Roof System)

B160074E03

  1. Disconnect the W3 sliding roof drive gear sub-assembly connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    W3-9 (IG) - Body ground
    SB - Body ground
    IG power supply
    Ignition switch ON
    11 to 14 V
    Ignition switch OFF
    Below 1 V
    W3-10 (B) - Body ground
    L - Body ground
    +B power supply
    Always
    11 to 14 V
    W3-8 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

B160781E01

  1. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Check from the rear of the connector while it is connected to the air conditioning amplifier.


    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    J19-1 (IG+) - J19-14 (GND)
    P - W-B
    Ignition power supply
    Ignition switch ON
    11 to 14 V
    Ignition switch OFF
    Below 1 V
    J19-21 (B) - J19-14 (GND)
    BR - W-B
    Battery power source
    Always
    11 to 14 V
    J19-14 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    1. If the result is not as specified, the ECU may have a malfunction.


CHECK AIR CONDITIONING CONTROL ASSEMBLY

B353573E01

  1. Disconnect the J127 air conditioning control assembly connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    J127-4 (IG+) - J127-5 (GND)
    SB - W-B
    Ignition power supply
    Ignition switch ON
    11 to 14 V
    Ignition switch OFF
    Below 1 V
    J127-5 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω

    1. If the result is not as specified, there may be a malfunction on the wire harness side.